Question about 1995 Mercury Grand Marquis

1 Answer

95 grand marquis oil pressure guage wont work

Oil pressure guage stopped working,on a long trip it worked for a while until i turned off the car,then would'nt work again,replaced the little part that threads into the oil filter housing,still would'nt work.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 393 Answers

Have someone put an actual guage on it to make sure there is enough press. to show on dash.

Posted on Nov 12, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oil pressure sensors location on 95 grand marpice


Look here, just in front of the oil filter. There will be a wire harness attached.

25697999-kz2shk4ja2knmotuu3dm4rcj-1-0.gif

May 16, 2015 | 1995 Mercury Grand Marquis

2 Answers

How to reset the change oil light on a 1997 rav4


rav4 reset maintenance light
pretty standard
hold trip A in with engine and key off while holding trip button in turn key and engine on.
keep holding trip button in until light stops flashing when it stops flashing then release the trip reset button this should clear the maintenance warning light. hope this helps

Dec 26, 2014 | 1997 Toyota RAV4

1 Answer

Why does oil pressure light comes back on after 30 sec


Never, ever disconnect an oil sensor. It does not lie. You have no oil pressure because your oil pump is not working or no oil in the engine.

Dec 12, 2014 | Cars & Trucks

1 Answer

Oil pressure low stop engine and check guage


Fist check oil level, the sensor is a pressure switch worked by oil pressure, hopefully the sensor has gone faulty. The oil pressure needs checking, if the oil pump or relief valve has gone faulty, the engine is being starved of lubrication and is causing internal damage. It is advisable NOT to run the engine till the pressure has been checked. (hope it's the sensor)

Jan 07, 2014 | 2002 Chevrolet TrailBlazer

1 Answer

NO OIL PRESSURE READING ON DASH


remove sending unit and install mechanical gauge to see oil pressure psi if psi reads ok- change sending unit again if psi to low less then 6 replace oil pump och.

Sep 18, 2012 | 1990 Toyota 4Runner

1 Answer

Gas guage not working on 1987 grand marquis


No the fuel gauge is mechanical, it could be an issue with the sender unit or the wiring between the sender unit and the gauge

Mar 05, 2012 | 1987 Mercury Grand Marquis

1 Answer

HONDA CIVIC LX 1993 AFTER EXPOSED TO SUNLIGHT FOR LONG TIME,...ENGINE WILL JUST STOP AFTER SHORT DISTANCE AND HARD TO START...AFTER A WHILE,IT WILL START AGAIN...


sun has nothing to do with it but heat may cooling system may not be working 100% hot days may over heat the oil and oil pressure drops,oil pump may be worn you need an accurate temp guage & oil pressure guage and monitor them next time it happens some engines have oil pressure watch dog that kills engine if oil pressure drops

Aug 11, 2011 | Honda Civic Cars & Trucks

1 Answer

I just bought a 1988 chevy k/1500 4-wd truck. the temp guae volt meter oil pressure guage in the cluster all worked the rest did not. I found a replacement at a local scrap yard. now the temp volt and oil...


first we will start will the fuel gauge most likely you are correct chevys and 1995 and older jeep wranglers had this problem the sending units failed very commonly. you could have possibly gotton another bad cluster but most likely the speed sensor has worn out. it has a plastic gear being turned by a metal gear and is located near the tail of the transmission. hope this helps

Jan 30, 2011 | 1988 Chevrolet K1500

1 Answer

My 1995 mercury grand marquis will not start what troubleshooting steps should i take to get it running? The starter works but it wont turn over as if there is no fuel getting to the pistons how would i...


the fuel shutoff is on the right side of the trunk for a 95 marguis ls. my soundsystem tripped mine just press the red button to reset and hopefully that should help you

Dec 12, 2010 | 1995 Mercury Grand Marquis

1 Answer

The oil pressure guage on my 2000 Jeep Grand Cherokee is registering 0. My oil was just changed and I don't see any indication of oil leaking anywhere. Could it be the sensor?


First off I wouldnt drive your car until you make sure that you have indeed oil pressure and that the gauge is a false reading, driving your car if in fact it has no oil pressure will severly damage your engine, but firstly i would check the oil pressure switch its located on the passenger side of the engine right back from the oil filter make sure the connector is clean and free from oil and corrosion if the connector appears to be in good shape take a paper clip and insert it between the 2 terminals inside the connector your oil pressure gauge should peak at 80 PSI that tells you that your gauge and all related wiring are good and in working condition, secondly remove the oil pressure switch and hook an manual oil pressure gauge up to you engine and start the engine the guage should have a oil pressure reading anywhere from 30 PSI to 55PSI depending on engine temperature if theres oil pressure on your manual gauge replace the oil pressure switch with a new unit, if you still have 0 PSI on your gauge then stop your engine immediatly and start looking at your oil pump and lubricating system for a problem.

Dec 06, 2010 | 2001 Jeep Grand Cherokee

Not finding what you are looking for?
1995 Mercury Grand Marquis Logo

Related Topics:

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

78289 Answers

fordexpert

Level 3 Expert

5655 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...