Question about 2001 Ford Windstar

2 Answers

Engine stalls when skeaky sound coming from the water pump side. New water pump has been replaced , New belt tensioner and iddle bearings .No engined light shows up. No problem with restarting engine after stalling. It happened from time to time during driving , specally when stopping from the trafic light. Thank you for your technical support and your time. Dong

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

In my 2002 it was the engine synchronizer shaft( what used to the distributor )it sits on the left side of the intake manifold (viewed from front of car)theres a black sensor on top of it, the dealer replaced the hole thing in my case but after looking at the old part you could probably take the sensor off and squirt some engine old into bushing where the shaft comes out it looks like the bushing dries out after a while

Posted on Dec 22, 2008

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 19 Answers

Check charging system

Posted on Nov 22, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When engine gets to operating temperature noise from timing belt area whooo whooo, any ideas?


Sounds like water pump! If it was last changed 60k when timing belt done could need doing! If not timing belt tensioner! When timing belt is done it is good practice to replace water pump and belt tensioners at the same time!

Oct 23, 2014 | 2002 Nissan Frontier Crew Cab

1 Answer

Car runnning hot makes skeaky sounds


The water pump could be on its way out or the belt is slipping, check its tught by pressing on it firmly.. If it is tight then the water pump is completly ruined and its time for a new one

Jan 26, 2014 | Cars & Trucks

1 Answer

How to replace a serpentine belt on a nissan 2007 2.5 s altima


Video Tutorial:
https://youtu.be/h4qGOJ5PpSw

The easiest way to replace serpentine \ drive V belt on 2007-2012 Nissan Altima 2.5L 4 cylinders engine:
- remove front wheel on passenger side
- remove plastic splash cover
- user 14mm offset wrench to turn belt auto-tensioner in clockwise direction
- block auto-tensioner from moving using locking mechanism right above the auto-tensioner pulley
- slide the belt off the smooth non-grooved water pump pulley first
and then take the belt completely out
- when installing a new serpentine belt, first hook it onto all pulleys except for water pump pulley. Hook it onto the water pump pulley last
- make sure the new belt is hooked up properly onto all of the pulleys
- unlock the auto-tensioner
Original OEM Part #:
Amazon com OEM 11720 JA00B Nissan Altima Serpentine Belt
Follow this diagram to route the new belt on 2.5L engine:

replace-serpentine-belt-nissan-2007-2-5-02rhvdv200sh3oinuqbnuvnv-2-2.png

Jan 04, 2013 | 2007 Nissan Sentra 2.0 SL Sedan

1 Answer

Replace water pump torrent


drain coolant until below water pump level. loosen water pump pulley bolts.then remove drive belt by rotating belt tensioner.remove drive belt from the right of idler pulley.carefully release the drive belt tensioner spring tension.then remove water pump pulley bolts and pulley.remove water pump bolts and water pump pay attention to the position old water pump when removing water pump so you can line up new water pump holes to the engine. be sure clean engine water pump mounting surface use gasket remover dont scratch engine surface when cleaning removing old gasket material. take new water pump gasket get it mounting holes line up with new water pump mounting holes.when done getting engine water pump surface clean.water pump gasket paper you need to put thin layer of sealer on both sides of water pump gasket use RTV SILICONE.LET SET UP 10 MINUTES. PUT GASKET ON WATER PUMP BUT FIRST MAKE SURE LINE UP GASKET HOLES WITH WATER PUMP HOLES BEFORE PUTTING ON THE GASKET SEALER.when gasket sealer set up 10 minutes then install new water pump with gasket to the engine torque to 89 inch lbs.or 10 NM that is about 7 ft lbs torque.you should be able turn water pump by hand if you cant turn water pump by hand got too tight damage water pump shaft bearing.when all done wait for THREE HOURS. before adding coolant i let RTV CURE SOME. torque water pump pulley bolts 18 ft lbs.

Dec 28, 2012 | 2006 Pontiac Torrent

1 Answer

Water pump 2000 3.0 liter dodge caravan


For The 3.0 Motor. (3.3 Way down the line.)

Drain cooling system.
Remove timing belt. Refer to Engine for procedure.
Remove water pump mounting bolts.
Separate pump from water inlet pipe and remove water pump.

