Question about 1997 Ford Explorer AWD

1 Answer

What is an "actuator"? And what can I do about it?

Posted by on

  • need 411 Nov 12, 2008

    This sight is SO helpful. I got a very quick response (to a couple different questions). I am going to try the advice tomorrow. THANK YOU SO MUCH!!!

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 393 Answers

It is what locks and unlocks the doors. you can try to spray some lubricant or rust buster on them by putting window down and spraying towards the rear of door. once you get door open you need to remove door panel to gain access to the assemblies .

Posted on Nov 12, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the door blend actuator on 2009 lincoln mks


Right side or left ? Electronic Automatic Temperature Control or manual ? Temperature or mode door ?
Temperature Blend Door Actuator - LH Removal and Installation
NOTE: It is not required to install the new LH temperature blend door linkage parts included in the LH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.
LH temperature blend door actuator and linkage
  1. Remove the 2 lower steering column opening cover bolts.
  1. Detach the lower steering column opening cover.
  1. Disconnect the in-vehicle temperature sensor aspirator hose and electrical connector.
  1. Position the instrument panel wire harness away from the LH temperature blend door actuator.
  1. Remove the 3 LH temperature blend door actuator screws.
  1. Disconnect the LH temperature blend door actuator electrical connector.
  1. Remove the LH temperature blend door actuator.
  1. Manually operate, and inspect the LH temperature blend door linkage for incorrect placement, binding or damage.
Temperature Blend Door Actuator - RH, Dual-Zone EATC Removal and Installation
NOTE: It is not required to install the new RH temperature blend door linkage parts included in the RH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.
RH temperature blend door actuator and linkage
  1. Disconnect the glove compartment damper from the glove compartment.
  1. Remove the glove compartment.
  1. Remove the RH lower instrument panel insulator.
  1. Remove the RH lower floor console trim panel.
  1. Remove the 3 RH temperature blend door actuator screws.
  1. Disconnect the RH temperature blend door actuator electrical connector.
  1. Remove the RH temperature blend door actuator.
  1. Manually operate, and inspect the RH temperature blend door linkage for incorrect placement, binding or damage.
  2. Mode Door Actuator - Defrost/Panel/Floor Door
  3. Removal and Installation
    NOTE: The defrost/panel/floor mode door actuator can be accessed from below the driver side of the instrument panel.
    NOTE: It is not required to install the new defrost/panel/floor mode door linkage parts included in the defrost/panel/floor mode door actuator service part kit if only the mode door actuator requires replacement and the linkage parts are not broken or binding.
    Mode door actuator and linkage
    1. Remove the 3 defrost/panel/floor mode door actuator screws.
    1. Disconnect the defrost/panel/floor mode door actuator electrical connector.
    1. Remove the defrost/panel/floor mode door actuator.
    1. Manually operate, and inspect the defrost/panel/floor mode door linkage for incorrect placement or damage.
    Mode door actuator linkage only
    1. Remove the mode door linkage.
      1. Depress the tab and remove the panel door lever.
      1. Remove the floor/defrost door intermediate lever screw and floor/defrost door intermediate lever.
      1. Pull straight outward to remove the floor/defrost door lever.
    Mode door actuator and linkage
    1. NOTE: When installing the mode door actuator, make sure that the panel door lever and floor/defrost intermediate lever are correctly aligned with the mode door actuator cam.
      To install, reverse the removal procedure.

Nov 10, 2016 | 2009 Lincoln MKS

1 Answer

Where is the blend door actuator located on a 2007 Pontiac Grand Prix


! Pontiac doesn't call it a blend door actuator .
There are Air Temperature Actuator - Left : Air Temperature Actuator - Right
Mode Actuator Recirculation Actuator Now if you would state the problem your having , we could tell you what to do , need to take dash apart or the glove box needs to come out . Do you have automatic or manual HVAC system .
Air Temperature Actuator The air temperature actuator is a 2-wire bi-directional electric motor. Two control circuits enable the actuator to operate. The control circuits use either a 0-volt or 12-volt value to co-ordinate the actuator movement. When the actuator is at rest, both control circuits have a value of 0 volts. In order to move the actuator, the HVAC control module grounds the appropriate control circuit for the commanded direction. The HVAC control module reverses the polarity of the control circuits to move the actuator in the opposite direction.
The HVAC control module determines the door position by counting motor pulses on one of the control circuits. These pulses are small voltage fluctuations that occur when the brush is shorted across 2 commutator contacts as the motor rotates. As the actuator shaft rotates, the HVAC control module monitors the voltage drop across an internal resistance to detect the pulses. The HVAC control module converts the pulses to counts with a range of 0-255 counts. The HVAC control module uses a range of 0-255 counts to index the actuator position.

