Question about Mitsubishi Galant

2 Answers

Does a left-rear shock absorber no longer attached to the unibody, with no attachment hardware being left up top that I can see signal a prohibitively expensive repair - or did the mounting hardware which normally holds the top of the shock to the car simply rust away and fall off, with replacement of both the mounting hardware and shock being fairly straightforward? This is a '94 Galant LS with some corrosion underneath, but with what appears to be a fairly sound round hole into which a new bracket could be mounted... Thanks in advance for your ideas!

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 121 Answers

The hole that you refer to would have held the upper strut mount. This piece is part of the strut assembly which includes the coil spring. If you attempt the replacement of this mount yourself, it will require the use of a coil spring compressor (clamshell type which you can rent from certain auto parts stores or tool rental centers). You will have to remove the complete strut assembly from the car. In your case, what's left is the lower retaining bolt. You'll have to use great caution when compressing the spring in order to remove the nut that holds the upper mount in place. The spring is under a great deal of preloaded pressure, that if released can cause bodily damage. Once you remove the upper nut, you can replace the mount, or mounting plate itself. If you don't want to tackle this job yourself. I can tell you that the typical shop will charge you around 2 hrs labor to replace this part. (hourly rates vary) The cost of parts is extra naturally. Most shops I've worked for won't install parts other than those purchased through the shop. You may get lucky though. Buying your own parts is always cheaper, because you don't have to pay for the mark up. I hope this helps.

Posted on Nov 12, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 185 Answers

This sounds like an extensive repair. Without seeing a picture of the hole its kinda hard to tell. Most of your shocks will need a mounting kit anyway. I think if you were going to do this yourself you would be best to go ahead and buy the shock and mounting kit and put it in yourself and if that turns out to be a no go for you at least you have the parts to send along with the car to the repair shop (hence saving you some bucks there anyway). Good luck to you hope this helps.

Sincerely,

JC

Posted on Nov 12, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The Magnum wobbles and has a rattling noise when you go over any little thing.


Loose and worn suspension,because it wobbles,this say upper bearing plate that is attached to the front struts,when a upperbearing plat is worn it can no longer support the load, It is the load carrier of the vehicle, in return why it went out is mainly a shock absorber, shock absorber are fluid filled charged cartridge and when worn it can no longer absorb road shock,you need a front strut both front and a inspection of the upperbearing plate which is part of the strut.

Apr 26, 2011 | Dodge Magnum Cars & Trucks

1 Answer

How to replace the rear shocks on a 1998 nissan maxima


REMOVE REAR SEAT AND PACKAGE SHELF TO GAIN ACCESS TO THE UPPER SHOCK ATTACHING NUTS.REMOVE UPPER ATTACHING NUTS. RAISE VECHICLE REMOVE REAR WHEEL AND SUPPORT THE LOWER CONTROL ARM WITH A JACK REMOVE LOWER SHOCK ABSORBER MOUNTING BOLT. REMOVE SHOCK ABSORBER ASSEMBLY FROM THE VECHICLE. COMPRESS THE COIL SPRING WITH THE PROPER SPRING COMPRESSOR TOOL. REMOVE CENTER RETAINING NUT HOLDING THE UPPER MOUNTING INSULATOR. SLOWLY DECOMPRESS THE COIL SPRING.REMOVE THE MOUNTING INSULATOR AND THE COIL SPRING. REMOVE THE COIL SPRING. TO INSTALL COMPRESSED COIL SPRING ONTO THE STRUT ASSEMBLY. BE SURE TO THE END OF THE SPRING IS IN THE NOTCH ON THE LOWER SEAT.INSTALL UPPER MOUNTING INSULATOR. YOU WILL NEW LOCKNUT FOR THE CENTER RETAINING NUT OF THE COIL SPRING. CENTER RETAINING NUT AND TORQUE THE NUT TO 13 TO 17 FT LBS. SLOWLY REMOVE THE SPRING COMPRESSOR TOOL. INSTALL SHOCK ABSORBER ASSEMBLY IN THE VECHICLE AND INSTALL THE MOUNTING FASTERNERS AND TORQUE LOWER MOUNTING BOLTS TO 72 - 87 FT LBS. INSTALL WHEEL.LOWER VECHICLE. WARNING COIL SPRING UNDER EXTREME LOADS WHEN COMPRESSED.BESURE TO PROPERLY ALIGN THE SPRING WITH THE COMPRESSING TOOL TO PREVENT PERSONAL INJURY FROM THE SPRING RELEASING UNEXPECTEDLY.

