Question about 2001 Chrysler Voyager

Open Question

1997 chrysler voyager radio code problem

It seems ' wait 2 hr ' when press the power button and ignition is on positon

Posted by on

  • 2 more comments 
  • hayat_khan73 Jan 03, 2009

    I m having the same problem. radio says wait 2 hr

  • kenco446 Apr 05, 2009

    after putting in wrong code for my radio in my 1997 voyager message reads wait 2hr

  • baronneke Apr 28, 2009

    I'm having the same problem

  • Anonymous May 02, 2009

    i have a chrysler voyager2000 lx my radio does not work it comes on for a few seconds then goes off

×

4 Suggested Answers

  • 4807 Answers

SOURCE: I know the corect 4 digit radio code on my

The code must be incorrect.

Post the radio MODEL NUMER (begins with P ) and SERIAL NUMBER (begins with T) and I can check it for you

Posted on Jun 12, 2010

MrScary66613
  • 1990 Answers

SOURCE: serpentine belt chrysler grand voyager 3.3l 1997

http://www.mvreader.com/multiview/dayco/catalogSearch.php?autoCatalogSearch=1&make=CHRYSLER&model=TOWN%20%26% The Town and Country has the Exact same Motor, Here is the Link to the 3.3 Liter Belt Diagram. It is the First at the Top, Just read the Header. Please Rate My Response! Thanks!4ZYEV3

Posted on Feb 06, 2009

  • 4807 Answers

SOURCE: previous owner has lost radio code all i get is "wait" any help ?

First make sure that the code has not been noted somewhere within the car (underneath the ash tray, glove box , rear of sun visor etc) 

To see if your code is available here for free then the radio will have to be removed from the dashboard (and if you are lucky, someone may have written the code on the casing ) .

If not then POST ANOTHER QUESTION

quoting the radio MAKE+MODEL plus ALL the LETTERS+NUMBERS on ANY LABELS ,BARCODES or STAMPED IN THE METAL CASING

note: Unfortunately not all radios can be decoded using the Serial Number 

If not then try your Main Dealer ...........or take it into a Decode Service who will plug in a laptop to read/recode the memory chip (EEPROM). This takes a few minutes and shouldn`t be too expensive 



Posted on Sep 20, 2009

  • 1796 Answers

SOURCE: Hi there got chrysler grand voyager 1997 Le 3.3

Hi!!
Once you enter the right code you have to wait 2 full hours for the radio to come on. If you had entered a wrong code before, the wait can prolong. If you enter the right code, you do not have to do anything else but wait. Entering the wrong code 8 or 10 times will lock the radio for good.
Good Luck!!

Posted on Nov 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Unlocking gateway theft deterrent


go to the dealer
  1. Turn ON the ignition, with the engine OFF.
  2. Turn ON the radio.
Does the radio display LOC?
Is the security code known?
  1. Turn ON the ignition, with the engine OFF.
  2. Press and hold the radio preset buttons 2 and 3 for approximately 8 seconds until the first 3 digits of the backup code are displayed on the radio.
  3. Record the displayed code.
  4. Press and hold the AM/FM push button until the second 3 digits are displayed on the radio.
  5. Record the displayed code.
Could you successfully extract the code?
Contact Delco Electronics in order to give them the backup code information and to obtain an unlock code.
Did you complete the action?
Important:: If 8 unsuccessful tries are made to unlock the radio, the display will return to the LOC display, but when the SET button is pressed, INOP will be displayed. This means that the radio must be left powered up for 1 hour with the battery and the ignition applied before any more attempts to unlock the radio can be made. Anytime INOP is displayed, 3 more attempts will be allowed after the 1 hour waiting period with the battery and ignition applied.
  1. Ensure that the code to be used is correct.
  2. Turn ON the ignition, with the engine OFF.
  3. Press the MN button until 000 is displayed.
  4. Press and hold the HR button until the first 2 digits agree with the code.
  5. Press and hold the MN button until the last 2 digits agree with the code.
  6. Press the AM/FM button when the complete code is displayed. If REP appears on the display, repeat this step.
Did you successfully complete the action?
Replace the radio. Refer to Radio Replacement.
Did you complete the replacement?
Operate the system in order to verify the repair.
Did you complete the repair?