May 29, 2016 | Cars & Trucks

2 Answers

I have codes b0428 and B3532 coming up . I just need to know what the problem may possibly be and what might I do to fix it ?


Code B0428 is for the rear temp actuator.
Code B3532 is for the rear mode actuator for the HVAC unit

May 19, 2016 | 2006 Chevrolet Chevrolet Uplander

1 Answer

Temp light flashes when car start up. turn on heater and blows cold air on passenger side, and barely warm on driver side. No blowing air from defroster. Will work occasionally but usually it is this...


Air Door Actuators/Motors Removal & Installation Recirculation Actuator 1996 - 1999 1996 - 1999 HVAC Actuators gm-10-00-1840.gif

To Remove:
  1. Remove the left sound insulator panel.
  2. Disconnect the vacuum hose from the recirculation actuator.
  3. Remove the recirculation actuator from the valve.
To Install:
  1. Connect the recirculation actuator to the valve.
  2. Clip the recirculation actuator to the air inlet.
  3. Connect the vacuum hose to the recirculation actuator.
  4. Install the left sound insulator panel.
2000 - 2005 2000 - 2005 Recirculation Actuator gm-10-00-1559.gif

To Remove:
  1. Remove the instrument panel compartment.
  2. Remove the right sound insulator.
  3. Remove the dash integration module from the bracket.
  4. Remove the 2 dash integration module bracket fasteners and position the bracket to gain access to the recirculation actuator.
  5. Disconnect the electrical connector from the recirculation actuator.
  6. Remove the recirculation actuator.
To Install:
  1. Install the recirculation actuator and torque the fasteners to 12 in-lbs (1.4 Nm).
  2. Connect the electrical connector to the recirculation actuator.
  3. Install the dash integration module bracket and torque the fasteners to 12 in-lbs (1.4 Nm).
  4. Install the dash integration module into the bracket.
  5. Install the right sound insulator.
  6. Install the instrument panel compartment.
  7. Recalibrate the actuator.
Defroster Valve Actuator 1996 - 1999 1996 - 1999 HVAC Actuators gm-10-00-1840.gif

To Remove:
  1. Remove the air distributor assembly.
  2. Unclip the defroster valve actuator from the air inlet.
  3. Disconnect the defroster valve actuator from the valve.
To Install:
  1. Disconnect the defroster valve actuator from the valve.
  2. Clip the defroster valve actuator from the air inlet.
  3. Install the air distributor assembly.
Heater/Bi-Level Actuator 1996 - 1999 1996 - 1999 HVAC Actuators gm-10-00-1840.gif

To Remove:
  1. Remove the air distributor assembly.
  2. Remove the clip and the screws that fasten the 2 halves of the air distributor assembly and separate the air distributor assembly.
  3. Unclip and disconnect the heater/bi-level actuator from the valve.
To Install:
  1. Connect and clip the heater/bi-level actuator to the valve.
  2. Fasten the 2 halves of the air distributor assembly together and torque the fasteners to 13 in-lbs (1.5 Nm).
  3. Install the air distributor assembly.
Temperature Actuator 1996 - 1999 1996 - 1999 HVAC Actuators gm-10-00-1840.gif

To Remove:
  1. Remove the instrument panel assembly.
  2. By snapping the rod out of the valve, remove the temperature valve link rod from the temperature valve.
  3. Disconnect the electrical connector from the temperature actuator.
  4. Remove the temperature actuator.
To Install:
  1. Install the temperature actuator and torque the fasteners to 12 in-lbs (1.4 Nm).
  2. Connect the electrical connector to the temperature actuator.
  3. Start the vehicle.
  4. Set the fan to position to high.
  5. Set the temperature to full hot.
  6. Allow a minimum of 45 seconds for the temperature valve actuator to move to the full hot position.
  7. Move the temperature valve to the full hot position.
  8. Snap the temperature valve link rod into the temperature valve.
  9. Install the instrument panel assembly.
Mode Actuator 2000 - 2005 Mode and Left Air Temperature Actuator gm-10-00-1560.gif

