Question about 2002 Chrysler PT Cruiser

1 Answer

Need picture of a 2002 pt cruiser engine

Pic of engine specifically the timing belt area and the camshaft sensor area

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Free Repair Manual for 2001-2004 pt cruisers. It has tons of information with pictures. It saved me when i had to change my serpentine belt.

Posted on Jul 09, 2009

6 Suggested Answers

Keef2011
  • 160 Answers

SOURCE: 2002 PT Cruiser. Vehicle shut

This could be related to a loose camshaft drive belt. If you have slack in the belt the camshaft will rebound on over run causing the P0340. It can also be a Crackshaft sensor problem too.(P0335) Hope this helps...

Posted on Mar 06, 2011

  • 15 Answers

SOURCE: 2002 pt cruiser Camshaft Sensor

change the crankshaft positon sensor in the rear of the engine above the oilfilter. Also check the wiring to this sensor, they have a problem shorting out. You have to change the camshaft and crankshaft sensors at the same time. Make sure you give your car a major tune up. Did you check yor starter?.........runjoe

Posted on Mar 04, 2009

  • 15 Answers

SOURCE: code 344 camshaft sensor ciurcut intermitint 05 pt cruiser

check you tps sensor throttle postion sensor

Posted on Jun 03, 2009

  • 412 Answers

SOURCE: 2002 PT Cruiser fuel pump and filter

FUEL PUMP IS LOCATED IN FUEL TANK..FILTER IS LOCATED ON TOP OF PUMP MODULE..A NEW PUMP WILL NORMALLY COME WITH THIS FILTER..YOU MUST REMOVE FUEL TANK FROM VEHICLE TO REPLACE THESE COMPONENTS..IF YOUR NOT SURE YOU CAN DO THIS,I WOULD TALK TO A REPAIR SHOP..FUEL CAN BE VERY DANGEROUS

Posted on Jun 23, 2009

  • 819 Answers

SOURCE: Camshaft sensor malfunction...code 0340.

i believe it is on the drivers side end of the head, accesable from the top.

Posted on Nov 13, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 pt cruiser p0118 code came up, replaced the sensor and still showing up


Is there 2 Sensor's on your Car?

One for the Gauge and one for the Computer?

Apr 10, 2013 | 2007 Chrysler PT Cruiser Touring Hatchback

2 Answers

2008 pt cruiser - check engine light came on, within minutes it started to "power down" and and died. Won't start. What could cause this? BTW have changed spark plugs, camshaft sensore, cranks


My PT did that when my timing belt broke. It cost $500.00 to replace it. If it is broken, be ready to have some motor work done. I had to have to values replaced at a cost of $900.00. If your timing belt is not broken then check the alternator and battery. I was riding down the road and my PT shut all the way down and would not start. I had to leave it beside the road. It was my alternator. It gave me no warning.

Dec 04, 2012 | 2008 Chrysler Pt Cruiser

1 Answer

PT cruiser engine warning


P0344 is camshaft Position sensor,Dont get confused with the camshaft sensor, You have a timing problem and your solution is the timing belt.

Jun 26, 2012 | 2006 Chrysler PT Cruiser

1 Answer

Got code po340 on 2008 Chrysler PT cruiser. Runs great sometimes when engine light on & rough at other times like not getting gas. Engine light does not come on every day either. Cam sensor or timing...


P0340: Camshaft Position Sensor A - Bank 1 Circuit Malfunction

- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty Camshaft Position Sensor
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery

Feb 08, 2012 | 2008 Chrysler Pt Cruiser

1 Answer

2002 PT Cruiser. Vehicle shut down while driving. Received P0340 Trouble code..No camshaft position sensor signal at pcm. I replaced Position Camshaft Sensor, book suggests life on these 5-10 years, It...


This could be related to a loose camshaft drive belt. If you have slack in the belt the camshaft will rebound on over run causing the P0340. It can also be a Crackshaft sensor problem too.(P0335) Hope this helps...

Mar 06, 2011 | 2003 Chrysler PT Cruiser

1 Answer

Car wont start...i was told it was the crank sensor...not sure where its located...


This no start could be alot of things. This car has a timing belt on the engine. If this belt breaks the engine won't start and it will spin over faster than normal. When this happens it will normally set a camshaft sensor code but that is because the camshaft is not turning because the timing belt is broken. Hope this helps, Tommy

Sep 21, 2010 | 2005 Chrysler PT Cruiser

1 Answer

Timing belt problem


when you broke the belt you most likely broke the magnet for the cam sensor. What you need to do is spin the engine around to TDC and look for a magnet.

Take the sensor out first.

Jan 16, 2010 | 2002 Chrysler PT Cruiser

2 Answers

2002 pt cruiser replaced camshaft position sensor still not starting wires are good


if you replace the crank sensor and camshaft sensor you need a DRB scan tool reprogram sensor to pcm.so they will work.

Dec 06, 2009 | 2002 Chrysler PT Cruiser

1 Answer

2002 pt cruiser Camshaft Sensor


change the crankshaft positon sensor in the rear of the engine above the oilfilter. Also check the wiring to this sensor, they have a problem shorting out. You have to change the camshaft and crankshaft sensors at the same time. Make sure you give your car a major tune up. Did you check yor starter?.........runjoe

Feb 04, 2009 | 2002 Chrysler PT Cruiser

Not finding what you are looking for?
2002 Chrysler PT Cruiser Logo

879 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6876 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...