Question about 1995 Toyota Pickup

1 Answer

I need to know how to install the A/C pump on a 95 toyota pickup

I removed the pump to do an engine swap and now i can't remember how it goes back on. Can you help me?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Toyota Master
  • 959 Answers

There is a belt diagram right on the raditer support.(or should be somewhere) The coolant lines should help you find its possition too.

Posted on Jan 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can I use a 95 4 runner engine in my 83 Toyota pickup.


Not likely. The 1995 engine will most likely be designed for computerized control with all the newer sensors. These did not exist in 1983. Not to mention trying to get an adapter to mate the transmission and remainder of drive train. The days of cross-year engine swapping have been made very difficult because of PCM program controls, but that same technology makes the engines themselves run better and last longer.

Oct 22, 2015 | Toyota Cars & Trucks

2 Answers

1987 toyota pickup 22r engine


http://www.toyotanation.com/forum/showthread.php?t=234221

this may be of some help to you.

also the diagram you requested.


2d59067.jpg

May 18, 2008 | 1987 Toyota Pickup

1 Answer

How to replace starter on 95 nissan pickup truck


remove negative on battery terminal, there are two bolts that hold it in between transmission and engine (17mm), loosen it. pull it out and remove all wirings by unscrewing (10mm) just remember which goes which. then reverse procedure :)

Dec 09, 2010 | 1995 Nissan Pickup

1 Answer

How do i change the oil pump in a 2000 dodge intrepid


I'm assuming that you are talking about 2.7L, the check this procedure...

Removal & Installation - 2.7L Engines
  1. Drain the engine oil.
  2. Remove or disconnect the following:
    Crankshaft damper Timing chain cover Timing chain Crankshaft sprocket Oil pan Oil pickup tube and O-RING Oil pump

To install:


f24d78a.jpg

Fig. Oil pump mounting bolt locations-2.7L engine

  1. Fill the oil pump rotor cavity with clean engine oil.
  2. Carefully, install the oil pump over the crankshaft and into position.
  3. Install the oil pump mounting bolts and torque to 21 ft. lbs. (28 Nm).
  4. Lubricate the new pickup tube O-ring with clean engine oil and torque the pickup tube mounting bolts to 21 ft. lbs. (28 Nm).
  5. Install or connect the following:
    Oil pan Crankshaft sprocket Timing chain Timing chain cover Crankshaft damper
  6. Fill the engine with clean engine oil.
  7. Start the vehicle, check for leaks and repair if necessary.

Hope helps (remember to rate this).

Oct 02, 2010 | 1999 Dodge Intrepid

1 Answer

I have a 89 toyota extra cab pickup with v6. it needs tranny. what years will interchange? going to swap for working tranny from private owner. where to start.


i thinks it will swap with a 89 to 95, possible a 96 will work. the identification label on the inside of the door will have your tranny listed. g58, w56, w59 and r150f. something like that, find another like it and your good to go.

Sep 08, 2010 | 1989 Toyota Pickup SR5

1 Answer

94 Toyota Pickup. I have a new engine to install,


Try turning the engine over on the ignition switch with the fuel pump fuse removed and the spark plugs removed and coil disconnected. The engine will turn easily on the starter motor and will cause the oil pump to push oil around all the passages. A couple of minutes should be enough. When ready to start reconnect the coil, refit the plugs and insert the pump fuse.

May 07, 2010 | 1994 Toyota Pickup

1 Answer

Are the parts from a 1990 toyota 4 runner interchangeable with a 1991 4 runner? I'm not looking to swap the engine, just the exhaust system, power window motors and such.


most parts from 90-95 will interchange. also, alot of parts from the pickups during those years are interchangeable with the 4runner.

Feb 05, 2010 | 1991 Toyota 4Runner

1 Answer

Engine swap


yes, the web site called northwestoffroad.com order the $5.00 mag. has all u need. also check website LG engineering.com. but what ever u do don't install a 3.0l v6 toyota truck engine has no power. good luck

Jun 20, 2009 | 1992 Toyota Pickup

1 Answer

Windshield washer pump


Its really easy it should be off the driver side of your engine bay. you'll need to remove the washer bottle and take off the hoses (make sure you remember where they go) and swap out the washer motor and reinstall in reverse order

Apr 27, 2009 | 1997 Nissan Pickup

5 Answers

Need to change engines


If you have a 22r carbed then all 22r carbed engines from 1981-1995 will interchange. You may need to use sensor out of your old engine however. The 20r,22r,22re,22ret all have the same mounts and tranny bolt patterns. how ever there are lot of differences. you can swap from a 22r to a 22re but you must also swap the entire vehical wiring harness to do it right. if you have a 3.0L i would keep the same engine. some people have swap to the tacoma 3.6L but that is a expensive swap not exsactly bolt on so to say. If you have a 22re then stay with the 1986-1987 22re because the newer 22re use different computers, electronics ,sensors and more.. Same story with the 22ret. I hoped this helped.

Mar 26, 2009 | 1987 Toyota Pickup

Not finding what you are looking for?
1995 Toyota Pickup Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...