To Remove:
  1. Remove the left side sound insulator panel.
  2. Remove the knee bolster.
  3. Remove the instrument panel cluster. (Automatic HVAC)
  4. Disconnect the electrical connector from the left air temperature actuator. (Automatic HVAC)
  5. Remove the left air temperature actuator. (Automatic HVAC)
  6. Disconnect the electrical connector from the mode actuator.
  7. Remove the mode actuator.
To Install:
  1. Align the mode door levers with the cam slots.
  2. Install the mode actuator and torque the fasteners to 12 in-lbs (1.4 Nm).
  3. Connect the electrical connector to the mode actuator.
  4. Install the left air temperature actuator and torque the fasteners to 12 in-lbs (1.4 Nm). (Automatic HVAC)
  5. Connect the electrical connector to the left air temperature actuator. (Automatic HVAC)
  6. Install the instrument panel cluster. (Automatic HVAC)
  7. Install the knee bolster.
  8. Install the left side sound insulator panel.
  9. Recalibrate the actuators.
Left Air Temperature Actuator 2000 - 2005 Mode and Left Air Temperature Actuator gm-10-00-1560.gif

To Remove:
  1. Remove the left side sound insulator panel.
  2. Remove the knee bolster.
  3. Remove the instrument panel cluster.
  4. Disconnect the electrical connector from the left air temperature actuator.
  5. Remove the left air temperature actuator retaining screws.
  6. Remove the left air temperature actuator.
To Install:
  1. Install the left air temperature actuator and torque the fasteners to 12 in-lbs (1.4 Nm).
  2. Connect the electrical connector to the left air temperature actuator.
  3. Install the instrument panel cluster.
  4. Install the knee bolster.
  5. Install the left side sound insulator panel.
  6. Recalibrate the actuators.
Air temperature Actuator (Manual), Right Air temperature Actuator (Automatic) 2000 - 2005 Right Air Temperature Actuator gm-10-00-1561.gif

To Remove:
  1. Remove the instrument panel compartment.
  2. Disconnect the electrical connector from the air temperature actuator.
  3. Remove the right air temperature actuator.
To Install:
  1. Install the air temperature actuator and torque the fasteners to 12 in-lbs (1.4 Nm).
  2. Connect the electrical connector to the air temperature actuator.
  3. Install the instrument panel compartment.
  4. Recalibrate the actuators.
prev.gif next.gif

Nov 03, 2010 | 1998 Buick LeSabre

1 Answer

P1109 error code


DTC P1109 Secondary Port Throttle System

Did you get a subcode?
-0F Swirl Actuator Malfunction
-08 Swirl Actuator Supply Voltage Range/Performance
-05 Swirl Actuator Feedback Circuit High Voltage
-02 Swirl Actuator Feedback Circuit Low Voltage
-29 Swirl Actuator Feedback Signal Malfunction
-28 Swirl Actuator Feedback Signal Malfunction
-21 Swirl Actuator Feedback Signal Range/Performance
-54 Swirl Actuator Feedback Powerstage High Temperature

Oct 29, 2010 | 2004 Saab 9-3

1 Answer

Ac blowing heat on side and air on the other side.


Air Door Actuators Removal & Installation Console Mode To Remove:
  1. Remove the center console from the vehicle.
  2. Detach the air outlet duct from the center console.
  3. Disconnect the console mode actuator connector.
  4. Detach the console mode actuator from the center console.
To Install:
  1. Attach the console mode actuator to the center console. Torque the screws to 17 in-lb (1.9 Nm).
  2. Connect the console mode actuator connector.
  3. Attach the air outlet duct to the center console. Torque the screw to 17 in-lb (1.9 Nm).
  4. Install the center console into the vehicle.
Left Side Air Temperature To Remove:
  1. Remove the instrument panel carrier from the instrument panel.
  2. Disconnect the left side air temperature actuator connector. HVAC control module - left side gm-10-00-1844.gif