Timing Belt Removal
Raise vehicle and remove accessory drive belt splash shield (Fig. 66).
Remove accessory drive belts.
Remove crankshaft pulley and damper (Fig. 68).
Support engine and remove right side engine mount.
Remove engine support bracket (Fig. 67).
Remove timing belt covers (Fig. 67).
Mark belt running direction for installation (Fig. 69).
Loosen timing belt tensioner bolt (Fig. 71) and remove timing belt.
Remove crankshaft sprocket flange shield (Fig. 68). CAMSHAFT SPROCKETS To remove camshaft sprockets
Hold camshaft sprocket with Spanner Tool MB-990775. Loosen and remove bolt and washer (Fig. 70).
Remove camshaft sprocket from camshaft. To install camshaft sprockets:
Place camshaft sprocket on camshaft.
Install bolt and washer to camshaft. Using Spanner Tool MB-990775, hold camshaft sprocket and torque bolt to 95 Nm (70 ft. lbs.) (Fig. 70). TIMING BELT TENSIONER
Install timing belt tensioner and tensioner spring.
Hook spring upper end to water pump pin and lower end to tensioner bracket with hook out (Fig. 71).
Turn timing belt tensioner counterclockwise full travel in adjustment slot and tighten bolt to temporarily hold this position (Fig. 72).

INSTALLATION


Install timing belt on crankshaft sprocket and keep belt tight on tension side (Fig. 69). Install belt on the front (radiator side) camshaft sprocket. Install belt on the water pump pulley, rear camshaft sprocket and finally on the timing belt tensioner.
Rotate the front camshaft sprocket in opposite direction to take up belt slack. Check that all timing marks are aligned (Fig. 69).
Install crankshaft sprocket flange (Fig. 68).
Loosen tensioner bolt and allow spring to tension timing belt.
Turn crankshaft two full turns in clockwise direction. Turn smoothly and in clockwise direction ONLY.
Align the timing marks on the sprockets and tighten the timing belt tensioner locking bolt to 28 Nm (250 in. lbs.) torque.
Install timing belt covers.
Install engine support bracket.
Install right side engine mount.
Install crankshaft damper and pulleys (Fig. 68). Tighten damper center bolt to 135 Nm (100 ft. lbs.) .
Install accessory drive belts.
Install accessory drive belt splash shield (Fig. 66).

Be sure to also replace all the cam and crank seals why you are there. Might as well put a belt on too.

FOR THE 3.3 OR 3.8 MOTORS.

Drain Cooling System.
Remove accessory drive belt.
Remove right front lower fender shield.
Remove water pump pulley bolts and remove pulley.
Remove water pump mounting screws. Remove water pump.
Remove and discard O-ring seal.
Clean O-ring groove and O-ring surfaces on pump and chain case cover. Take care not to scratch or gouge sealing surface

Installation

Install new O-ring into groove.
Install water pump to chain case cover. Tighten screws to 12 Nm (105 inch lbs.) .
Rotate pump by hand to check for freedom of movement.
Position pulley on pump. Install screws and tighten to 30 Nm (250 inch lbs.) .
Install accessory drive belt.
Install right front lower fender shield.
Refill Cooling System.

FOR THE 2.4 MOTOR

Disconnect negative cable from battery.
Raise vehicle on a hoist. Remove right inner splash shield.
Remove accessory drive belts.
Drain cooling system.
Support engine from the bottom and remove right engine mount.
Remove right engine mount bracket.
Remove timing belt. Refer to Engine for procedure.
Remove timing belt idler pulley.
Hold camshaft sprocket with Special tool C-4687 and adaptor C-4687-1 while removing bolt. Remove both cam sprockets.
Remove rear timing belt cover.

Install new O-ring gasket in water pump body O-ring groove. CAUTION: Make sure O-ring is properly seated in water pump groove before tightening screws. An improperly located O-ring may cause damage to the O-ring and cause a coolant leak.
Assemble pump body to block and tighten screws to 12 Nm (105 inch lbs.) . Pressurize cooling system to 15 psi with pressure tester and check water pump shaft seal and O-ring for leaks.
Rotate pump by hand to check for freedom of movement.
Install rear timing belt cover.
Install camshaft sprockets and torque bolts to 101 Nm (75 ft. lbs.) .
Install timing belt idler pulley and torque mounting bolt to 61 Nm (45 ft. lbs.) .
Install timing belt. Refer to Engine for procedure.
Install right engine mount bracket and engine mount. Refer to Engine for procedure.
Fill cooling system.
Install accessory drive belts.
Lower vehicle and connect battery cable.

