Question about 1998 Dodge Durango

1 Answer

1999 dodge durango

Have a 1999 dodge durango there is brake fluid coming from the inside of the wheel hub do you have any solutions on what this could be? broken line, wheel cylinder?

Posted by on

  • mlhwrh1 Nov 11, 2008

    is this job expensive

  • Anonymous Mar 12, 2014

    Clicking when turning

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 147 Answers

Wheel cylinder would be your problem

Posted on Nov 11, 2008

  • Joshua Davis Nov 12, 2008

    not really do it your self 4 under 40$

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

Brake pedal almost going to the floor and fluid coming from the rear on a 2000 Durango


Sounds like you have a leak in the drum brake wheel cylinder. They happen, and more often than you would expect.

You'll see in the pictures, one is the new part and the other shows where it is on your truck.

If the cylinder went bad, you'll see brake fluid leaking, even slightly, out of the rubber boot on either side of the cylinder.
/uploads/images/brake-pedal-almost-going-floor-fluid-35055852-3-1.jpg
/uploads/images/brake-pedal-almost-going-floor-fluid-35055852-3-2.jpg

Feb 23, 2015 | 2000 Dodge Durango

1 Answer

Fluid looks like transmission fluid leaking from front passenger side in front of the tire


Check your brake lines sounds like a brake issue is it a 4x4 check your axle seals also.

Feb 15, 2013 | 2004 Dodge Durango

1 Answer

The brake system on a 2002 dodge durango has no pressure


Do you actually see brake fluid coming from the bleeders? Check for a broken brake line. If no fluid is being lost and the peddle has proper pressure, then the brake booster has failed. If their is no pressure at all, then the master cylinder has failed. Replace accordingly.

Dec 05, 2011 | 2002 Dodge Durango

1 Answer

Best way of replacing a caliper on 1999 dodge durango


jack the truck up , secure it so it can not fall down or roll away etc.
remove the wheel.
remove used caliper,
secure the used caliper to the strut spring with a wire or coat hanger..

hang the new caliper on the rotor.
remove the brake hose to the used caliper and apply to the new caliper.

Make sure brake fluid is full and cap is off of the master cyl. reservior.
open the bleader valve on the new caliper and let it gravity feed the fluid until full/overflowing.
place the brake pads on the new caliper and replace the caliper securely on the truck and replace the wheel.

bleed the brakes of any air.

Nov 28, 2011 | 1999 Dodge Durango

2 Answers

My brake line broke under the drivers sear of my 99 durango does the who break line need to be replaced. All the fluid leaked out and you can hear air coming out in the front wheel


Pressure fittings can be used depending on how bad the line actually is you can cut it back far enough to where it is good and use another length of brake line with a few pressure fittings if you do not want to go all new lines however you'll still need to bleed the system brake line to that wheel as well as possibly the passenger side. Obviously you'll need Brake fluid and a few tools.

Nov 07, 2009 | 1999 Dodge Durango

2 Answers

Broken Brake line


It's the same as any other car or truck. Simply cut the rubber off & there's a nut,like any other brake line. Loosen the lines as you would for any job. Now you say the lines are rusted,if they're that bad then you'll need to replace them from front to rear. This requires a tubing bender(hand held) & a doulble flare tool & unions. You can forget about that "expensive" part. It's a brake balance controler & never goes bad.

Jun 23, 2009 | 1999 Dodge Durango

2 Answers

Cant remove wheel hub


here is procedure

Section 04-01: Suspension and Wheel Hubs, Front 1996 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Wheel Hub Bolt Removal
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly. Refer to Section 04-04 .
  1. Remove disc brake caliper (2B120), and front disc brake rotor (1125). Refer to Section 06-03 .
Brake Shoe and Lining Removal
  1. Remove brake master cylinder filler cap (2162). Check fluid level in brake master cylinder reservoir (2K478). Remove brake fluid until brake master cylinder reservoir is half full. Discard removed fluid.
  1. Raise vehicle on hoist. Refer to Section 00-02 .
  1. Remove wheel and tire assembly from front disc brake rotor mounting face. Use care to avoid damage or interference with disc brake caliper (2B120), front disc brake rotor shield (2K004) or front wheel knuckle (3K185).
  1. Remove rear brake pin retainers (2N386). ( I think it is a T 40 torx bit you need)
  1. NOTE: It is not necessary to disconnect hydraulic connections.

    Lift disc brake caliper from front disc brake caliper anchor plate (2B292) and front disc brake rotor (1125). Do not pry directly against metal caliper piston or damage will occur.
  1. Position disc brake caliper out of the way and support with wire to avoid damaging the disc brake caliper and front brake hose (2078).
  1. Remove outer brake shoe and lining (2001) assembly from front disc brake caliper anchor plate.
  1. Remove inner brake shoe and lining assembly.
  1. Position lug bolt (1107) to clear front wheel knuckle (3K185).
  1. Remove lug bolt from wheel hub (1104).



7548d8f.gif

Installation
  1. Install lug bolt into wheel hub.
  1. Using a lug nut (1012), seat wheel hub bolt into wheel hub.
  1. Install front disc brake rotor and disc brake caliper. Refer to Section 06-03 .
  1. Install wheel and tire assembly. Tighten lug nut to 115-142Nm (85-104 lb-ft).

May 25, 2009 | 1996 Mercury Sable

1 Answer

After 20 miles rear brakes tighten up and makes thumping noise


It is probably the flexible rubber brake line that runs from the axle to the metal brake line on the frame. When these become old they don't allow the brake fluid pressure to reduce when the brake is released.

May 04, 2009 | 1999 Dodge Durango

2 Answers

The ABS and brake warning lights flash on and off, why?


could possibly be the rear wheel/brake cylander dodge had a problem with them blowing out and leaking all the fluid out

Aug 02, 2008 | 1999 Dodge Durango

Not finding what you are looking for?
1998 Dodge Durango Logo

Related Topics:

156 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

70365 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...