Question about 1996 Toyota Tacoma

1 Answer

Noisy speedometer my 1996 Tpyota Tacoma speedometer that is clicking..what is the replacement procedure?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 344 Answers

The click you are hearing might be a dry speedometer cable. Applying grease to the inner cable will most likely help this problem. The problem is getting to the cable behind the speedometer/dash panel. You can also get to the cable from under the truck. if you crawl under the truck and look at the smaller end of the transmission, you will see the cable screwed into the tail piece of the transmission. Remove the cable from the transmission and pull the inner cable out of the outer cable. The inner cable is what spins and causes the speedometer to turn. Take regular wheel bearing grease in the palm of your hand and slid the inner cable through the grease then put the inner cable back in the outer cable. When the inner cable gets to the back of the speedometer, you will have to slowly turn the cable and give a slight pressure inward to seat the inner cable into the speedometer.

Hope this helps.

Good Luck

Posted on Nov 14, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is iat sensor located on 2006 tpyota tacoma 4,ol ?


Intake Air Temperature (IAT) sensor and Manifold Absolute Pressure (MAP) sensor are combined into a single assembly which is called Mass Air Flow (MAF) sensor. This MAF sensor is located on the air filter box near air filter hose, and is connected with a five wire connector. You cannot replace the IAT sensor alone. Instead a MAF sensor is replaced altogether.

25646166-ts5vql1j3jwqenesgxdwpnsg-5-0.png



25646166-ts5vql1j3jwqenesgxdwpnsg-5-2.png
Thank you for visiting Fixya.

Apr 14, 2015 | 2006 Toyota Tacoma

1 Answer

Where is the camshaft position sensor on a 1996 toyota tacoma 2.7 located.


Camshaft Position Sensor

1996 Toyota Truck Tacoma 2WD 2.4L EFI DOHC 4cyl

The Camshaft Position Sensor is located: Under hood, passenger side, front engine area, below valve cover, mounted in distributor

Oct 14, 2014 | 1996 Toyota Tacoma

2 Answers

My speedometer stop working what can i do to fix it


Causes...............

Faulty Vehicle Speed Sensor
- Vehicle speed sensor harness or connectors is open or shorted
- Vehicle speed sensor circuit poor electrical connection
- Faulty Engine Control Module (ECM)




The P0500 code is very common on the Toyota Tacoma, Toyota Yaris, Toyota Camry, Toyota Tundra, Toyota RAV-4. Before replacing the sensor you should try cleaning the sensor gear and erasing the code. If the light comes back you may have to replace the sensor.

Mar 12, 2014 | 1996 Toyota RAV4

1 Answer

How often do i need to change timing chain in my 1998 toyoota tacoma


you shouldn't need to unless the chain is noisy

Oct 07, 2012 | Cars & Trucks

1 Answer

1996 tacoma belt replacement, all belts


Dear Belt Replacer,
Nothing special you need to know, just that to make sure you take the belts off and reinstall them in the correct order, also make sure that each belt has between half an inch and one inch of play when the final tension is set on each belt, thx, I'M HERE TO HELP!!!

Nov 22, 2009 | 1998 Toyota Tacoma

1 Answer

Need fuse box diagram for 1996 toyota tacoma


go to local library and look @ hanes manual for free. You can also purchase one at napa or autozone, or buy the toyota shop factory manual for 100 dollars.

Jun 05, 2009 | 1996 Toyota Tacoma

1 Answer

Speedometer Squeaking Sound


I have a 1997 tacoma with 84,000 miles. i have the same problem and took the instrument cluster out. the problem appears to be with the speedometer cable and i plan on replacing it.

Nov 21, 2008 | 1997 Toyota Tacoma

4 Answers

Need to remove ignition switch


remove shroud
insert key into ignition turn to acc you will see a hole at the underneath of ignition housing with key on push in pin and pull switch out

Jul 24, 2008 | 1996 Toyota Tacoma

Not finding what you are looking for?
1996 Toyota Tacoma Logo

784 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...