Question about 2001 Buick LeSabre

1 Answer

How do I change the driver side running light?

The driver side running light is burned out.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 324 Answers

It is located under the hood, ot the side, you simply locate it and it turns and pulls out.

there should be a hole where the wire comes out find it and turn the socket out....

Posted on Nov 26, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My driver side turn signal only works during the day


just on the dash right....... because your dash lights turned on and it changes the brightness of the dash lights, try rolling the little wheel down on the left and see if there is a change?

on the other hand if the outside blinker light fails to work at night the bulb might be burned out you should check it and the dash light might not work if bulb is burned
just turn on the lights turn on the key and blinker and go look?

Apr 21, 2015 | Cars & Trucks

1 Answer

Why does the fuse burns on drivers side back running light when turned on.


Sounds like you have a short. Pull the bulb and try again. If the fuse does not burn (pop) then there may be a problem with bulb or the socket.
if the fuse still pops, then you will need to trace the lines, using a volt meter to find where the short is.

May 29, 2014 | 2004 Mitsubishi Endeavor

1 Answer

1999 dodge ram drivers back running light not working, yet the blinker and break light are working


The tail light bulbs are double filament with the low side being for the the running light and the bright side for the the brighter brake and turn. The low side of you bulb is burned out.

Apr 10, 2011 | Dodge Ram Cars & Trucks

1 Answer

I change the themostat hose but its still leaking from under neath on the driver side . and the coolant light comes on. also a awful smell like it burning


It sounds like a leaking intake manifold gasket to me. (Very common on GM V-6 engines) Look with a flashlight and see if you can see antifreeze running over the top of the transmission bell housing. Check both sides. On the side nearest the windshield and the side nearest the radiator.
Don't drive the car with a coolant leak. The aluminum heads are very unforgiving when it comes to overheating.

Dec 26, 2010 | 2001 Chevrolet Malibu

1 Answer

Drivers side tillight do;s not work but braklights do how do i fix it


You have a 2 filliment bulb,only the low filliment is burned or broken. This allows both the blinker and the brake lights to work but you have no parking or running light. Change the bulb, should be ok,

Apr 27, 2010 | 1998 Ford Windstar

1 Answer

Need to know how to change brake light on drivers side.


Open your life gate, take out the two screws holding that are holding the light in, pull away from car, if working on drivers side, pull to left and vice versa, twist out fitting for burned out light and replace.

Feb 11, 2010 | 1995 Toyota 4Runner

1 Answer

Why would the right rear running light(tail light) constantly burn out. 4 new bulbs in last 4 months, 2002 Jeep Grand Cherokee. No problems with left tail light. Automatic, Air, 4 wheel drive, 200300...


I have a 2002 JGC as well and its the driver side one with mine. I changed the bulb this last time and used bulb lube to cover all the metal. It worked for a mile then went out again but didnt burn out this time. I checked the contacts on the base and noticed there was some rust, scraped off with blade and used more bulb lube on those contacts too, working for now.

Jan 02, 2010 | 2002 Jeep Grand Cherokee

1 Answer

Wires burned no brake lights and one taillight doesnt work


Yes , The wiring in question does effect the brake lights because they all run on the same circuit.
I would repiar or repalce all the wiring and then replace the brake light switch. The switch could have shorted out from the fire.

Apr 11, 2009 | 1998 Dodge Caravan

1 Answer

03 pt ONLY driver brake light out


Ok you can't tell anyone, but I changed the wrong bulb. Only two choices and I changed the good bulb. ugh. all fixed now..

Jan 22, 2009 | 2006 Chrysler PT Cruiser

1 Answer

Head light burned out


just did 06 open hood look at top of light  should be 2 L shaped pins turn  and lift out whole light will lift out then change bulb no tools needed 06

Jan 07, 2009 | 2005 Chevrolet TrailBlazer

Not finding what you are looking for?
2001 Buick LeSabre Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...