Question about 1988 Nissan Pathfinder

1 Answer

Front shocks I have a 1988 Nissan Pathfinder SE 6 cylinder, it has electric shocks and I am wondering if I can just put regular shocks on it. Thank You in Advance

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 99 Answers

Yes you can, remove the electric harness to the shock when you replace them. Disconnect the same at the connector, if permanently not worrying about electric shocks clip the connections and ensure no water gets in the clipped wireds by sealing them with silicon or remove the whole harness from the area.

Posted on Nov 28, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

BRAKE LIGHTS STOPPED WORKING ON 1988 PATHFINDER


GO TO YOUR BRAKE PEDAL WITH A FLASHLIGHT AND PUSH PEDAL IN WITH HAND AND SEE IF SWITCH IS ENGAGING,MAY JUST NEED ADJUSTING,IF IT IS ENGAGING,THEN SWITCH MAY BE BAD,EASY TO REMOVE,REMOVE ELECTRICAL CONNECTOR,THEN NUT HOLDING IT ON,HERE'S A LINK TO WHAT IT LOOK'S LIKE AND COST. Stoplight Switch 1988 Nissan Datsun Pathfinder 4WD 6 Cylinders 3 0L FI...

Sep 12, 2014 | Nissan Pathfinder Cars & Trucks

1 Answer

Where is (throttlie position sensor located) on se v6 1988 nissan pathfinder


Should be a small black box mounted on the side of the throttle body.

Jul 28, 2012 | 1988 Nissan Pathfinder

1 Answer

Can't get the fuel pump to work. put a new pump and relay and it still want work any suggestion. it's on a 1988 nissan pathfinder


I would recommend that you check the fuse panel. Take the fuse out and replace it w/ a new one.

Dec 04, 2011 | 1988 Nissan Pathfinder

1 Answer

How do i change the starter motor on a 1993 pathfinder


  1. Remove the exhaust manifold heat insulator.
  2. Remove the fuel tube retainer bolt.
  1. On 2wd models with the 6-cylinder engine:
    1. Remove the front right wheel.
    2. Remove the front gravel shield.
    3. Remove the exhaust manifold heat insulator.
    4. Remove the exhaust manifold.
    5. Detach the oil pressure switch connector.
  2. Unfasten the remaining electrical connections at the starter solenoid.
  3. Remove the two nuts holding the starter to the bell housing, then pull the starter toward the front of the vehicle and out.

To install:

  1. Insert the starter into the bell housing, being sure that the starter drive is not jammed against the flywheel.
  2. Tighten the attaching nuts and secure all electrical connections to the starter assembly.
  3. Install all remaining components in reverse order of removal.
  4. Reconnect the battery cables. If applicable, refill and check the oil level. Check the starter assembly for proper operation.



// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 31; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos'; c17hydro_100.gif

Starter removal on 2WD-6-cylinder engine






c17hydro_101.gif

Starter removal on 4WD-6-cylinder engine


On 4wd models with the 6-cylinder engine:

Remove the front gravel shield.

    1. Detach the oil pressure switch connector.
    2. Drain the engine oil and remove the oil filter.

Jan 19, 2011 | 1993 Nissan Pathfinder

2 Answers

TRYING TO FIND ENGINE SIZE ON 1990 NISSAN PATHFINDER SE 6 CLY 4 WHEEL DRIVE


either VG30E 3.0 litre 153 HP V6 or KA24E 2.4 litre 140 HP 4cyl

Jun 14, 2010 | 1990 Nissan Pathfinder

1 Answer

Where is the starter in a 1995 nissan pathfinder


Nissan Pick-ups and Pathfinder 1989-1995
Starter - REMOVAL & INSTALLATION
(see Figures 1 and 2)
  1. Disconnect the negative battery cable at the battery, then disconnect the positive battery cable at the starter.
4178adf.jpg


Fig. 1: Starter removal on 4WD-6-cylinder engine

74f3669.jpg

Fig. 2: Starter removal on 2WD-6-cylinder engine
  1. On 4wd models with the 6-cylinder engine:
    1. Remove the front gravel shield.
    2. Detach the oil pressure switch connector.
    3. Drain the engine oil and remove the oil filter.
CAUTION The EPA warns that prolonged contact with used engine oil may cause a number of skin disorders, including cancer! You should make every effort to minimize your exposure to used engine oil. Protective gloves should be worn when changing the oil. Wash your hands and any other exposed skin areas as soon as possible after exposure to used engine oil. Soap and water, or waterless hand cleaner should be used.
  1. On 2wd models with the 6-cylinder engine:
    1. Remove the front right wheel.
    2. Remove the front gravel shield.
    3. Remove the exhaust manifold heat insulator.
    4. Remove the exhaust manifold.
    5. Detach the oil pressure switch connector.

  2. Unfasten the remaining electrical connections at the starter solenoid.
  3. Remove the two nuts holding the starter to the bell housing, then pull the starter toward the front of the vehicle and out.

Hope this help (remember rated this).

May 18, 2010 | 1995 Nissan Pathfinder

1 Answer

Right order of spark plug wire help


For the 1998 Nissan Pathfinder 3.3L SOHC V6

Firing Order:
1-2-3-4-5-6

Cylinders:
......(back)......
|..5..|......|..6..|
|..3..|......|..4..|
|..1..|......|..2..|
......(front)

Distributor:
...(back)
......3..(+)-screw
4..........2
5..........1
(+)..6
...(front)

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

May 14, 2010 | 1998 Nissan Pathfinder

1 Answer

How to remove starter motor from 1988 nissan pathfinder? It is so cluttered there, is there an easy way?


DISCONNECT THE BATTERY FIRST.


Basically, remove the 2 bolts from the bell housing (pretty easy).
But the starter won't have enough clearance to drop down, so it has to be pulled over the cross member that holds the motor mounts, through to the front.

The electrical harness has a bolt that connects it to the engine block. This bolt has to be removed in order to give you enough slack to pull the starter all the way forward. Also, you have to remove the right tie rod and get it out of the way so you can pull the starter through.
Then, disconnect the two wires from the starter and reverse the process with your new starter.

Have a nice day, and thank you for using Fixya.

Mar 07, 2010 | 1988 Nissan Pathfinder

2 Answers

Air shocks, I think my pathfinder needs airshocks,


u can use regular shocks but u may get an air ride waring light staying on in the dash.

May 28, 2009 | 1993 Nissan Pathfinder

3 Answers

1992 nissan pathfinder se transmission will not engage in any gear


check the fluid level, start the engine, set the parking brake and shift it into neutral, and check the fluid level,

Aug 25, 2008 | 1988 Nissan Pathfinder

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

322 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...