Mar 29, 2012 | Cars & Trucks

3 Answers

When I raise the hood and with motor running looking to my left there is a belt running and a squeaking noise at idle coming from that area. The van is front wheel drive so motor sits in there sideways.


Has it just started with cold weather? Does it squeal at first then as the engine is revved, stop squealing.

If so its probably your alternator belt has worked loose and needs tightening. I'd check this out first, if you've not done it before ask a friend with some know how for guidance. But as a guide, there should be about an inch of give when flexed on the longest run between 2 pulleys, if more then probably needs tightening. If more than a couple of years old, replace with a new one.

If it still squeals after tightening/replacing, you could have a faulty water pump bearing or pulley bearing. Either would require replacement to pre-empt catastrophic failure and resultant engine damage.

Dec 20, 2010 | 1998 Oldsmobile Silhouette

1 Answer

Remove water pump


Disconnect battery earth lead. Do not turn crankshaft or camshaft whn timing beld removed. Remove spark plugs to ease turning engine. Turn engine in normal direction of rotation (unless otherwise stated) Do not turn engine via camshaft or other sprockets. Observe all tightening torques. Remove engine, remve RH engine mounting. Remove auxiliary drive belts, water pump pulley, crankshaft pulley, timing belt upper cover, timing belt lower cover. Turn crankshaft clockwise to TDC on No. 1 cylinder, slacken tensioner bolts 5 & 6. Move tensioner away from belt and lightly tighten bolts. Remove timing belt. Remove water pump and replace with new one. Suggest to replace cambelt as well.
Installation
Ensure timing marks aligned3 & 4. Fit timing belt in anti-clockwise direction, standing at crankshaft sprocket. Ensure belt is taut between sprockets on non-tensioned side. Slacken tensioner bolt 5. slacken tensioner bolt 6. Allow tensioner to operate. Tighten tensioner bolt 6. Tighten tensioner bolt 5. Turn crankshaft on turn clockwise. Ensure crankshaft sprocket timing marks aligned 4.
Slacken tensioner bolt 5. Slacken tensioner bolt 6. Allow tensioner to operate. Tighten tensioner 6. Tighten torque: 20 - 26 Nm. Tighten tensioner bolt 5. tighten torque: 20 - 26 Nm. Apply thumb pressure to belt at middle. Approximately 5kg. Belt should deflect to 1/4 of tensioner bolt head width 7. Belt tention can also be set using burroghs (BT-33-73F) tension gauge 10 at middle. Turn crankshaft 90 ° anti clockwise. Check belt tension is 9.5 16,5kg (engine must be cold). Install components in reverse order of removal. Fit cranckshaft pully. Tighten crankshaft pully bolts 8. G4-J: Tightening torque: 12-15Nm.
G4-N/G4-k: Tightening torque: 10-12Nm
G4EA: Tighten crankshaft pully bolt 9. Tighten torque: 140-150Nm.

Nov 04, 2009 | Hyundai Excel Cars & Trucks

2 Answers

How do you fix the water pump on a 1997 nissan maxima? Where is the water pump located on a 1997 nissan maxima?


The water pump is located behind the timing chain cover. There are two black plates on the front cover. The one near the front of the car has the water pump behind it. The other one has the timing chain tensioner behind it. First you must drain the coolant. Then support engine and remove engine mount. Then remove drive belts. Then remove the two black plates. Push the tensioner in and lock it with a paper clip. Then remove the two bolts holding the tensioner and remove tensioner. Then remove the water pump bolts. Rotate engine crankshaft the take tension off of water pump (about 20 degrees). Then install two bolts into water pump threaded flange (M8). Tighten M8 evenly as water pump will come without damaging it. Check for corrosion. Then replace with new one. Make sure you use new "O" rings. Lubricate with engine oil. Put the original three bolts back in the water pump. Then install timing chain tensioner and black covers. Replace belts and engine mounts. Add coolant and pressure test system.

Aug 31, 2009 | 1997 Nissan Maxima

1 Answer

Skeaky serpentine belt


are you positive the squeek is coming form the belt area?

the squeek can be from several other places, fan clutches can cause a high speed squeek, take the fan off and see if that cures it, the water pump front bearing can also be the culprit but that is hard to figure out without swapping in a new water pump, and lastly look at the AC compressor clutch, see if the squeek changes when you turn on and off the AC

hope this helps,


Oct 12, 2008 | 1999 Chevrolet Blazer

Not finding what you are looking for?
2001 Ford Windstar Logo

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...