Question about Daewoo Nubira

2 Answers

Car engages in gear without clutch pedal down and car will not drive daewoo matiz

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

It wont go into gear at all

Posted on Apr 08, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 275 Answers

If it wont drive how do you kno its engaging if it is in gear and you arent pushing in the clutch it should move forward if it doesnt move then you will have to replace the clutch

Posted on Nov 12, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I just put a new slave cylinder and clutch master cylinder on a 2003 Honda accord 3.0 V6 six speed and you can shift the gears without the clutch pedal pushed in or the car started


that is normal if the gear synchro dogs ( teeth) are in line in the box
problems concerning a clutch are
slashing gears when trying to engage first or reverse with the pedal to the floor ---needs bleeding
slipping when the clutch pedal is released--- slipping clutch from the pressure not being released ---problem in master cylinder
reverse gear is the only gear not synchronised so even with the clutch depressed it is possible sometimes that it will not go into gear unless you let the clutch up to move the gears in the box then attempt to re-engage reverse

May 04, 2016 | Honda Cars & Trucks

1 Answer

Vehicle dies when downshifting to first gear and also makes a squeling noise


Manual Transmission

  1. 1
    Park your car with its front tyres touching the curb. Engage 1st and start slowly releasing the clutch pedal without applying any throttle. The engine should gradually fade out and bog down when the pedal is completely released. If the engine just bogs down at some point, or the fading is not gradual, the clutch is damaged. If the gearbox grinds when you try to shift in first from a standstill, there's a damage in the clutch too.
    550px-find-out-if-a-transmission-has-gone-out-step-1.jpg


  2. 2
    Try to pull off in 3rd gear with the front wheels at the curb, and without applying throttle. If the engine doesn't die, it shows a complete clutch failure. In that case, do not drive this vehicle.
    550px-find-out-if-a-transmission-has-gone-out-step-2.jpg
  3. 3
    Find a smooth, straight road to test the vehicle. Start from first, and slowly accelerate from second. As you do this use late-shifting, i.e. slightly over-rev the engine (approx. 500-1000 RPM faster than the revs you'd normally shift at). Up-shift to second without using double-clutching. Repeat the same procedure when shifting into 3rd. Now, with your car running at approximately 50 km/h (25 mph) try down-shifting to second without double-clutching. Both the up-shifting and the down-shifting must be done without grinding. Grinding of the gears indicates a gearbox malfunction, most likely in the sync gears ("synchronizers"). To make sure it's the synchronizers, try up-shifting and down-shifting with double-clutching. If the grinding stops, then it's the synchronization.
    550px-find-out-if-a-transmission-has-gone-out-step-3.jpg
550px-find-out-if-a-transmission-has-gone-out-step-4.jpg
  • 2
    Shift into drive and hold the break pedal after making sure your brakes work. Press the gas pedal all the way down. The engine should not fade. If it does, it means the transmission (particularly the clutch) does not disengage completely.
    550px-find-out-if-a-transmission-has-gone-out-step-5.jpg
  • 3
    Check for smooth shifting. On an even and relatively horizontal road you should be able to accelerate without any tangible jolts. If there are such, the gearbox has malfunctioned.
    550px-find-out-if-a-transmission-has-gone-out-step-6.jpg
  • 4
    Check for vibrations. Driving at about 70 km/h (35 mph) switch to Neutral (both auto and manual). There shouldn't be any lateral vibrations. If there are, this is either due to a warping of the drive-shaft, or a suspension damage. Basically, drive-shaft warping is perceived as a vibration in both vertical and horizontal direction, whereas a suspension damage is felt as a vibration in only one direction (i.e. either horizontally or vertically).
    550px-find-out-if-a-transmission-has-gone-out-step-7.jpg
  • 5
    Test steering. When trying to enter a corner with approximately 30 km/h (15 mph) there shouldn't be any tangible under-steer. The presence of such may be due to a differential failure, especially in FWD cars. Novice drivers must never try and test their differentials by trying to induce under/over-steer!
    550px-find-out-if-a-transmission-has-gone-out-step-8.jpg
  • EditTips for preventing transmission damages

    • Avoid prolonged driving by slipping the clutch.
    • Avoid jerks and jolts while driving.
    • Avoid "riding the clutch", i.e. needlessly keeping your foot on the clutch pedal.
    • Never use clutch slipping for regulating the speed of a heavy truck!
    • Make sure the clutch of a manual transmission is fully pressed when shifting
    • Do not use excessive force when shifting a manual.
    • For rear wheel drive (RWD) vehicles, avoid driving through places at the minimum of the vehicle's clearance.
    EditTips