Apr 03, 2014 | 2001 Chevrolet S-10

1 Answer

What is the radio code for chrysler voyager 3.3 model 1997


Contact Chrysler and ask for your radio code , you will probably have to provide Radio type and model number and possibly serial number , to get these you will probably have to remove your radio..

Feb 15, 2013 | 1997 Chrysler Town & Country

1 Answer

Radio locked no code


Unlocking the Delco Radio Theft-Deterrent Feature After a Power Loss

If you know the code that was used to lock the radio then use the following instructions from the owner's manual to unlock the radio.
Quote:
Enter your secret code as follows; pause no more than 15 seconds between steps:
1. Turn the ignition on. LOC will appear on the display.
2. Press MIN and 000 will appear on the display.
3. Press MIN again until the last two digits agree with your code.
4. Press HR until the first one or two digits agree with your code.
5. Press AM-FM after you have confirmed that the code matches your secret code. The display will show SEC, indicating the radio is now operable and secure.

If you enter the wrong code eight times, INOP will appear on the display. You will have to wait an hour with the ignition on before you can try again. When you try again, you will only have three more chances (eight tries per chance) to enter the correct code before INOP appears.
If you don't know the code that was used to lock the radio then you will have to use the dealer's unlock procedure as follows. The dealer code changes over time - the one listed is current as of this posting. If it doesn't work try 08359 or search the forum for messages with a more recent code.
Quote:
1. Press and hold presets 2 & 3 for about 10 seconds until the first three digits of the display code are displayed.
2. Write the numbers down.
3. Press the AM-FM button, write down the next three numbers.
4. Call 1-800-537-5140. When asked, enter dealer code 202108, press the * button, and enter the six digit code from the radio. You will get an unlock code, write it down.
5. Go back to the car, press the HR button and set the first two numbers, press the MIN button and set the next two numbers, then press the AM-FM button. The display will show SEC, indicating the radio is now operable and secure.

To remove the code, repeat step 5. you should see --- on the radio face indicating the code is now out of the radio."

Dec 29, 2010 | 2000 GMC Jimmy

1 Answer

I know the corect 4 digit radio code on my Chrysler Voyager but when I put it in it still asks me to wait 2 hours?


The code must be incorrect.

Post the radio MODEL NUMER (begins with P ) and SERIAL NUMBER (begins with T) and I can check it for you

May 19, 2010 | 2004 Chrysler Voyager

2 Answers

Default code to unlock factory radio in a 2000


How to Reset GM Theft lock Radio's
Article Disclaimer: This article is meant to be used by Delco Radio owners to reset there radios. In no way is it meant to be used for any unethical or unlawful ways.

Purpose
The following instructions will allow you to reset any GM (General Motors), Cadillac, Oldsmobile, Buick, Pontiac theft lock radio.

Requirements
The theft lock radio must be in "LOC" mode.

Procedure:
1. Turn the ignition ON (The radio should display "LOC")
2. Hold down the Radio Presets 2 and 3 buttons for six seconds
3. The radio display changes from LOC to a three-digit number. Write this number down. You now have fifteen seconds to complete the next step.
4. Press the AM/FM button
5. The radio display changes to another three-digit number. Write this number to the right of the first one
6. You now have a six-digit number, the first three digits are from STEP 03 and the last three digits are form STEP 05
7. Call 1-800-537-5140
8. Press 1 then # (pound). You'll hear "Invalid Code, try again"
9. Press 139010 or 106010 or 206010 or 202107 then # (pound). You will be asked to enter your four or six digit code followed by *
10. Enter the number from STEP 6 then *
11. Listen to the four-digit number and write it down. It will be repeated twice
12. Turn the ignition ON (The radio displays LOC)
13. Use the MN and HR buttons to enter the code from STEP 11
14. Press the AM/FM button. The radio display changes to "SEC". Your radio is now "un-locked" and usable.

Dealership Codes
139010
106010
206010
202107

Troubleshooting
If you fail to enter the correct code eight times, the radio goes into INOP mode. You have to wait an hour with the ignition on before the radio returns to LOC mode.

