Question about 1997 Dodge Intrepid

1 Answer

1997 Intrepid sport check engine codes

Can anybody tell me what these codes mean 1,2,3,3,2,4,2,3,5,5 for my check engine codes

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Chrysler codes are counted by flashes followed by a pause between codes..what you have is a code 12-start codes, code 33-AC relay circuit ope or shorted, code 24-throttle position sensor voltage too high or too low, code23-a problen with your air tempature sensor, code 55-end of codes. Next time call any parts dealer, napa,autozone, etc. they will be glad to help you..

Posted on Nov 12, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does code P0171/P0174 mean


Banks 1 and 2 are lean. Could be mass air sensor. Fuel filter dirty injectors . Vacume leak. Or computer needs updated

May 27, 2014 | 2005 Mercury Mariner

1 Answer

I have 2003 volvo s40, its check engine is on and i used OBD and gave me this code: P0015, anybody knows what it means and how to figure it out?


P0015-camshaft position actuator B-Bank 1 timing over - ******.

1.9 ltr right? Engine prone to sludge. Try and engine flush like seafoam (don't drive with it in your engine.... run it for a few minutes then shut it down) then change your oil and filter to a good quality synthetic. Then clear the code. Won't hurt it if you drive it with this code but can be annoying.

Jan 10, 2012 | 2003 Volvo S40

2 Answers

What is the red light on dash that says check engine for


its hard at find take it to an authorized garage they will find the problem by attaching the company computer software

Feb 04, 2011 | 1988 Dodge Aries

2 Answers

Hey i have a hummer h2 2004 and i have the check engine ligh on the code is p0135 (bank 1, sensor1) what sensor is it? thanks


Hello: Bank 1 tells you it is the side of the engine that has #1 cylinder (Which on your truck is the drivers side) SENSOR 1 IS THE SENSOR FOR THAT BANK IN FRONT OF THE CATALYTIC CONVERTER. This code tells us the heater in the sensor has a problem. You should replace the sensor. (Experience: I highly recommend a GM part. The GM engine control module is very sensitive to 02 sensors). Make sure the truck end of the harness connector is clean and not damaged. After replacing sensor you will have to have the code cleared. (auto Zone, Advance Auto may can do it and not charge you.

Jan 08, 2011 | 2003 Hummer H2

1 Answer

NEED TO REMOVE STARTER AND DON'T KNOW HOW


I found your solution (with pics) at:
http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0900c1528006a865

However, www.autozone.com will expect you to register (free) to access their repair guide database.
Note: The Intrepid 3.5L engine takes the Delco starter, while the Intrepid 3.3L engine takes the
Nippondenso starter.
How can you tell which engine's in your Intrepid? read 8th digit of the VIN code.
VIN code "F" - 3.5L 6cyl MFI (multi-port fuel injection) - 60% of 1997 Dodge Intrepids sold
VIN code "T" - 3.3L 6cyl MFI - 40% of 1997 Dodge Intrepids sold

Oct 25, 2010 | 1997 Dodge Intrepid

1 Answer

My jaguar started flashing the message "failsafe engine mode"


Go to your local garage (anyone) and have them read the OBDII code this will tell you what has caused the problem, cost for this should be minimal £7-10 ask them for all the reported codes you can check them out at http://www.bluejag.co.uk if you wish to find out what they mean.

Apr 04, 2010 | 2002 Jaguar S-Type

1 Answer

1997 dodge intrepid 3.5


Transmission control solinoid. Trouble code should give you the awnser.

Mar 15, 2010 | 1997 Dodge Intrepid

1 Answer

Transmission issues


Try to get a diagnostic done first ,usually it is an electrical problem.

Mar 07, 2010 | 1997 Dodge Intrepid

2 Answers

I took my 97 intrepid to emission bu it din't pass because the check engine light was on, they only give a code p1698 but i don't know what it means


It means that the shop did not have the teating computer hooked up correctly. Go to autozone and have them give you a read out of the OBDll.

Jan 21, 2010 | 1997 Dodge Intrepid

Not finding what you are looking for?
1997 Dodge Intrepid Logo

Related Topics:

372 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

71231 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7001 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...