Question about 2001 Chevrolet Tahoe

4 Answers

2001 Chevy Tahoe with ABS & Brake light on.

I have a 2001 Chevy Tahoe with the ABS & Brake light on.The Electro-Hydraulic Control Unit runs continuosly. Do you have any suggestions?

Posted by on

  • 7 more comments 
  • chrismodule Dec 02, 2008

    My ABS light is on and the module is running. I went under the truck and dis connected the module wires. Now the traction control light stays on, as well as the ABS light. The part is very expensive, so I've been driving without ABS brakes and traction control. Is there a more cost effective fix.

  • Anonymous Jan 12, 2009

    I have a 2001 Tahoe ABS and Brake light that comes on when it warms up, what could this be?

  • geeza10 Mar 07, 2009

    same problem, after this winter in new england the abs brakes were utilized a few times. i dont know much about cars, now the abs light and brake light come on soemtimes.

  • phantom1125 Dec 09, 2012

    Just unplug the fuse, you'll maintain traction control and save your battery. If you replace the fuse, the Electro-Hydro-Cont-Unit will run and you will have ABS.

  • phantom1125 Dec 09, 2012

    Just remove the fuse. You can put it in when you go for a grive. Or get it fixxed.

  • phantom1125 Dec 09, 2012

    ^for a DRIVE!!! Ha!

  • Anonymous Mar 17, 2014

    Brake lights came on and brakes are low]

  • Anonymous Mar 18, 2014

    light stays on while driving

  • Anonymous Mar 23, 2014

    NO BRAKE PROBLEMS

×

4 Answers

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I hope you have the problem fixed by now, but, it is the ABS control under the truck. You need to go under the hood and open the fuse box and disconnect the 60 amp fuse for the ABS, this will turn it off before it burns up. This however will also cause the traction assist off light to stay lit all the time. To the fix the problem you can pay tons of money ($700 or so) to have the dealership install a ABS control and the problem will happen again over time. Or, remove it yourself, go on ebay and ship it off to a guy who repairs them for about $150 and you will never have the problem again. Also, if you wrap your cable ends with plastic and protect them good, you can still drive you truck while the part is being worked on. It takes about a week.

Posted on Nov 24, 2008

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I have a 2004 s10 4X4 and my abs ligth comes on after a while. The brakes work fine and I found no difference. Can you tell me if a sensor is bad or what may be the problem? Thank you

Posted on Mar 22, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chevrolet Master
  • 71,694 Answers

Have you checked to see if the control relay is stuck closed?

Posted on Nov 12, 2008

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

On 2001 Chevy Tahoe the ABS lite comes on after I start moving. Sometime the brake lite will come on as well

Posted on Feb 02, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On a 2004 chevy tahoe instrument cluster,the parking brake light is red. Is that due to the overlay or a red bulb.


Possibly the ABS unit, look in your owners manual for the ABS fuse (it's under the hood) unplug it with the key on, shut off key and replug, if the light go's out drive it, the light will probably come back if it does you need a ABS control unit.

Feb 18, 2017 | Cars & Trucks

2 Answers

2002 Tahoe abs relay location


images for 2002 Tahoe abs relay location

Chevy ABS and Brake Dash Light fix - YouTube

? 24:15
https://www.youtube.com/watch?v=Jo76ylqgUR8
Dec 22, 2012 - Uploaded by Skizzot7
This is how to fix intermittent ABS and Brake dash lights on all Chevrolet ... That board is rather robust and is installed external to the vehicle in a location that sits .... I took the module out of a2002 Sierra and it is engineered with no T10 .... ABS Sensor and Harness 2000-06 Chevy Suburban Tahoe GMC ...

How I fixed a Chevy with an Abs and Brake light on - YouTube

images for 2002 tahoe wiring



Dec 09, 2015 | Cars & Trucks

1 Answer

2001 chevy venture van the brake pedal is soft and it goes down to the floor is it the m/c or the abs unit


The symptom you have is caused by a defective Master cylinder. Bench bleed the master before installing to keep air out of the ABS hydraulic control unit, if air gets in the unit the car will need to bleed of air using a special tool at the dealer. Do not get brake fluid on any painted surfaces or in your eyes, use proper safety gear. Only use special tubing Flare nut wrenches on the brake line fittings or you will round them off. Making up new lines is a whole other thing that requires special skills and tools.

Sep 21, 2011 | Chevrolet Venture Cars & Trucks

1 Answer

ABS light on. Abs pump continues to run after engine shutoff. Where is the 60 amp fuse, so I can remove and continue to use my 2001 Chevy Tahoe. Also, can I get the abs module fixed instead of having to...


The fuse should be in the under hood fuse panel.The other thing you can do is disconnect the power wire to the ebcm.The ebcm is located on the passengers side below the drivers door area.Just unplug the 2 wire connector.It is the red and a black wire.About 10 gauge.The top part of this unit is the electronic brake control module and it is the cause of the motor running continuously.The problem is that water gets in to this and shorts out the unit.There are only 4 torx screws that hold this on but they are not easy to get at and sometimes they strip.I believe it is a number 20 torx bit.Hope this helps.Good luck.

Nov 07, 2010 | Chevrolet Tahoe Cars & Trucks

1 Answer

I have a 2001 gmc sonoma 4.3 replace brake lines on back i am not getting any fluid to rear wheels i tryed bleeding sys with help diconected abs sys to reset to defalt no abs light is on stumped


a special tool is required to hold the ABS hydraulic control unit popit valves open during bleeding of the brakes, without this special tool you will not be able to get the air out of the system, most good brake shops have this tool or of course the local Chevy dealer or GMC dealer. I am a dealer tech and know this information is correct..

May 12, 2010 | 2001 GMC Sonoma Extended Cab

1 Answer

Anti lock brake pump always running and noisy


If the ABS pump continues to run, the most common cause is a leak in the hydraulic control unit. The pump may continue to run in order to to try to maintain operating pressure. Also a malfunction in the pump, stuck valves and devective accumulators are possible causes. A shorted pressure switch may also cause this condition.

Jul 09, 2009 | 2001 Chevrolet Tahoe

1 Answer

Abs sensor light wont go off my 2005 polo


Your ABS systems use a combination of electronic and hydraulic systems to modulate the brakes individually to prevent them from locking up. ANTILOCK systems consist of wheel speed sensors, a hydraulic control unit (HCU), and an electronic control unit (ECU). Because of how complex the system is your computer does a self-test. If the check is successful, the ANTILOCK and BRAKE lights will go out within a few seconds. If one of the component of the ABS system fails to pass one or both lights will remain lit. One or both warning lights may also come on while driving, also indicating a problem. If just the ANTILOCK warning light comes on, some ABS component has failed, but the car still has hydraulic brakes. The grinding noise could the the ABS pump or your brake pads could to worn to the metal backing and grinding against the brake rotors. I recommend a inspection soon for your safety.

Mar 04, 2009 | Audi S4 Cars & Trucks

1 Answer

2001 Mercury Grand Marquis brake and ABS dash lights on and off


The red brake light is the key here. That usually indicateds a hydraulic problem. Check you fluid level in master cylinder and see if it is low. Also the level indicator sensor there in the master cylinder maybe sticking or corrioded. If ABS sees the red brake light it will shut off and turn on the ABS light,also traction control would be disabled as well.

Feb 04, 2009 | 2001 Mercury Grand Marquis

1 Answer

ABS and Brake Light comes on.


driver side rear view mirror turned yellow

Jan 02, 2009 | 1996 Subaru Legacy

Not finding what you are looking for?
2001 Chevrolet Tahoe Logo

7,003 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

71694 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22082 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7031 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...