    • Incomplete disengaging is due to the trailing disc sticking to the leading one, e.g. because of mechanical soiling of the friction surfaces or worn out springs.
    • Incomplete disengaging in automatic transmissions is felt as a forward jolt when the gearbox changes gears, whereas incomplete engaging is felt as over-revving the engine without any significant change in speed, especially when stepping on the throttle at high speeds (over 50 km/h or 30 mph).
    • Automatic transmissions have the so-called "hydraulic clutch". It's basically a combination of a hydraulic pump, driven by the engine, and a hydraulic motor, linked to the rest of the drive-train. This allows for the hydraulic liquid to flow through the motor, even if its load is too big for the engine to rotate it. This eases operation, but results in poorer acceleration, greater fuel consumption and severely decreased ability of the driver to use engine braking, which can be very dangerous on long downward slopes. Hydraulic clutches are easier to operate in urban driving, but become a drawback on long roads
    • Gearboxes come in three types: manual, semi-automatic, and automatic
    • Malfunctions in a hydraulic clutch include incomplete disengaging (due to old hydraulic fluid, which has become thicker than specified by the manufacturer), or incomplete engaging (most often due to a leak of hydraulic fluid or presence of an air pocket within the hydraulic circuit. These are both dealt with by replacing the hydraulic fluid, bleeding (if necessary) of the hydraulic system, and removing any possible leaks.
    • The most common malfunction of a dispatch box is the inability to change its function (e.g. switch between 4x2 and 4x4) If this happens, refer to a repair shop.
    • The clutch is designed to smoothly disconnect the engine from the rest of the drive-train.
    • The clutch disengaging too low or too high is an indication of a worn out trailing disc.
    • There are implements that allow an automatic gearbox to operate in semi-automatic mode, allowing the driver to manually shift gear up or gear down, but w/o using a clutch. These operate exclusively by aids of electronics. This is common in high-class German cars like the S-Klasse Mercedes. Usually the corresponding position of the lever is marked with T or M and the driver selects a gear down by moving the lever to the left, and a gear up by nudging it do the right.
    • Semi-automatic gearboxes are combined with a hydraulic clutch. They allow the driver to select a gear up or a gear down. These are most often seen in rally cars, where there are two levers on both sides of the steering wheel. Usually the right one switches a gear up, and the left one switches a gear down.

    Aug 23, 2013 | 1995 Suzuki Sidekick

    2 Answers

    I have 11 year old Daewoo matiz SG car. Run only 72000km. Now the problem is if switch on the AC , the car will not take lod if travel four peoples if the car in First gear also can not able to drive. The...


    Did you ever check your spark plug. Change all 4 and your high tension wire might also defective. If your already done this procedure then your clutch might be worn out. This mean your clutch is sliding. Or your engine need tune up means need adjustment on the valve inside the engine

    Sep 08, 2011 | Daewoo Lanos Cars & Trucks

    1 Answer

    How do you replace a clutch cable to a daewoo matiz


    Hi, it must be done from underneath (unless you remove the entire engine), hoist up the car and work from underneath.
    Drain Gear box oil.
    Remove wheels, disconnect bolts and swing out wheel hubs, remove CV Joint drive shafts (both sides).
    Disconnect two get change levers
    Disconnect clutch cable.
    Then replace it with the new one ...

    Take care

    Jul 27, 2010 | 2002 Daewoo Lanos

    2 Answers

    99 dodge avenger gears will not engage


    if it happen all of a sudden then its most likely the clutch slave cylinder.

    Dec 07, 2009 | Dodge Avenger Cars & Trucks

    1 Answer

    I have a 1998 accord 4cyl coupe manual trans. The


    A clutch issue youtend to have more of an engagement problem with 1st and reverse gear for a small time period before you notice other gears.You want to check the clutch hydrolic system for any leaks(clutch slave at transmission,clutch master,which you look for leakage on interior above clutch pedal)and at fluid resevoir.you also want to double check condition of trans fluid. strongly recommend using only HONDA BRAND MANUAL TRANS. FLUID when doing maintinance,fluid should be replaced every 30k on this car.The Honda brand fluid is like night and day on these cars,it WILL make a difference in shifting!!TRust Me on this point! Sorry now back to your main clutch issue,when driveing and you go to shift gears and normally notice grinding,with clutch pedal in shft out of gear and before engageing it into next gear do a double pump of clutch pedal then see if when continuing to next gear if it engagees smoother.if so you know you have without a dout a clutch pressure plate/disc problem. I can tell you that in twenty years the only manual transmissions themselves that ever had problems were due to outside influences(gear oil in transmission,improper driveing,etc.)let me know what you find and we can go from there..JOEL

    Oct 17, 2009 | 1998 Honda Accord

    2 Answers

    2004 daewoo matiz se - Truoble getting in first gear.


    It may be the synchro of the first gear.  It may have been worn out.  To check, you may try to put it in 2nd gear before putting it into first to be sure.

    Jun 08, 2009 | 2002 Daewoo Nubira

    1 Answer

    Trouble changing gears 1st and 2nd


    If the clutch feels firm with no play u may have worn syncronizer's in the trans, take it to trans shop and have them road test it, they will not charge in most cases.

    Jan 21, 2009 | 2002 Daewoo Nubira

    4 Answers

    Car will not drive, is it clutch or cabel


    my daewoo lanos wont shift into gear/s while running even when clutch is depressed all the way

    Nov 12, 2008 | 2001 Daewoo Lanos

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    418 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Daewoo Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    yadayada
    yadayada

    Level 3 Expert

    60769 Answers

    Steve Hurc
    Steve Hurc

    Level 3 Expert

    450 Answers

    Are you a Daewoo Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...