Question about 2000 Daewoo Leganza

1 Answer

Need timing specs and timing belt tensioner specs 2000 daewoo 2.2

Changed motor. New/used motor has no compression, thinking timing jumped. looking for any specs for this car.

Posted by on

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Http://servicemanual.blogspot.com/2007/09/daewoo-leganza-my2000-service-manual.html Try this link. download free manual, has timing specs and more.

Posted on Nov 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is an engine mechanical timing fault in a 2000 daewoo nubira?


mechanical timing consists of a timing belt, tensioner pulleys and timing gears
the timing may have jumped, it is something that needs immediate attention.
failure to address a timing belt issue can result in a blown engine if it breaks

Sep 20, 2011 | Daewoo Nubira Cars & Trucks

1 Answer

WHAT IS CORRECT TIMING MARKS FOR TIMING BELT INSTALLATION. 2000 NUBIRA 2.0 DOHC AND CRNKSHAFT MARKS. Thanks Joe


TIMING BELT
Removal
Disconnect negative battery cable. Disconnect intake air temperature sensor connector from intake air duct. Disconnect the air intake tube from the throttle body. Disconnect the breather tube from the valve cover. Remove resonator from throttle body. Remove air filter housing.
Raise and support the vehicle. Remove right front wheel. Remove right front splash shield from wheelwell. Remove serpentine accessory drive belt.
Remove crankshaft pulley bolts. It is NOT necessary to remove crankshaft sprocket center bolt. Remove crankshaft pulley. Lower vehicle.
Support engine assembly from above with Support Fixture (J-28467-B). Remove engine mount bracket from timing belt end of engine.Remove power steering hose clamp bolt, and position hose away from timing belt cover. Remove front timing belt cover. Using crankshaft center bolt, rotate crankshaft one full turn clockwise (as viewed from timing belt end of engine).
Align mark on crankshaft sprocket with notch at bottom of rear timing belt cover. See Fig. 4 . Align camshaft sprocket timing marks with notches on valve cover. See Fig. 5 .
CAUTION: Engine damage could result if camshaft sprockets are not properly aligned with notches on valve cover.
Loosen the automatic tensioner bolt. Use an Allen wrench to rotate tensioner and relieve tension on timing belt. Remove timing belt.
Fig. 4: Aligning Crankshaft Sprocket Timing Mark
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim_4.jpg
Fig. 5: Aligning Camshaft Sprocket Timing Marks
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim2_3.jpg
Installation
Ensure crankshaft and camshaft timing marks are still aligned. Install the timing belt. See Fig. 7 . Turn the timing belt tensioner counterclockwise to tension the timing belt. Turn tensioner until the pointer aligns with the notch on the rear timing belt cover. Tighten automatic tensioner bolt to specification. See TORQUE SPECIFICATIONS .
Using crankshaft center bolt, turn crankshaft clockwise (as viewed from timing belt end of engine) 2 full revolutions. Ensure timing belt tensioner pointer is still aligned with notch.
If timing belt tensioner is correctly aligned, install timing belt cover. See Fig. 3 . Install the engine mount bracket on the timing belt end of engine. Position power steering hose in place, and install clamp bolt. Install crankshaft pulley. Install serpentine accessory drive belt.
Install right front splash shield. Install right front wheel. Install air filter housing and resonator. Connect air intake temperature sensor connector. Connect negative battery cable.
Fig. 7: Identifying Timing Belt Routing
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim3_1.jpg
here

http://www.2carpros.com/questions/daewoo-leganza-2000-daewoo-leganza-timing-marks

Feb 17, 2011 | 2000 Daewoo Nubira

1 Answer

Timing mark diagram for a 2000 daewoo nubira cdx


here are the timming marks

7a3496b.jpg
e98992a.jpg
the other important thing is to
Rotate the automatic tensioner hex–key tab anti-clockwise until the adjust arm pointer of the timing belt automatic tensioner is aligned with the notch in the timing belt automatic tensioner bracket.
then turn engine over 2 turns and recheck marks and tensioner pointer

Nov 02, 2009 | 2000 Daewoo Nubira

1 Answer

Cambelt for Daewoo Espero 2lt Auto 98


try looking on www.gates.com hopefully you can find all the specs as well as a replacement belt for purchase, hope this helps, let me know

Jun 09, 2009 | 1999 Daewoo Lanos

3 Answers

Timing Belt Tensioner bolt broken off.


You may have a serious problem (timing belt tensioner). This tensioner keeps the belt 'taut' so it won't jump time. Daewoo engines are 'interferrence' engines (this means if the valve timing is 'off' (out of syncronization) you can damage/bend the valves in the head -- valve timing (timing belt ensures this). The solution is to take the vehicle into the shop and have it diagnosed to be sure/to know if any damage has occured -- if none, replace the tensioner... it's pretty simple to do, if you have the service manual.