  3. Detach the left side air temperature actuator from the HVAC module.
To Install:
  1. Attach the left side air temperature actuator to the HVAC module. Torque the screw to 17 in-lb (1.9 Nm).
  2. Connect the left side air temperature actuator connector.
  3. Install the instrument panel carrier onto the instrument panel.
  4. Recalibrate the left side air temperature actuator.
Right Side Air Temperature To Remove:
  1. Remove the instrument panel carrier from the instrument panel.
  2. Disconnect the right side air temperature actuator connector.
  3. Detach the right side air temperature actuator from the HVAC module.
To Install:
  1. Attach the right side air temperature actuator to the HVAC module. Torque the screw to 17 in-lb (1.9 Nm).
  2. Connect the left side air temperature actuator connector.
  3. Install the instrument panel carrier onto the instrument panel.
  4. Recalibrate the right side air temperature actuator.
Mode To Remove:
  1. Remove the left floor duct from under the instrument panel (I/P).
  2. Disconnect the mode actuator connector. HVAC control module - left side gm-10-00-1844.gif

  3. Detach the mode actuator from the HVAC module.
To Install:
  1. If installing a new mode actuator, move the mode door to the middle position.
  2. Attach the mode actuator to the HVAC module. Torque the screw to 17 in-lb (1.9 Nm).
  3. Connect the mode actuator connector.
  4. Install the left floor duct under the instrument panel (I/P).
  5. Recalibrate the mode actuator.
Defrost Valve To Remove:
  1. Remove the instrument panel carrier from the instrument panel.
  2. Disconnect the defrost valve actuator connector. HVAC control module - left side gm-10-00-1844.gif

  3. Detach the defrost valve actuator from the HVAC module.
To Install:
  1. Attach the defrost valve actuator to the HVAC module. Torque the screw to 17 in-lb (1.9 Nm).
  2. Connect the defrost valve actuator connector.
  3. Install the instrument panel carrier onto the instrument panel.
Recirculation To Remove:
  1. Remove the HVAC module from the instrument panel.
  2. Detach the air inlet assembly from the HVAC module. Recirculation actuator removal and installation gm-10-00-1845.gif

  3. Disconnect the recirculation actuator connector.
  4. Detach the recirculation actuator from the HVAC module.
To Install:
  1. Attach the recirculation actuator to the HVAC module. Torque the screw to 17 in-lb (1.9 Nm).
  2. Attach the air inlet assembly to the HVAC module. Torque the screw to 17 in-lb (1.9 Nm).
  3. Connect the recirculation actuator connector.
  4. Install the HVAC module into the instrument panel.
  5. Recalibrate the recirculation actuator.
prev.gif next.gif

Aug 17, 2010 | 2004 GMC Envoy

2 Answers

I changed the battery on 2006 Trailblazer SS. Now I can only get AC from my windshield and floor vents. Nothing from the dash vents. Also the temp control only gives coldest temp. I have checked fuses...


once you disconnect the battery your body control module loses power and memory you have to get some one with a scanner with reprogramming capabilities and have the computers reset ,dealer?

Aug 05, 2010 | Chevrolet TrailBlazer Cars & Trucks

1 Answer

I have 2000 buick lesabre my ac compressor works but no cool air coming up


Mode Actuator 2000 – 2005 Mode and Left Air Temperature Actuator gm-10-00-1560.gif

To Remove:
  1. Remove the left side sound insulator panel.
  2. Remove the knee bolster.
  3. Remove the instrument panel cluster. (Automatic HVAC)
  4. Disconnect the electrical connector from the left air temperature actuator. (Automatic HVAC)
  5. Remove the left air temperature actuator. (Automatic HVAC)
  6. Disconnect the electrical connector from the mode actuator.
  7. Remove the mode actuator.
To Install:
  1. Align the mode door levers with the cam slots.
  2. Install the mode actuator and torque the fasteners to 12 in-lbs (1.4 Nm).
  3. Connect the electrical connector to the mode actuator.
  4. Install the left air temperature actuator and torque the fasteners to 12 in-lbs (1.4 Nm). (Automatic HVAC)
  5. Connect the electrical connector to the left air temperature actuator. (Automatic HVAC)
  6. Install the instrument panel cluster. (Automatic HVAC)
  7. Install the knee bolster.
  8. Install the left side sound insulator panel.
  9. Recalibrate the actuators.
Left Air Temperature Actuator 2000 – 2005 Mode and Left Air Temperature Actuator gm-10-00-1560.gif