Feb 02, 2011 | 1998 Nissan Maxima

1 Answer

I need to remove the entire passenger side rear suspension. Does it go through the trunk or the back seat? If so how do you remove the back seat?


REMOVAL & INSTALLATION 1983-86 Models
  1. On 4-door sedan, remove the package tray and vent duct.
  2. On hatchback, remove the speaker grilles.
  3. Disconnect the brake line from the wheel cylinder. CAUTION
    Brake fluid contains polyglycol ethers and polyglycols. Avoid contact with the eyes and wash your hands thoroughly after handling brake fluid. If you do get brake fluid in your eyes, flush your eyes with clean, running water for 15 minutes. If eye irritation persists, or if you have taken brake fluid internally, IMMEDIATELY seek medical assistance.
  4. Remove the brake line from the brake hose.
  5. Disconnect the brake hose from its bracket on the shock absorber.
  6. Loosen, but do not remove, the nut holding the suspension support to the shock absorber.
  7. Unbolt the shock absorber from the rear arm.
  8. Unbolt and extract the shock absorber from the body. To install:
  9. Attach the shock absorber to the body and tighten the 3 nuts to 17 ft. lbs. (25 Nm).
  10. Engage the shock absorber bracket with the carrier and install the hardware. Tighten the nuts to 119 ft. lbs. (162 Nm).
  11. Tighten the center suspension support nut to 36 ft. lbs. (49 Nm). There is a bearing located under the suspension support dust cover. Remove the dust cover and pack the bearing with multi-purpose grease. Once packed, reinstall the dust cover.
  12. The remainder of installation is the reverse of removal. Tighten each component to specifications.
  13. Have the rear wheel alignment checked.
1987-88 Models
  1. On wagon models, remove the toneau cover holder.
  2. Loosen the rear wheel lug nuts, raise the rear of the vehicle and support it safely. Block the front wheels.
  3. Remove the rear wheels.
  4. Using the proper size flare nut wrench, disconnect the backing plate hardware.
  5. With a flare nut and a back-up wrench, disconnect the brake tube from the brake hose and use a small plastic container to collect the brake fluid.
  6. Undo the clip and disconnect the brake hose from the shock absorber. NOTE: Before the axle bolts are removed, the axle carrier must be supported with a jack.
  7. Support the axle carrier with a floor jack and remove the mounting bolts and nut. Disconnect the axle carrier from the shock absorber.
  8. Support the shock absorber firmly by hand and remove the three mounting nuts. Remove the shock absorber from the body. To install:
  9. Position the shock absorber onto the body and support it firmly by hand. Install the three nuts and tighten them to 23 ft. lbs. (31 Nm).
  10. Attach the axle carrier to the shock absorber with the nuts and bolts. Tighten the nuts to 166 ft. lbs. (226 Nm).
  11. The remainder of installation is the reverse of removal. Tighten each component to specifications.
  12. Bleed the brake lines as described in Section 9.
  13. Have the rear wheel alignment checked.
1989-96 Models
  1. On the 4-door sedan, remove the package tray and vent duct. On 1992-96 models, it will be necessary to remove the rear seat back.
  2. On the hatchback, remove the speaker grilles.
  3. On the wagon models remove the tonnue cover and rear seat back.
  4. Loosen the rear wheel lug nuts, raise the rear of the vehicle and support it safely. Block the front wheels.
  5. Remove the rear wheels.
  6. Disconnect the brake hose and the ABS speed sensor from the shock absorber.
  7. If equipped with ABS, disconnect the Load Sensing Proportioning Valve (LSPV) spring from the lower arm.
  8. Disconnect the stabilizer bar link from the shock absorber.
  9. Support the rear axle and loosen the 2 bolts from the lower end of the shock absorber.
  10. From inside the vehicle, unbolt the upper support. Fig. 1: A rubber cap covers the rear shock absorber tower nut 89558p01.jpg
    Fig. 2: The upper shock absorber tower is retained by the center nut (circled) and three surrounding nuts 89558p02.jpg

