Question about 1993 Nissan Maxima

1 Answer

No power steering

Replaced the pump and tried 2 bleed any possible air bubbles out still have no power steering suspect faulty pump just want 2 make sure

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 260 Answers

Could be steering rack itself. bring fluid level down a bit and with someone steering back and forth, see if there is any swirling fluid movement. if so, pump should be ok. just steering wheel back and forth a few minutes should purge any air. belt is tight i assume.

Posted on Nov 15, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I bleed the air from the new pwr steering pump the pwr steering works but is spotty


Powered Steering , Just top up with fluid , and turn steering wheel Left & Right a few times. WITH ENGINE running , You can't bleed Powered Steering., not like bleeding brakes

Mar 13, 2015 | Cars & Trucks

1 Answer

Where is the bleed valve for a power steering box


Open the hood and check the level of the power-steering fluid by removing the power-steering reservoir cap. Add the correct fluid recommended in your owner's manual to bring the level up to the full mark. Be aware that fluid that looks foamy is an indication of air in the system. Replace the cap.
Locate the power-steering bleed valve on top of the steering box near the bottom of the engine bay. Follow the power-steering, high-pressure lines from the power-steering pump to the steering box if you have trouble locating it.
Push a 6-foot length of rubber hose onto the end of the bleed valve. Run the other end of the hose into a drain pan.
Start the engine. Loosen the bleed valve fitting slightly with an adjustable wrench in a counterclockwise direction. Turn the steering wheel all the way to its stop one way and then the other several times. Shut the engine off.
Close the bleed valve by tightening it with an adjustable wrench in a clockwise direction. Remove the power-steering reservoir cap, and add fluid to bring the level up to the full mark.
Observe the power-steering fluid that came out of the rubber hose into the drain pan. Repeat the above procedure if there are air bubbles in the fluid. Close the bleed valve and remove the rubber hose when there are no air bubbles in the fluid expelled from the bleed valve. Close the hood.
New Arrival V15 GDS VCI Diagnostic Tool for Hyundai and Kia

Sep 16, 2014 | Cars & Trucks

1 Answer

Why is power steering fluid spewing out of the cap after replacing bad leaking power steering pump


You have Air in the Power steering System and it needs to be bleed out, And to do this if you Jack the two front wheels off the ground and Let them Hang free so there is No Load on the steering at all. please put some type of stands under the car, You will need more power steering fluid but before you add this you need to start your Car and turn the steering Wheel Slow from left to Right a few times, You will hear a wearing Notice come from the pump and you will see more fluid come out of the pump as well, that is the air trying to bleed its self out. The fluid coming out will be air rated lots of bubbles in it, Now that you have done this the Noise from the pump should start to go quite at this Point you can start to Add the New power steering fluid slow to the reservoir and keep turning the steering wheel from left to right slow (Never Fast but slow ) Have a lot of rags to clean the Mess. Hope this helps you. :)

Jun 08, 2014 | 1991 Cadillac DeVille

1 Answer

On a 2001 honda civic, when I'm turning the power


Sounds like an air bubble in there. You need to bleed them.

Sep 13, 2013 | Cars & Trucks

2 Answers

94 4x4 3.0 v6 3vze 4runner ...power steering pump recently replaced by myself ,yet still does not work when braking hard or not accelerating ...is it possible it just needs a fluid flush or maybe an air...


It would appear that there is air in it. Try turning all the way left, and then all the way right a few times, and see if that helps. That should be all you need to do if it really is air. Let me know if it persists.

