Question about 1995 Ford F250

1 Answer

Clutch--after market versus original, 95,5spd 7.3 ltr diesel

Truck needs new clutch, what is the difference bet. after market and original, are there any special tools needed to replace clutch..

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 26 Answers

Go with a Centerforce 1 clutch kit. Check their website centerforce.com. It's worth every penny!

It's a chunk of change but so is having to replace the clutch every 40,000 miles or less.

Posted on Nov 12, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does any one know what compression should read on 2 ltr diesal passat engine code cba in psi please


VW diesel engines have a spec of 360-450 psi with new engines. It is only considered a bad engine if the reading is below 276 or there is a difference of more than 73 psi between cylinders.

Aug 03, 2016 | Cars & Trucks

1 Answer

How much does it cost to replace a clutch on 1987 nissan pulsar


clutches cost $700.0 plus original, around $500 after market ( (original equipment in a different box) and the labour costs depend on if the flywheel needs surfacing Time will be around 6 hours at local labour time rate.
Are you sure it is the clutch as problematic master cylinders will make a clutch slip
Get a second opinion from an accredited clutch specialist before you spend money.

Feb 26, 2015 | Nissan Cars & Trucks

1 Answer

How to replace the master and slave clutch cylinder


must bet the sport sidekick as all G16 engine sidekicks are cable.
the J18 engine, has hyd. clutch/
see here
remove them, , put in new,
bleed it. same as with simple brakes, no different.
J18 SPORT.
http://www.fixkick.com/tranny/clutch/clutch-on-kick.html#sport

Jun 24, 2014 | 1997 Suzuki Sidekick

1 Answer

1998 dodge ram clutch locked up put a new compressor and clutch on now im getting no power to the compressor any suggestions


Model? engine? gas ? diesel? fuse "J" under the hood............. you really need to be specific, as different models have different wiring.

Aug 04, 2011 | 1999 Dodge Ram

1 Answer

So, i have a Tracker that has been changed, by the previous owner, from factory auto trans to a 5 speed. It has an issue with the engine (bogs) and the gauges (go haywire), when you run/ shift into gear....


Hi, the wiring is certainly different as the automatic has shift and TCC solenoids that the manual does not have. The safety interlock is also different--on the clutch pedal for manual versus the trans range sensor on the auto. Also, the backup light switch is separate on the manual versus integrated to the range switch on the auto. The speed sensor may be different or the same, I'm not sure. Now, the real difference in the drivability is that the auto trans is controlled by the PCM, and the data is fed back to the PCM for proper engine operation. If the previous owner didn't change the computer, then the algorithms in the computer are not optimized for a maunal transmission. I'm not sure that is the reason for your problems. Can you find out if the PCM in the car is the original versus a replacement for a manual transmission?

Jan 20, 2011 | 1998 Chevrolet Tracker

2 Answers

When pushing down the pedal, the gears and pto is grinding more and more as time goes by. I adjusted the clutch pedal , but no help. Can this problem be fixed by a shade tree mechanic or do I need to take...


I am not a diesel mechanic, a tractor mechanic, or a shade tree mechanic. But, it sounds to me like it is time for a new clutch pack. Anyone with reasonable knowledge of simple mechanics can do this job at a much cheaper price than a professional diesel or tractor mechanic, but it can be a heavy duty job. I would weigh the differences in downtime of my equipment and the ability of my shade tree mechanic.

Jul 24, 2010 | 1983 Ford Ranger

1 Answer

Clutch assy repair ,car has 210 mm disc -stores have 22o mm disc


Check with a reputable Honda dealer. A 10mm difference might not be that inconvenient. These after-market parts do meet or exceed the OEM (original equipment manufactured)

Oct 21, 2009 | 2000 Honda Accord

1 Answer

I have water in fuel problem. 6.5 ltr turbo diesel


you can try drygas or seafoam at your local auto parts store.

May 26, 2009 | 1995 Chevrolet C2500

Not finding what you are looking for?
1995 Ford F250 Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

71231 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...