  11. Lower the rear axle carrier and remove the two bolts.
  12. Remove the shock absorber from the vehicle. To install:
  13. Install the shock absorber assembly onto the vehicle.
  14. Connect the brake hose and the ABS speed sensor to the shock absorber.
  15. Connect the stabilizer bar link to the shock absorber.
  16. Install the wheel and tire assembly.
  17. During installation, please observe the following tighten specifications:
    1. Tighten the shock absorber-to-body bolts to 29 ft. lbs. (39 Nm).
    2. Tighten the shock absorber-to-axle carrier nuts to 166 ft. lbs. (226 Nm) on 1988-91 vehicles and 188 ft. lbs. (255 Nm) on 1992-96 vehicles.
    3. Tighten the suspension support-to-shock absorber nut to 36 ft. lbs. (49 Nm) on 1988-91 vehicles. On 1992-96 models, tighten the stabilizer bar link to shock absorber retainers to 47 ft. lbs. (64 Nm).
  18. Install the rear seat back, vent duct and the package tray as required.
prev.gif next.gif

Dec 18, 2010 | 1986 Toyota Camry

1 Answer

How do you replace shocks on 1991 buick skylark


REMOVAL & INSTALLATION Fig. 1: After you open the trunk lid, use a suitable prytool to remove the trim cover 86888036.jpg
Fig. 2: Some vehicles have a cover which must be removed to access the shock retaining nuts 86888037.jpg
Fig. 3: Unfasten the upper shock attaching nuts 86888038.jpg
  1. Disconnect the negative battery cable.
  2. Open the trunk lid and remove the trim cover. If equipped, remove the nut cover.
  3. Remove the upper shock attaching nut(s). If removing both shocks, remove one at a time.
  4. Raise and safely support the vehicle.
  5. Unfasten the lower shock absorber mounting bolts. One wrench will have to be placed on the bolt head side to retain the bolt as you loosen the nut. Usually a 15mm wrench is used to remove them. To install: Fig. 4: After the vehicle is raised and safely supported, use a socket to unfasten the lower retaining bolt 86888039.jpg
    Fig. 5: Remove the retaining bolt, then . . . 86888040.jpg
    Fig. 6: . . . remove the shock absorber assembly from the vehicle 86888041.jpg
  6. Connect the shock absorbers at the lower attachment and install the attaching bolt.
  7. Lower the vehicle enough to guide the shock absorber upper stud through the body opening, then fasten the upper shock absorber attaching nut loosely. Tighten the lower shock absorber mounting bolt to 35 ft. lbs. (47 Nm).
  8. Remove the axle support, then carefully lower the vehicle. Tighten the shock absorber upper nut to 21 ft. lbs. (29 Nm).
  9. If equipped, install the retaining nut cover, then install the rear trim cover. Close the trunk lid.
  10. Connect the negative battery cable.
prev.gif next.gif

Oct 08, 2010 | Buick Skylark Cars & Trucks

1 Answer

Need new struts on rear, Would like to replace with air shocks. Any suggestions on how I would do this?


