Question about 1996 Lexus LX 450

1 Answer

My car want start. it is not getting fire to the sparkplungs.

I install spark plungs,spark plung wires distriberter cap,rotor,ignition coil,and a control module. in still there no fire getting to the sparkplungs can anyone help me with this problem.the car just turning over put not starting. and i am running out of money. well ran out of money

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

See if the check engine lite comes on when ignition is turned on if it dose'nt lite check fusable links @ batteries pos. terminal , then check EFI fuses.If good try swapping EFI relay with one of same part # behind driver's side kick panel tempararly to test.Other than that you can check to see if distributor rotor is turning with cap off when starter is engaged.If that checks good you probably have a primary circuit / triggering malfunction. [ Crank , Cam sensors, & or Igniter problem] Hope this helps

Posted on Feb 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

It mayI have no fire going to the coil or from the coil to the plugs


Have you checked the wiring, the spark @ plug, Power to the coil???

Engine Won't Start No Spark - Auto Diagnosis Repair Help

aa1car.com/library/no_spark.htm
If your engine cranks normally but will not start because it has no spark, or it ... If an engine has a coil-on-plug ignition system with no plug wires, remove one of ...

No-start, No-Spark diagnosing simulated - YouTube

? 5:13
https://www.youtube.com/watch?v=XSWN1M8Hoqo
May 19, 2010 - Uploaded by FrankHurtAuto
Simulation of no start with no spark diagnosing, ... Ignition coiland module test with test light (ScannerDanner Premium lecture) - Duration: ...

getting fire from coil but not to plugs - CarGurus

www.cargurus.com > Questions > Dodge > Ram 1500

CarGurusJun 12, 2013 - 2000 dodge ram 1500 4x4 not getting fire changed distributor cap, coil, pickup ignition, rotor, plugs, plug wires 2 answers. ... 1994 dodge 5.9 just shut off and wont start back up there is no spark or fire from coil or plugs. ... 94 dodge van 318 eng will not start new plugs new crank ...

Ignition Coil Troubleshooting: (No) Fire in the Hole

www.secondchancegarage.com/public/coil-troubleshooting.cfm

Jan 27, 2016 | Cars & Trucks

1 Answer

Y is my 97 chevy only fires on the number one cylender


if you have fire on the number one cylinder,it means that the ignition coil is working so your problem can come from spark plug wire or cap and rotor . unplug the wire from ignition coil to distributor and check for fire you are suppose to have fire because you saying having fire on cylinder one. from there change cap of distributor and rotor plus a set a spark plug wire.

Oct 07, 2014 | Chevrolet Silverado 1500 Cars & Trucks

3 Answers

Ignition mystery! 1994 GMC Suburban 2500 5.7 mtr. No spark to spark plugs. Have spark from coil to distributor. Have changed coil wire, cap, rotor, ignition module, and coil. have 12.5 volts going to...


I guess you could have the ignition analyzed on an oscilloscope. Maybe a tech could see something then.
I always heard the only gap was the spark plug gap-the rotor has no gap-are you sure you got the correct rotor? And does it touch the top distributor cap coil wire tower?

Let us know. It is a mystery worthy of a solution.

Sep 21, 2013 | Chevrolet Suburban 2500 Cars & Trucks

3 Answers

I have a 1993 chev pick-up v6 4.3, i just installed new spark plugs,new plug wires, distributor cap and rotor button.All plug wires are back in the right position,and i used the firing order 1-6-5-4-3-2...


This diagram is for 1998-1995 Chevy 6 cylinder 4.3L engines.
Your got the firing order exactly correct, at 1-6-5-4-3-2, but here's the thing to double-check:
The distributor rotation is clockwise (note badly rendered arrow in picture).



archaeology_96.jpg

Since you probably got everything right, then you're left with really unusual/rare causes of
failure of the ignition system:
(a) rotor button misaligned/failing to make contact?
(b) rotor button not pressed onto distributor shaft far enough therefore failing to provide correct
proximity to distributor cap contacts when coil fires
(c) coil wire or contact loose/disconnected - press coil wire firmly down into distributor cap.
(d) distributor shaft of other damage caused during installation of rotor.
(e) spark plug wires defective from factory
(f) spark plugs defective from factory
(g) battery low - may need a charge to start
(h) ICM (ignition control module) failure - hook up your HEI (high energy ignition) tester, and
watch the quality of the spark on each cylinder.
(i) fuel problem? If spark is being properly delivered, its gotta be a fuel problem...
(j) distributor cap not screwed down flush to top of distributor? maybe just on one side?

Inspect the inside of the distributor cap - if there are lots of little metal bits all over the inside
of the distributor cap, then you know you have a misalignment of some type in there, and the
rotor and cap are destroying each other. normal operation will throw a quota of spark-ed off
metal bits inside the distributor cap, but since your cap is brand new, your attempts to start
the engine should have rotated the distributor so few times, you should see no metal debris.

Inspect the distributor cap contacts to see if any spark marks are more of less in the middle
of the cap's proper "contact zone". If not, you've diagnosed an internal misalignment, which
you know how to correct.

Sep 14, 2011 | Chevrolet 1500 Cars & Trucks

1 Answer

Would crank but would not start in extremely cold weather. Now it won't start at all but fires on and off.


Do a tune-up, Plugs, rotor button and distributor cap. Not sure if your model has a cap or coil pack. When you say fires off and on do you mean it starts off and on or you get ignition spark off and on. If you have a cap, the rotor button can get worn down and not make good contact with the contacts inside the cap. When engine rotates the rotor button rotates inside the cap which produces spark through your plugs wires. If you have a coil pack, it could be going bad. If coil packs get moisture within it and diffuses the spark from going into the plug wires. Moisture and wetness causes a lot of problems with the ignition system, so it's best to apply Di-Electric Grease to the coil pack, wire boots on both ends. The grease stops moisture from getting into the components and sparks from jumping to the moisture.

Jan 17, 2010 | 1994 Honda Accord

1 Answer

1997 jeep cherokee 4l will not start on petrol or lpg


Here are a couple of things that could be causing your problem. 1. Bad ignition coil or ignition module 2. Clogged fuel filter 3. Clogged air filter 4. Clogged fuel injectors 5. Bad spark plugs, wires, distributor cap and /or rotor. 6. Broken timing chain/belt. Here are a few things you can try to verify that you have a good spark. 1. Remove the distributor cap and crank the car. If the rotor turned you're ok. If it doesn't turn then that's you're problem and you will probably need to change a timing belt/chain. 2. Check the spark from the ignition coil by pulling the coil wire from the center of the distributor. Use an alligator clip to attach a short wire to the coil wire contact. Bare the other end of this short wire and set it up so it's sitting very close to the engine block. Turn off the lights and try to start the car. You should see a spark jump from this wire to the block. If you don't see a spark it's likely your ignition module or ignition coil is bad. 3. If you have a spark maybe it's not getting to the plugs. You may need to replace the distributor cap and rotor. You can test if the plugs are sparking by pulling one, re-attaching the spark plug wire and seeing if you get a spark when you try to start the engine in the dark. Please note, the metal threads of the spark plug need to be shorted to the engine block to complete the circuit during this test.

Jun 06, 2009 | 1998 Jeep Cherokee

Not finding what you are looking for?
1996 Lexus LX 450 Logo

Related Topics:

222 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...