May 26, 2009 | 2000 Daewoo Nubira

2 Answers

Replacing timing belt on daewoo nubira 2000 model


Instructions Difficulty: Moderate Things You’ll Need:
  • Set of ¼-inch drive sockets ¼-inch drive ratchet Set of ½-inch drive sockets ½-inch drive ratchet Set of 3/8-inch drive sockets 3/8-inch drive ratchet Set of metric wrenches Floor jack Jack stands
Step1 Raise and support the vehicle on jack stands. Remove the intake air temperature wiring, the breather hose and intake air hose. Take off the air cleaner assembly. Step2 Remove the right wheel. Remove the accessory belts. Remove the crankshaft bolt and the crankshaft pulley. Remove the power steering bolts and the timing belt covers. Temporarily install the crankshaft bolt and turn the engine clockwise until the mark on the crankshaft pulley, which is a triangle stamped into the crank sprocket, is aligned with the corresponding triangular mark on the block. Step3 Make sure that the timing marks are aligned on the camshaft sprockets. These are a line on each sprocket that runs through a tooth on each sprocket. These lines should line up in the middle between each sprocket and point toward each other. If they do not line up, turn the crankshaft one more time and they will line up. It takes two turns of the crank to one complete revolution of the cam. Step4 Loosen the water pump bolts; using the 3/8-inch ratchet, turn the water pump clockwise away from the belt and loosely tighten the bolts to keep it there. Remove the timing beltmag-glass_10x10.gif. Make sure the timing marks are aligned and install the new belt starting on the right side from the crank sprocket and working counterclockwise. Keep all the belt tension on the right side away from the tensioner. Step5 Loosen the bolts in the water pump and rotate the water pump counterclockwise to apply tension to the belt. Watch the tensioner, which is above the water pump, and apply tension with the water pump until the pointer on the tensioner lines up with the notch above it. Lightly tighten the water-pump bolts. Step6 Turn the engine two more times and align the timing marks perfectly. Loosen the water-pump bolts and, using the ratchet, apply tension to the belt until the tensioner pointers are aligned. Tighten the water-pump bolts. Step7 Install the timing-belt covers and the bolts in the power-steering pump and tighten. Remove the crankshaft bolt and install the crank pulley and the bolt, then torque the crankshaft pulley bolt to 70 foot pounds of torque. Install all components in reverse order of removal.

Mar 02, 2009 | 2000 Daewoo Nubira

1 Answer

2000 Daewoo Laganza no compression


You are more likely right to think you have done some damage to the cylinder head. If you have no compression on number 2 & 3 cylinders then I would take the head off and inspect and recondition the head. You may also have damaged the pistons or rings. Anyway with out looking for any damaged parts, you will not find what parts you will need. I would get a workshop manual for the vehicle to help you. Also if you decide to rebuild the engine, fit a new timing belt.

Dec 15, 2008 | 2000 Daewoo Leganza

1 Answer

2000 daewoo Laganza no compression


valves bent sorry for the bads news

Dec 15, 2008 | 1998 Ford Escort

2 Answers

Timeing belt


IF YOUR TIMING BELT BROKE OFF BEFORE YOU CHANGED THE TIMING BELT DO YOU HAVE TO TAKE THE COVER OFF OF THE HEAD VALVE LOOK AT THE CAMS AND YOU WILL SEE THAT THE VALVES ARE BENT IF THE CAM IS NOT TOUCHING THE VALVES ARE BENT BEFORE YOU ALINE THE CAM GEARS YOU HAVE TO PUT THE CRANK SHAFT GEAR IT HAS A MARK AT THE BOTTOM OF THE OIL PEN MAKE SURE THAT WHEN YOU GET IT ALL SET UP RETURN THE GEAR TO THE MARK ON PULLY ALSO THE TIMING MARKS ON THE CAMS HAS TO MARKS ON THE COVER THE LEFT CAM GOES AT 12:00 THE RIGHT CAM MAKE SURE THE EXHAUST LINE LINES UP AT 12:00 OTHERWISE IT WONT START BECAUSE YOU DONT HAVE NO COMPRESSION I HOPE THIS IS HELPFUL FOR ANYBODY THAT NEEDS TO REPAIR THE ENGINE



ALCANTARAMONICO@YAHOO.COM

May 16, 2008 | 2000 Daewoo Leganza

Not finding what you are looking for?
2000 Daewoo Leganza Logo

626 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

61168 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...