To Remove:
  1. Remove the left side sound insulator panel.
  2. Remove the knee bolster.
  3. Remove the instrument panel cluster.
  4. Disconnect the electrical connector from the left air temperature actuator.
  5. Remove the left air temperature actuator retaining screws.
  6. Remove the left air temperature actuator.
To Install:
  1. Install the left air temperature actuator and torque the fasteners to 12 in-lbs (1.4 Nm).
  2. Connect the electrical connector to the left air temperature actuator.
  3. Install the instrument panel cluster.
  4. Install the knee bolster.
  5. Install the left side sound insulator panel.
  6. Recalibrate the actuators.
Air temperature Actuator (Manual), Right Air temperature Actuator (Automatic) 2000 – 2005 Right Air Temperature Actuator gm-10-00-1561.gif

To Remove:
  1. Remove the instrument panel compartment.
  2. Disconnect the electrical connector from the air temperature actuator.
  3. Remove the right air temperature actuator.
To Install:
  1. Install the air temperature actuator and torque the fasteners to 12 in-lbs (1.4 Nm).
  2. Connect the electrical connector to the air temperature actuator.
  3. Install the instrument panel compartment.
  4. Recalibrate the actuators.
prev.gif next.gif

Jul 04, 2010 | Cars & Trucks

1 Answer

How to install ac mode actuator on 2003 gmc sierra


prev.gif next.gif Air Door Actuators Removal & Installation Air Temperature Actuator Air Temperature Actuator Replacement gm-10-00-559.gif

To Remove:
CAUTION
Do not apply power to the actuator when it is removed from the HVAC module.
  1. Remove the instrument panel hush panel.
  2. Disconnect the connector from the air temperature actuator.
  3. Remove the air temperature actuator mounting screws.
  4. Remove the actuator from the HVAC assembly.
To Install:
  1. Position the air temperature actuator on the HVAC assembly.
  2. Install the actuator mounting screws.
  3. Install the electrical connect to the air temperature actuator.
  4. Install the instrument panel hush panel.
Right Side Air Temperature Actuator (2003-2007) Right Air Temperature Actuator Replacement gm-10-00-560.gif

To Remove:
CAUTION
Do not apply power to the actuator when it is removed from the HVAC module.
  1. Remove the instrument panel carrier.
  2. Disconnect the connector from the right air temperature actuator.
  3. Remove the actuator mounting screws.
  4. Remove the right air temperature actuator.
To Install:
  1. Position the right air temperature actuator on the HVAC assembly.
  2. Install the actuator mounting screws.
  3. Connect the electrical connector to the actuator.
  4. Install the I/P carrier.
  5. Calibrate the actuator.
Left Side Air Temperature Actuator (2003-2007) Left Air Temperature Actuator Replacement gm-10-00-561.gif

To Remove:
CAUTION
Do not apply power to the actuator when it is removed from the HVAC module.
  1. Remove the I/P insulator panel.
  2. Disconnect the connector from the left air temperature actuator.
  3. Remove the actuator mounting screws.
  4. Remove the left air temperature actuator.
To Install:
  1. Position the left air temperature actuator on the HVAC assembly.
  2. Install the actuator mounting screws.
  3. Connect the electrical connector to the actuator.
  4. Install the I/P insulator panel.
  5. Calibrate the actuator.
Mode Actuator Mode Actuator Replacement gm-10-00-562.gif

To Remove:
CAUTION
Do not apply power to the actuator when it is removed from the HVAC module.
  1. Remove the floor air outlet from the floor duct.
  2. Remove the center console and center console duct (if equipped).
  3. Disconnect the electrical connection at the mode actuator.
  4. Remove the mode actuator mounting screws from the HVAC module.
  5. Remove the mode actuator with the actuator cam attached.
To Install:
  1. Position the mode actuator with the actuator cam to the HVAC module.
    • Align the heater/defroster valve lever with the cam slot
    • Align the A/C valve lever with the cam
  2. Install the mode actuator mounting screws.
  3. Connect the mode actuator electrical connection.
  4. Install the center console duct and the center console (if equipped).
  5. Install the floor air outlet duct extension to the floor air duct.
  6. Calibrate the actuator.
Air Inlet Actuator/Recirculation Actuator Delphi Recirculation Actuator Replacement (Delphi) gm-10-00-564.gif