Shock Absorber -The rear already has air shocks on the 1999 Cadillac Deville: REMOVAL & INSTALLATION Rear
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Rear wheel Fig. 1: Exploded view of the rear shock absorber mounting 9300vg06.gif

    • Negative battery cable
    • Shock absorber electrical connector from the rear suspension support, If equipped
  3. Support the lower control arm with a jack to relieve the tension on the shock absorber.
  4. Remove or disconnect the following:
    • Lower shock absorber mounting bolt and nut
    • Upper mounting nut, retainer, and insulator
    • Shock absorber compress by hand and remove through the upper control arm
    To install:
  5. Position the top of the shock absorber with the insulator attached into the suspension support.
  6. Install or connect the following:
    • Upper shock insulator, retainer and nut. Torque the nut to 55 ft. lbs. (74 Nm).
    • Shock absorber lower mounting nut/bolt. Torque the nut to 75 ft. lbs. (102 Nm).
    • Shock absorber electrical connector to the rear suspension support, if equipped
    • Rear wheel
    • Negative battery cable
prev.gif next.gif

Jul 29, 2010 | 1999 Cadillac DeVille

1 Answer

Do i have to remove the back seat to take rear struts off


Answer
REMOVAL - SHOCK ASSEMBLY
NOTE: Access for the nuts attaching the rear shock assembly upper mount to the vehicle is through the inside of the trunk.

Roll back carpeting on top of the rear shock tower to access shock mounting nuts.
Remove plastic cover from the top of the shock assembly.
Remove 2 nuts attaching the shock assembly upper mount/spring seat to the shock tower.
Raise vehicle on jackstands or centered on a frame contact type hoist. (Refer to LUBRICATION & MAINTENANCE/HOISTING - STANDARD PROCEDURE)
Remove the rear wheel and tire assembly from the vehicle.
Remove two fasteners holding the splash shield to the shock assembly upper mount.
Remove bolt attaching shock absorber to rear knuckle (Shock Absorber Attachment To Knuckle).
Remove the shock absorber from the rear knuckle first when removing the shock absorber from vehicle by pushing down on the rear suspension.
Move shock assembly downward and tilt top of shock outward, then remove shock assembly from vehicle through top of wheel opening

Nov 23, 2009 | 2002 Dodge Stratus

1 Answer

I have a 94 jeep wrangler front left axle seal bad. I took the left side apart and not sure how to get the seal back in. Do I need to open the inspection cover on the diff. and take the gears out?



Rear Axle Notes
  1. Raise and support vehicle.
  2. Remove rear wheels.
  3. Scribe alignment marks on propeller shaft and axle for proper assembly, then disconnect propeller shaft from axle.
  4. Disconnect the track bar from axle mounting bracket.
  5. Disconnect parking brake cable at equalizer.
  6. Disconnect shock absorbers at axle tubes.
  7. Disconnect hydraulic brake hose at rear axle Tee-fitting, then tape ends of hose and fitting to prevent contamination.
  8. Disconnect axle vent tube from axle.
  9. Remove U-bolts and tie plates.
  10. Loosen spring mounting bolts.
  11. If equipped, disconnect ABS wiring connections at axle.
  12. Support axle with suitable jack.
  13. Remove spring-to-shackle attaching bolts and lower spring to the floor.
  14. Remove axle assembly.
  15. Reverse procedure to install.

Front Axle Notes
  1. Raise and support vehicle at frame behind front springs.
  2. Remove front wheels.
  3. Scribe alignment marks on propeller shaft and axle yoke for proper assembly, then disconnect propeller shaft at axle yoke.
  4. Disconnect connecting rod at steering knuckles.
  5. Disconnect shock absorbers at axle housing.
  6. Remove stabilizer bar connecting links to spring tie plates attaching bolts, if equipped.
  7. Disconnect breather tube at axle housing.
  8. Disconnect stabilizer bar link bolts at spring clips.
  9. Remove disc brake calipers, rotors and brake shields.
  10. Remove U-bolts and tie plates.
  11. Support axle assembly with suitable jack to relieve spring tension.
  12. Loosen rear spring shackle to spring attaching bolts.
  13. Remove front spring shackle to spring attaching bolts and lower spring to floor.
  14. Remove axle from under vehicle.
  15. Reverse procedure to install.

Jul 21, 2009 | 1994 Jeep Wrangler

1 Answer

I need to know how to get to the rear suspension (tower)


i don't think you have to do any repairs from the top end. I will list most fromFord shop manual. Please rate as Fixya if this answers your questions. Please report back. Good luck.

