Question about 2006 Cadillac SRX

2 Answers

Replacing front turn signal bulb on 2006 Cadillac SRX

I need a diagram on how to replace the fron turn signal bulb on a 2006 Cadillac SRX. Or detailed instructions.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

You must take the front wheel off, then remove the inner front fender panels (2), they are fastened with plastic pushbuttons. this exposses the light housings for the turn and fog lambs. This takes about an hour, but saves you alot of money.

Posted on Feb 19, 2013

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
  • tekcomp Nov 22, 2008

    Hopes the shed some light to your problem.

×

2 Suggested Answers

  • 3 Answers

SOURCE: Replacing front turn signal bulb on 2006 Cadillac SRX

wow i feel sorry for you because Cadillac designed this bulb to be a don't get to bulb but OK here's what you do take the bottom cover off or skid plastic panel under neath the front end theirs little plastic clips holding it on just get come dikes and don't cut them but just use it to help pull them out. after you get that off use a flash light and locate your light housing you should see two screws holding the house in i think those screws are 8mm i cant remember remove those two screws and be careful the metal from the bumper cuts you pull the light housing out and remove all the screws around the housing and open the housing up replace the bulb and make sure your contact to the bulbs clean and then reassemble the way you took apart. if you cant get it well then best bet is take it somewhere i know Cadillac charges an arm and a leg so you can go somewhere else.

Posted on Jan 25, 2009

  • 4 Answers

SOURCE: Replacing front turn signal bulb on 2006 Cadillac SRX

WikiAnswers
http://wiki.answers.com/Q/How_to_change_the_Cadillac_SRX_Front_Tun_Signal_Bulb

Posted on Feb 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 cadillac srx fixing or replacing light bulbs rear license plate


You might be able to access it if you stick your hand up inside the rear of the bumper.

Nov 26, 2015 | 2008 Cadillac Srx

1 Answer

How to change front turn signal bulb on 2008 SRX Cadillac


Nope don't need to drop the whole light assembly. I just took the wheel and inner cover off, then the 6 torx screws that hold the light hosing together , replaced the turn signal bulb and good to go!!

Mar 04, 2013 | 2004 Cadillac SRX

1 Answer

How do i replace the fuse for the front turn signal on 2006 cadillac srx


The socket is defective?? Probe the socket with a volt meter to see if voltage is turning on and off to trigger the bulb to flash.

Jul 09, 2012 | 2006 Cadillac SRX

1 Answer

Change turn signal bulb 2008 srx


Front turn signal bulb replacement 2008 SRX . Jack up car & block . Remove front wheel & front half of the wheel house assemble. There are about 7 plastic pull rivets that have to be removed . Pull out the wheel house . Remove turn signal & driving light cover held on by 6 # T10 torx screws . Twist out socket & replace bulb # 3757NAK . Should take about 45 min.

Mar 26, 2012 | 2006 Cadillac SRX

1 Answer

Need to replace front turn signal bulb on a 2004 Cadillac SRX


need to remove front wheel and panel from the inside.
almost the entire wheel cover need to come off

Aug 04, 2010 | 2004 Cadillac SRX

3 Answers

I need to change the left front turn signal bulb on a 2006 Cadillac SRX? Looks difficult. Paul LeMaster


hi Paul

Should be able to open the hood remove plastic headlight cover & pull pins (2) on light assembly whole light assembly will pull out then replace turn signal.

Good luck.

Dec 02, 2009 | 2006 Cadillac SRX

4 Answers

Replacing front turn signal bulb on 2006 Cadillac SRX


wow i feel sorry for you because Cadillac designed this bulb to be a don't get to bulb but OK here's what you do take the bottom cover off or skid plastic panel under neath the front end theirs little plastic clips holding it on just get come dikes and don't cut them but just use it to help pull them out. after you get that off use a flash light and locate your light housing you should see two screws holding the house in i think those screws are 8mm i cant remember remove those two screws and be careful the metal from the bumper cuts you pull the light housing out and remove all the screws around the housing and open the housing up replace the bulb and make sure your contact to the bulbs clean and then reassemble the way you took apart. if you cant get it well then best bet is take it somewhere i know Cadillac charges an arm and a leg so you can go somewhere else.

Nov 13, 2008 | 2004 Cadillac SRX

Not finding what you are looking for?
2006 Cadillac SRX Logo

1,632 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...