To Remove:
CAUTION
Do not apply power to the actuator when it is removed from the HVAC module.
  1. Remove the instrument panel upper trim panel.
  2. Remove the instrument panel lower trim panel and glove box assembly.
  3. Remove the passenger side air bag.
  4. Disconnect the connector from the recirculation actuator.
  5. Remove the recirculation actuator mounting screws.
  6. Remove the recirculation actuator from the HVAC assembly.
To Install:
  1. Position the recirculation actuator on the HVAC assembly.
  2. Install the recirculation actuator mounting screws.
  3. Connect the electrical connector to the recirculation actuator.
  4. Install the passenger side air bag.
  5. Install the instrument panel lower trim panel and the glove box assembly.
  6. Install the instrument panel upper trim panel.
  7. Calibrate the actuator.
Visteon Recirculation Actuator Replacement (Visteon) gm-10-00-566.gif

To Remove:
CAUTION
Do not apply power to the actuator when it is removed from the HVAC module.
  1. Remove the HVAC module assembly.
  2. Remove the evaporator core cover from the HVAC module.
  3. Remove the recirculation actuator from the HVAC module assembly.
To Install:
  1. Position the recirculation actuator on the HVAC assembly.
  2. Install the recirculation actuator mounting screws.
  3. Install the evaporator core cover to the HVAC module.
  4. Install the HVAC module assembly.
  5. Calibrate the actuator.
prev.gif next.gif

Jul 09, 2010 | 2000 GMC New Sierra 1500

2 Answers

Heating system only blows out hot air through the vents


I would look at the air blend doors first, it sound like they are not working or your control in the dash is not working send a signal to them. they work by changing the air from hot to cold or in between.

Avalanche, Sierra And Silverado
  1. Remove the floor air outlet duct extension (1) from the floor duct (2). 0900c152801c9c8a.jpgRemove the floor air outlet duct extension (1) from the floor duct (2)
  2. Disconnect the electrical connection at the blend door actuator (10). 0900c152801c9c8b.jpgBlend door actuator and related components
  3. Remove the blend door actuator mounting screws from the HVAC module.
  4. Remove the blend door actuator as an assembly with the actuator cam. 0900c152801c9c8c.jpgRemove the blend door actuator mounting screws from the HVAC module
To install:
  1. Install the blend door actuator as an assembly with the actuator cam.
    1. Line up the heater/defroster valve lever with the blend door actuator cam slot.
    2. Line up the A/C valve lever with the blend door actuator cam
  2. Install the blend door actuator mounting screw to the HVAC module.
    1. Tighten the blend door actuator mounting screw to 14 inch lbs. (1.6 Nm).
  3. Connect the electrical connection at the blend door actuator (10). 0900c152801c9c8b.jpgBlend door actuator and related components
  4. Install the floor air outlet duct extension (1) to the floor air duct (2).
C/K Series
  1. Disconnect the electrical connector to the mode actuator that is located on the left side of the air distribution case.
  2. Remove the screws.
  3. Remove the adjuster links from the control lever.
  4. Remove the mode actuator.
  5. Adjust the mode actuator by completing the following steps:
    1. Connect the electrical connector to the actuator.
    2. Turn the ignition switch to the RUN position. Allow the self-positioning of the actuator.
    3. Turn the ignition switch to the OFF position.
    4. Remove the actuator from the electrical connection. 0900c152801c9c8d.jpgBlend door actuator-C/K Series
To install:
  1. Install the mode actuator.
  2. Install the screws.
  3. Install the adjuster links to the control lever.
  4. Connect the electrical connector.
  5. Test the circuit operation

Nov 27, 2008 | 2001 Chevrolet Silverado

Not finding what you are looking for?
1997 Ford Explorer AWD Logo

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...