Question about 1997 Toyota RAV4

1 Answer

Water pump How do I install a water pump on toyota rav 4

Posted by on

  • Anonymous Mar 17, 2014

    replace water pump on 98 rav 4 diagram

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 1 Answer

It took approximately 45 minutes to remove the alternator, the belt and the water pump. it then took another 45 minutes to put everything back in place. it was extremly easy!

Posted on Nov 12, 2008

2 Suggested Answers

duane_wong
  • 6826 Answers

SOURCE: where is the water pump

Water Pump REMOVAL & INSTALLATION 5VZ-FE Engines Fig. 1: The water pump is located on the front of the engine block, behind the timing cover 93163p92.jpg
Fig. 2: Once the retainers are removed, pull the pump away from the block 93163p97.jpg
Fig. 3: Scrape any remaining gasket material from the block before installing the new pump 93163p98.jpg
Fig. 4: Water pump mounting bolt locations 93163p88.jpg
Fig. 5: Front view of the water pump and thermostat housing 93163p99.jpg
WARNING
This procedure requires the removal of the timing belt. This is an extensive procedure requiring precision work, particularly at assembly. For more information, refer to Timing Belt Removal and Installation. Do not attempt to remove the belt without consulting the procedure; extreme engine damage may occur. Fig. 6: Apply sealant to the areas shown 86823pi7.gif
Fig. 7: A and B bolt locations 86823pi8.gif
Fig. 8: Exploded view of the water pump arrangement — 5VZ-FE engine 93163g19.gif

  1. Drain the cooling system.
  2. Remove the timing belt. For additional information, please refer to the following topic(s): Timing Belt Removal and Installation.
  3. Remove the idler pulley.
  4. Remove the thermostat.
  5. Disconnect the oil cooler hose from the pump.
  6. Remove the seven bolts and the tension spring bracket and then remove the water pump. To install:
  7. Clean all parts well. It is good practice to carefully clean all threaded openings, especially those exposed to coolant to remove rust and scale so at assembly, an accurate torque reading is obtained. This is important since gasketless applications like this depend on even clamp loads from the fasteners to avoid distortion and leaks. Remove any old sealer (Toyota calls it packing) from the pump and mounting area of the engine. Keep oil off the mating areas.
  8. Apply Formed In Place Gasket (FIPG) sealer to the pump-to-block mating surface and then tighten the bolts marked A in the illustration to 13 ft. lbs. (18 Nm). Tighten those marked B to 14 ft. lbs. (20 Nm). NOTE: The parts must be installed within 5 minutes of application of the sealant. Otherwise you must remove and reapply the sealer.
  9. Connect the oil cooler hose.
  10. Install the thermostat with a new gasket.
  11. Install the idler pulley.
  12. Install the timing belt.
  13. Install the drive belts and adjust the tension.
  14. Refill the cooling system and check for leaks.
2RZ-FE and 3RZ-FE Engines
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. If equipped with an air conditioning compressor or power steering pump drive belts, it may be necessary to loosen the adjusting bolt, remove the drive belt(s) and move the component(s) out of the way.
  4. Remove the fluid coupling with the fan and water pump pulley.
  5. Remove the water pump. To install:
  6. Clean the gasket mounting surfaces.
  7. Install the replacement water pump using a new gasket.
  8. Install the water pump pulley and fluid coupling with the fan.
  9. Install the removed engine drive belts.
  10. Fill the cooling system.
  11. Connect the negative battery cable. Start the engine and check for leaks.
  12. Bleed the cooling system.
1FZ-FE Engine Fig. 9: Exploded view of the water pump mounting on the 1FZ-FE engine 86823pk0.gif
Fig. 10: Detach the oil cooler hose from the clamp on the fan shroud 86823pk3.gif
prev.gif next.gif

Posted on Jul 13, 2010

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Is it very difficult to change the cam iol seal on a 2.0 toyota rav 4 1999, and is there anything I should know that the book doesn't tell


pulling the timing belt on older RAV4 engines is a more difficult task but not impossible.

Do you have some experience with timing belts and or cars in general?

Apr 05, 2013 | 1999 Toyota RAV4

1 Answer

1998 toyota rav 4 that keeps overheating. I just replaced the thermostat


Thermostat may be installed upside down...this can cause overheat.
To test your engine...if you don't think thermostat is faulty, remove the thermostat.
This is sometimes called "running cold"...and it should not overheat. If it does, you have bigger problem than thermostat.
You can test thermostat too by placing it in hot water thats not quite boiling and see if its opening properly.