Section 04-02: Suspension and Wheel Hubs, Rear 1994 Town Car, Crown Victoria/Grand Marquis. Workshop Manual
REMOVAL AND INSTALLATION Spring Rear
Removal
  1. Position a hoist under the rear axle housing, and raise the vehicle. Refer to Section 00-02 . Place jackstands under frame side rails.
  1. Remove rear stabilizer bar as outlined.
  1. Disconnect the lower studs of the two shock absorbers from the mounting brackets on the rear axle assembly .
  1. Unsnap the RH parking brake rear cable and conduit (2A635) from RH upper arm retainer before lowering the rear axle assembly .
  1. Lower the hoist and axle housing until the rear springs are released.
  1. Remove rear spring and rear spring center mounting insulators (5741) from vehicle.
    -----------------------------------------------------------------
Shock Absorber Removal
Raise the vehicle on a hoist. 1. To assist in removing the upper attachment on shock absorbers using a plastic dust tube, place an open end wrench on the hex stamped into the dust tube's metal cap. For shock absorbers with a steel dust tube, simply grasp the tube to prevent stud rotation when loosening the retaining nut.
  1. Remove the shock absorber retaining nut, washer, and insulator assembly from the stud on the upper side of the frame. Discard nut. Compress the shock absorber to clear the hole in the frame, and remove the inner insulator and washer from the upper retaining stud.
  2. Remove the self-locking retaining nut, and disconnect the shock absorber lower stud from the mounting bracket on the rear axle tube.
  3. Perform Shock Absorber Checks. Refer to Section 04-00 to determine shock absorbers performance.
Installation
  1. Properly prime the new shock absorber . Refer to Section 04-00 , Shock Absorber Checks.
  1. Place the inner washer and rear spring insulator (5536) on the upper retaining stud, and position the shock absorber so that the upper retaining stud enters the hole in the frame. While holding the shock absorber in this position, install a new rear spring insulator , washer and nut assembly on the upper side of the upper frame. Be sure to seat the rear spring insulator in the frame attaching hole. Tighten nut to 34-46 Nm (25-34 lb-ft).
  1. Extend the shock absorber , and place the lower stud in the mounting bracket hole on the rear axle assembly housing. Install a new self-locking retaining nut. Tighten nut to 76.5-103.5 Nm (56-76 lb-ft).
  1. Lower vehicle.
-----------------------------------------------------------------------------
Arm Lower
Removal
Refer to the illustration in Description and Operation. NOTE: To improve rear axle assembly noise and vibration concerns, the rear suspension should be fastened to the frame and rear axle assembly at the curb height position.
NOTE: If one rear suspension lower arm requires replacement, also replace the opposite rear suspension lower arm .
sra~us~en~file=ani_caut.gif~gen~ref.gif WARNING: TURN REAR SUSPENSION LEVELER COMPRESSOR SWITCH OFF (IF SO EQUIPPED).
NOTE: If both rear suspension arm and bushings and both rear suspension lower arms are to be removed at the same time, remove both rear springs as outlined under Rear Spring Removal. For air spring removal, refer to Section 04-05 .
  1. Mark rear suspension shock absorber relative to protective sleeve with the vehicle in a static, level ground condition.
  1. Remove rear stabilizer bar as outlined.
  1. Raise the vehicle on a hoist, and place jackstands under the rear axle assembly . Refer to Section 00-02 .
  1. Lower the hoist until the shock absorbers are fully extended to relieve rear spring pressure.
  1. Support rear axle assembly under differential pinion nose as well as under rear axle assembly .
  1. Remove and discard the lower arm pivot bolt and nut from the axle bracket. Then, disengage the rear suspension lower arm from the bracket.
  1. Remove and discard the pivot bolt and nut from the frame bracket, and remove the rear suspension lower arm .
-----------------------------------------------------------------
Upper
Removal
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Suspension Bushing Service Set T79P-5638-A1, A2 and A5 Rear Axle Control Arm Bushing Tools T86P-5638-AH
sra~us~en~file=ani_caut.gif~gen~ref.gif WARNING: TURN OFF REAR SUSPENSION LEVELER COMPRESSOR SWITCH (IF SO EQUIPPED).
  1. Raise the vehicle, and support the frame side rails with jackstands. Refer to Section 00-02 .
  2. Support the rear axle assembly .
  3. Lower the rear axle assembly , and support the rear axle assembly under differential pinion nose as well as under rear axle assembly .
  4. Unsnap parking brake rear cable and conduit from upper arm retainer.
  5. Remove and discard the nut and bolt retaining the rear suspension arm and bushing to the rear axle assembly housing. Disconnect the rear suspension arm and bushing from the housing.
  6. Remove and discard the nut and bolt that secures the rear suspension arm and bushing to the frame bracket, and remove the rear suspension arm and bushing . If upper arm rear bushing is to be replaced, use Suspension Bushing Service Set T79P-5638-A and Rear Axle Control Arm Bushing Tools T86P-5638-AH and the following procedure:
  7. Place the upper arm rear bushing remover tool in position, and pull bushing out. Using Suspension Bushing Service Set T79P-5638-A install bushing assembly into bushing ear of rear axle assembly.
------------------------------------------------
Stabilizer Bar
sra~us~en~file=ani_caut.gif~gen~ref.gif WARNING: TURN OFF REAR SUSPENSION LEVELER COMPRESSOR SWITCH (IF SO EQUIPPED).
Removal
  1. Raise vehicle on hoist, and place jackstands under the frame side rails. Refer to Section 00-02 .
  1. Lower the hoist and rear axle assembly housing until the shock absorbers are fully extended.
  1. Disconnect rear stabilizer bars from rear stabilizer bar link and bushing (5C488) . Remove bolts and stabilizer bar bracket (5486) retaining rear stabilizer bar to rear axle assembly .

