Question about 1998 Chevrolet Cavalier

1 Answer

What type of connection is between catalytic converter and exhaus

Engine type 2200

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 121 Answers

Should be two bolt flange with "spring bolts" at manifold, and slip fit connection at center pipe with 2" saddle clamp. If that's what your asking. Hope this helps

Posted on Nov 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are the catalytic converters located


There are only two catalytic converters. They are of a high efficiency type and as such, they are tucked on each side of the engine directly bolted to the exhaust manifolds. You won't see them easily from underneath the car as you would on most vehicles. Item #1 and #11 in the diagram below are the catalytic converters.
03c556e4-acc6-484a-b125-549ef12834df.png

Sep 18, 2014 | 2002 Jaguar X-Type

2 Answers

Is $2200 a fair price to replace catalytic converter in a 2001 Sienna with 118,000 miles on it?


I would say that a factory replacement could be that high, but a muffler shop should be able to fit a universal aftermarket for much less.

Aug 09, 2014 | Cars & Trucks

1 Answer

2003 dodge catalytic converter


What code you have did try to reset.

Apr 09, 2013 | Dodge Caravan Cars & Trucks

1 Answer

Check engine


Check engine light means a sensor or electronic component is bad in your vehicle. If vehicle runs fine, it usually is the O-2 sensor located by your exhaust system close to motor, or by catalytic converter or in exhause pipe before cat. take to autozone, advance auto or orielly's. Test is free.

Jan 17, 2013 | 2012 Jeep Grand Cherokee

2 Answers

I have an 1998 Chevy Blazer and need to change the catalytic converter, are the flange bolts welded and can i cut them


Catalytic Converter Removal & Installation 2.2L Engine To Remove:
Catalytic converter 2.2L engine gm-03-22-734.gif

  1. Raise and safely support the vehicle.
  2. Disconnect the heated oxygen sensor (HO2S) electrical connector.
  3. Remove the exhaust manifold pipe flange mounting nuts from the catalytic converter.
  4. Remove the catalytic converter flange mounting nuts from the muffler.
  5. Remove the catalytic converter from the muffler.
  6. Remove the catalytic converter from the rear hanger bracket insulator.
  7. Remove the catalytic converter.
  8. Remove the (HO2S) from the catalytic converter.
To Install:
  1. Install the (HO2S) to the catalytic converter.
  2. Install a new gasket and the catalytic converter to the muffler.
  3. Install catalytic converter to the catalytic converter hanger.
  4. Install the catalytic converter flange mounting nuts to the muffler flange.
    • Tighten to 26 ft lbs (35 Nm).
  5. Install the catalytic converter flange mounting nuts to the exhaust manifold pipe flange.
    • Tighten to 26 ft lbs (35 Nm).
  6. Connect the heated oxygen sensor (HO2S) electrical connector.
  7. Lower the vehicle.
------ Catalytic Converter Removal & Installation 4.3L Engine To Remove:
  1. Raise and safely support the vehicle.
  2. Raise and support the transmission.
  3. Remove the transmission support
  4. Disconnect the left and right pre-converter heated oxygen sensor (HO2S) electrical connector.
  5. Disconnect the post-converter (HO2S) connector. Muffler flange and gasket gm-03-43-731.gif

  6. Remove the catalytic converter flange mounting nuts from the muffler.
  7. Remove the catalytic converter from the muffler.
  8. Remove the exhaust manifold flange mounting nuts from the catalytic converter. Catalytic converter 4.3L engine gm-03-43-735.gif

  9. Remove the catalytic converter from the support bracket insulator.
  10. Remove the catalytic converter and gaskets.
  11. Remove the heated oxygen sensor.
To Install:
  1. Install the heated oxygen sensors as needed.
  2. Install a new gasket and the Install the catalytic converter to the support bracket insulator.
  3. Install the catalytic converter to the exhaust manifold flange. Install the mounting nuts.
    • Tighten to 39 ft lbs (53 Nm).
  4. Using a new flange gasket, install the catalytic converter to the muffler. Install the mounting nuts.
    • Tighten to 30 ft lbs (40 Nm).
  5. Connect the left and right pre-converter heated oxygen sensor (HO2S) electrical connectors.
  6. Connect the post-converter (HO2S) electrical connector.
  7. Install the transmission support.
  8. Lower the transmission.
  9. Lower the vehicle.
prev.gif next.gif ---
It looks like you can cut them and replace them with new bolts and nuts.prev.gif next.gif

Sep 05, 2010 | 1998 Chevrolet Blazer

1 Answer

Where is the oxygen sensor on 1997 ford taurus wagon 3.0


Single or double overhead cam type engine? In any case, these are the locations listed below.
  • Up-stream sensor (located before catalytic converter)
  • Left up-stream sensor (located before catalytic converter)
  • Left down-stream sensor (located after catalytic converter)
  • Right up-stream sensor (located before catalytic converter)
  • Right down-stream sensor (located after catalytic converter)

May 04, 2010 | 1997 Ford Taurus

1 Answer

Catalytic Converter for Honda CRV 2002- cost/necessity of repair


run scanner for trouble codes, some auto parts stores will do this for free

Oct 09, 2009 | 2002 Honda CR-V

3 Answers

Catalytic converter my service engine soon light on my 2006 infinity m35x came on the car runs smooth however iam told i need to replace the converter i have 140000 miles which takes me out of warranty...


Take the car to a muffler shop (not to one of the big national chains).

They will replace it for around $50~$70 and not charge for additional services like the big muffler shops.

They will keep the old catalytic converter (it has platinum in it).

Your exhause pipe may "smoke" and smell stinky a bit for after few hours of driving.


Sep 14, 2009 | 2006 Infiniti M35

1 Answer

I need to replace the catalytic converter


may be some have them coming off the exhause manifolds

Jan 18, 2009 | 1998 Mitsubishi Montero Sport

1 Answer

High idaling , exhause pipes turning orange red under motor, not converter


Sound as though you have a lean burn condition and this is usually caused from a vacuum leak and that is what I would check for first.What engine is in it?
JIM

Sep 23, 2008 | 2002 Ford Escape

Not finding what you are looking for?
1998 Chevrolet Cavalier Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...