Question about 1991 Jeep Wrangler

1 Answer

Clutch Pedal to Floor

Just got 'the call' from my daughter; the clutch pedal just goes right to the floor-no resistance at all-stuck in gear-does'nt this sound like the clutch master cylinder is out of fluid? No fluid leak in vehicle, so she says.Vehicle is 1991 YJ

Posted by on

  • 1 more comment 
  • bleeditout09 Nov 13, 2008

    Just replaced a buddies whole clutch on his 1991 and put everything back together. Now leaks like hell from the clutch. Did we forget to do something with the slave cylinder? We put a new one in. Kit came with 4 o-rings but there are only 2 lines so my common sense said only 2 are needed. Put the new o-ring on the lines and pushed line into slave cylinder and put the "U" shaped retaining clip back in. Did I miss something? Thanks!

  • j-ormonde Mar 08, 2009

    i have a 91 jeep wrangler, and the clutch pedal falls to the floor.fluid was low so i added some but made no difference

  • Anonymous Mar 20, 2014

    Master/slave clutch assembly replaced 2 years ago. Recently all clutch pedal resistance suddenly disappears, remains stuck in gear, no disengagement, impossible to select/change gear. After a stalled stop, clutch action is restored until the next time it happens. Fluid levels fine, no leaks. When it works it is perfect, then all of a sudden, clutch to the floor.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 160 Answers

Slave cylinder needs replaced

Posted on Nov 12, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

New clutch installed. No pedal, stays on floor unless I bring it back up with my hand. No resistance.


`Did it bleed, did fluid come out in a steady stream? Isn't there a spring to bring the pedal off the floor?
Check the linkage of the pedal to rod to the clutch master cylinder, make sure that is all together. Any chance the master has an internal leak and won't build hydraulic pressure down at the slave? If you get it bled, then watch the slave operation while someone works the clutch pedal. The piston on the slave should extend and push the clutch fork enough to disengage the clutch.

Jul 19, 2015 | Nissan Cars & Trucks

1 Answer

How do you adjust the clutch on a 2000 golf se tdi 1.9


Renew the clutch cable its a auto adjust mechanism and the cable comes with a plastic tie around the middle bit so fit the cable and then and only then remove the tie ,this is a difficult job and not easy for a weekend mechanic so be warned

Mar 01, 2014 | Cars & Trucks

1 Answer

1988 chevy k2500 clutch pedal has no resistance


Your truck has a hydraulic clutch release system, you have a problem in it due to a leak in the slave or the master cylinder, The slave cylinder which is the one that leaks most often is inside the bell housing and it requires the ****** be removed to replace it.

Aug 09, 2012 | Cars & Trucks

1 Answer

Clutch will not engage when it was engaging perfectly to begin with.


Your car has a hydraulic clutch release system, it is defective, either the master or slave cylinder is leaking or pulling in air and this causes the clutch pedal to go to the floor.

Aug 06, 2012 | Cars & Trucks

1 Answer

1989 Jeep Cherokee - replaced clutch master cylinder, clutch looses resistance sometimes. Goes all the way to floor.


they hav a nuetral safety switch or depressn the pedal is common--send issue to magicmechanic in orlando-hes a mastertech with any car or system--chec out the sites Q n A first

May 20, 2012 | Cars & Trucks

1 Answer

Why wont my car switch gears when turned on?


I assume this is a manual transmission, so in that case you have a clutch problem, how does the clutch pedal feel, soft allot of free play? Goes to the floor with no resistance?

Nov 30, 2011 | 2003 Volkswagen Passat

2 Answers

1999 1.4 Ford Fiesta: When depressing clutch a very noisy rumbling sound but gear changing as normal. I added some gearbox oil and the noise stopped. Then, just the following day, no resistance when...


Hi There.
sounds like your release bearing has either collapsed or seized, either way you will have to drop the gear box and check it out... should'nt be a problem on a 1999 fiesta. just be careful not to pop a drive shaft and lose the transmission fluic on the floor.
Good Luck

May 03, 2011 | 2007 Ford F

2 Answers

Lost resistance on clutch pedal and hard to change gears also when topping up clutch fluid it does`nt last that much and leaks from slave cyclinder


If the slave cylinder is leaking, replace the slave cylinder. You are loosing hydraulic pressure in the clutch and is the reason why it is not engaging correctly.

Apr 13, 2011 | 2001 Honda Accord

Not finding what you are looking for?
1991 Jeep Wrangler Logo

892 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

74115 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22082 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7188 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...