May 11, 2011 | Toyota 4Runner Cars & Trucks

1 Answer

How to change vane pump o/h kit


FIRST OF ALL TURN OFF RADIO REMOVE NEGATIVE BATTERY CABLE. THEN REMOVE POWER STEERING PUMP FLUID FROM POWER STEERING PUMP.USING A HAND PUMP SIPHON. BE CAREFUL DONT GET POWER STEERING FLUID ON CAR PAINT IT WILL DAMAGE PAINT JOB.PUT A DRAIN PAN UNDERNEATH CAR TO CATCH POWER STEERING FLUID THEN DISCONNECT POWER STEERING PUMP LINES.REMOVE POWER STEERING PUMP ADJUSTER BOLT AND MOUNTING BOLT.REMOVE POWER STEERING PUMP.MOST OF THE TIME NEW POWER STEERING PUMP DONT HAVE DRIVE PULLEY ON IT SO TAKE TO A MACHINE SHOP THE WILL REMOVE PULLEY FROM OLD PUMP AND PRESS ON THE PULLEY TO NEW POWER STEERING PUMP.BESURE TO BUY NEW O RINGS TO END OF PRESSURE LINE.ONCE NEW POWER STEERING PUMP HAS PULLEY IN PLACE AND YOU HAVE NEW O RING FOR HIGH PRESSURE LINE.INSTALL NEW PUMP.ADJUST BELT TENSION.NOW BLEED POWER STEERING PUMP WITH FRONT WHEELS POINT STRAIGHT A HEAD POSITION.POUR POWER STEERING FLUID IN PUMP UNTIL FLUID LEVEL ON COLD MARK ON POWER STEERING PUMP DIP STICK.KEEP ADDING FLUID UNTIL FLUID STOP DROPPING. START THE ENGINE LET IT RUN AT IDLE ADD MORE FLUID IF DROPS KEEP FLUID ON FULL COLD MARK.ON DIP STICK TURN OFF ENGINE.CHECK TO MAKE SURE POWER STEERING PUMP NOT LEAKING AT THE LINES THEN.SAFELY RAISE SUPPORT FRONT OF THE VECHICLE WITH JACK STANDS. MAKE SURE VECHICLE ON SOLID LEVEL GROUND CHECK.FLUID LEVEL MAKE SURE AT FULL COLD MARK. NOW START ENGINE.LET IDLE MINUTE.THEN TURN STEERING WHEEL ALL THE WAY TO THE LEFT TO RIGHT SEVERAL TIMES WITH OUT STOPPING IT IN PLACE. CHECK POWER STEERING FLUID WHEN FLUID LEVEL STOP DROPPING.AND FLUID IS NOT A TAN COLOR WHICH MEAN LOTS OF AIR IN SYSTEM. TURN OFF CAR UNTIL AIR BUBBLES DISAPPEAR.CHECK FLUID LEVEL BLEED POWER STEERING AGAIN. DONT DRIVE VECHICLE UNTIL STEERING FEEL NORMAL.IF FLUID REMAIN TAN WITH AIR BUBBLES CHECK FOR LEAKS AT POWER STEERING PUMP PRESSURE HOSE ORING. AND CHECK POWER STEERING LINES TO PUMP FOR LEAKS.

Mar 07, 2011 | 2000 Honda Civic

3 Answers

How do i bleed my power steering rack on subaru legacy rs turbo


if its been a week, there should no tbe any air. if its heavy, the rack could be bad, or weak pump????? any noises? air will usually cause a whiney noise, and there will be air whipped, foamy fluid in the pump. A pump pressure regulator could be stuck open, not allowing full pressure? I would have a shop diagnose it, tell them the history and see if they can find a cause.

Oct 16, 2009 | 1997 Subaru Legacy

2 Answers

Power steering pump is clicking and whining


It sounds like the power steering hydraulic system has air in it, causing the pump to whine and the bubbles to show up in the fluid. The clicking noise is probably just the power steer pressure switch operating normally, but you should probably take it back in to the repairer and get them to check it over if you're concerned. They should not have given it back to you if the power steer was not bled up properly, or at the very least should have advised you that it was not fully bled, but would come right after a couple of days.

Dec 03, 2008 | 2003 Honda Odyssey

2 Answers

Power steering - 1999 chevy silverado


You're going to have to bleed the system alot on those trucks. Just remove the return line and have an assistant turn the steering wheel back and forth just enough to engage the pump and filling the resevour while doing this. Keep bleeding until you have a good flow of P/S fluid out with no air bubbles. This can take a while.

Aug 24, 2008 | 1999 Chevrolet K1500

Not finding what you are looking for?
1993 Nissan Maxima Logo

197 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...