To Read the original article or read similar articles please visit kingbain.com/how-to/unlock-gm-theftlock-radio-s

Good luck (remmeber comment and rated this).

May 05, 2010 | 2000 Chevrolet Silverado

1 Answer

Hi my battery whet dead n the mrs put in the wrong code 3 times now the radio says wait 2hrs that was 3 week ago and the lights under the radio flash consantly pls can you help me thanks.......gary


Hi Gary

Ther power will need to be on for 2hrs, that is the radio will need to be turned on for 2 hours with the ignition on. If you have done this already then the radio will need re-coding, this sometimes happens. You dont have to go to a dealer there is independant decoders around. let me know if you cant find pne.

Regards
Dan

Feb 28, 2010 | 2000 Chrysler Grand Voyager

1 Answer

My 99 Pontiac Grand Am's radio is on Loc. I have the 2 codes but I don't know what to do now?


turn ignition switch ON but leave stereo OFF---press MN button and OOO should appear -----press HR button to make the last two numbers match your code then release button ---press hr button until the first one or two numbers match ur code ----press AM/FM SEC should appear indicating the radio is unlocked if LOC shows up either took longer than 15 seconds between entering codes or wrong code entered --u r allowed only 8 tries after that radio becomes INOP and dealer is only one able to reset

Jan 21, 2010 | 1999 Pontiac Grand Am GT

2 Answers

1997 bonneville has LOC on the radio, How do I clear it?


if you dont have the code, the radio has to be removed and a gm dealer can get the code.

Oct 04, 2009 | 1997 Pontiac Bonneville

2 Answers

How do you input the code in our radio of our chrysler neon


see here  for the Neon 2001 - 2008 

http://www.torbaycarstereo.co.uk/chrysler_p05091610ab.html

or if not try here

http://www.radio-code.co.uk/code-entry-help-Chrysler.htm



Sep 19, 2009 | 2000 Chrysler Grand Voyager

1 Answer

Radio


Good Day,

The following procedure will give you a new code that you can use instead of your personal code. Using this new code, you can “unlock” your radio and then “re-lock” it with a new code if you wish. Prerequisites: The radio must be in LOC mode NOT in INOP mode. Let me explain. If you have activated the Theft-Deterrent feature of your radio and loose power, the radio goes into LOC (theftlock) mode. With the ignition on, you must use the MN and HR buttons to enter you personal code in order to unlock it (The instructions are on page 3-27 in your Owner’s manual). If you fail to enter the correct code eight (8) times, the radio goes into INOP mode. You have to wait an hour with the ignition on before the radio returns to LOC mode (go for a long drive somewhere).

Procedure:

01. Turn the ignition ON (The radio displays LOC)

02. Hold down the Radio Presets 2 and 3 buttons for six seconds

03. The radio display changes from LOC to a three-digit number. Write this number down. Don’t take forever, fifteen seconds max before the next step.

04. Press the AM/FM button

05. The radio display changes to another three-digit number. Write this number to the right of the first one.

06. You now have a six-digit number, the first three digits are from STEP 03 and the last three digits are form STEP 05

07. Call 1 800 537 5140 08. Press 1 then # (pound). You’ll hear “Invalid Code, try again”

09. Press 139010 then # (pound). You will be asked to enter your four or six digit code followed by * (start)

10. Enter the number from STEP 6 then * (star)

11. Listen to the four-digit number and write it down. It will be repeated twice

12. Turn the ignition ON (The radio displays LOC)

13. Use the MN and HR buttons to enter the code from STEP 11

14. Press the AM/FM button. The radio display changes to SEC Your radio is now “un-locked” and usable. The Theft-Deterrent feature is STILL active! If you want to disable it, use the instruction on page 3-27 in your Owner’s manual. Use the code from STEP 11 instead of your personal code.

I hope this helps

This came from:
http://answers.yahoo.com/question/index?qid=20070717061922AA7xMG3

Jun 30, 2008 | 1999 GMC Jimmy

Not finding what you are looking for?
2001 Chrysler Voyager Logo

Related Topics:

1,116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6876 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...