Mar 05, 2009 | 1994 Lincoln Town Car

1 Answer

Shocks


rear
5955ba5.gif ------------------------------------------------------------------------------------------

front

Removal
  1. Remove front shock absorber-to-upper shock bracket nut and bolt.
  1. Disconnect the lower end of the front shock absorber bolt and nut from the U-bolt plate.
  1. Compress the front shock absorber and remove.
Installation
  1. Insert front shock absorber into the front shock absorber mounting bracket (18183). Insert bolt and tighten nut to 60-81 Nm (45-60 lb-ft).
  1. Attach the lower end of the front shock absorber to the U-bolt plate by installing the nut and bolt. Tighten to 60-81 Nm (45-60 lb-ft).
---------------------------------------------------------------------------------------------

front


Feb 04, 2009 | 1996 Ford F350 Crew Cab

1 Answer

2004 dodge stratus SE


This is a dangerous job if you do not have the proper equipment for compressing the spring that is around the rear shock. I do not recomend performing this job without the proper equipment. Unloading the spring without it compressed can cuase injury.

If you have the proper equipment this is how you do it.

REMOVAL - SHOCK ASSEMBLY NOTE: Access for the nuts attaching the rear shock assembly upper mount to the vehicle is through the inside of the trunk.
  1. Roll back carpeting on top of the rear shock tower to access shock mounting nuts.
  2. Remove plastic cover from the top of the shock assembly.
  3. Remove 2 nuts attaching the shock assembly upper mount/spring seat to the shock tower.
  4. Raise vehicle on jackstands or centered on a frame contact type hoist.
  5. Remove the rear wheel and tire assembly from the vehicle.
  6. Remove two fasteners holding the splash shield to the shock assembly upper mount.
  7. Remove bolt attaching shock absorber to rear knuckle
  8. Remove the shock absorber from the rear knuckle first when removing the shock absorber from vehicle by pushing down on the rear suspension.
  9. Move shock assembly downward and tilt top of shock outward, then remove shock assembly from vehicle through top of wheel opening.

Aug 04, 2008 | 2004 Dodge Neon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

302 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...