Hope this helps...

Aug 28, 2011 | 1998 Toyota RAV4

1 Answer

How do I remove the dash on my 1997 Rav 4 so I can get at the radio


This Toyota Rav-4 1998 to 2000 - Radio Installation / Stereo Installation coudl helped: InstallDocs/Toyota/PDF/869029.pdf

Good luck.

Jun 03, 2011 | 2003 Toyota Camry

1 Answer

How often should timing belt be replaced on toyota 97 rav 4


every 60 thousand is best as the longer you go the more chance of it breaking and causing damage. some last as much as 120 thousand but remember that time dry rots the rubber and that is why they break or strip out it is also recommended you change your water pump with this service because they have about the same life expectancy and belt drives the pump.

Nov 21, 2010 | Toyota RAV4 Cars & Trucks

1 Answer

Is the water pump on a 2007 rav 4 internal or external


Its internal.

Here's a How To: http://www.ehow.com/how_4914451_replace-water-pump-rav.html

Jul 27, 2010 | 2007 Toyota RAV4

1 Answer

Where is the water pump


Water Pump REMOVAL & INSTALLATION 5VZ-FE Engines Fig. 1: The water pump is located on the front of the engine block, behind the timing cover 93163p92.jpg
Fig. 2: Once the retainers are removed, pull the pump away from the block 93163p97.jpg
Fig. 3: Scrape any remaining gasket material from the block before installing the new pump 93163p98.jpg
Fig. 4: Water pump mounting bolt locations 93163p88.jpg
Fig. 5: Front view of the water pump and thermostat housing 93163p99.jpg
WARNING
This procedure requires the removal of the timing belt. This is an extensive procedure requiring precision work, particularly at assembly. For more information, refer to Timing Belt Removal and Installation. Do not attempt to remove the belt without consulting the procedure; extreme engine damage may occur. Fig. 6: Apply sealant to the areas shown 86823pi7.gif
Fig. 7: A and B bolt locations 86823pi8.gif
Fig. 8: Exploded view of the water pump arrangement — 5VZ-FE engine 93163g19.gif
  1. Drain the cooling system.
  2. Remove the timing belt. For additional information, please refer to the following topic(s): Timing Belt Removal and Installation.
  3. Remove the idler pulley.
  4. Remove the thermostat.
  5. Disconnect the oil cooler hose from the pump.
  6. Remove the seven bolts and the tension spring bracket and then remove the water pump. To install:
  7. Clean all parts well. It is good practice to carefully clean all threaded openings, especially those exposed to coolant to remove rust and scale so at assembly, an accurate torque reading is obtained. This is important since gasketless applications like this depend on even clamp loads from the fasteners to avoid distortion and leaks. Remove any old sealer (Toyota calls it packing) from the pump and mounting area of the engine. Keep oil off the mating areas.
  8. Apply Formed In Place Gasket (FIPG) sealer to the pump-to-block mating surface and then tighten the bolts marked A in the illustration to 13 ft. lbs. (18 Nm). Tighten those marked B to 14 ft. lbs. (20 Nm). NOTE: The parts must be installed within 5 minutes of application of the sealant. Otherwise you must remove and reapply the sealer.
  9. Connect the oil cooler hose.
  10. Install the thermostat with a new gasket.
  11. Install the idler pulley.
  12. Install the timing belt.
  13. Install the drive belts and adjust the tension.
  14. Refill the cooling system and check for leaks.
2RZ-FE and 3RZ-FE Engines
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. If equipped with an air conditioning compressor or power steering pump drive belts, it may be necessary to loosen the adjusting bolt, remove the drive belt(s) and move the component(s) out of the way.
  4. Remove the fluid coupling with the fan and water pump pulley.
  5. Remove the water pump. To install:
  6. Clean the gasket mounting surfaces.
  7. Install the replacement water pump using a new gasket.
  8. Install the water pump pulley and fluid coupling with the fan.
  9. Install the removed engine drive belts.
  10. Fill the cooling system.
  11. Connect the negative battery cable. Start the engine and check for leaks.
  12. Bleed the cooling system.
1FZ-FE Engine Fig. 9: Exploded view of the water pump mounting on the 1FZ-FE engine 86823pk0.gif
Fig. 10: Detach the oil cooler hose from the clamp on the fan shroud 86823pk3.gif
prev.gif next.gif

Jul 13, 2010 | 1997 Toyota RAV4

1 Answer

1999 toyota rav 4 engine oil cooler bolt torque setting


INSTALL OIL COOLER
-clean the oil cooler contact surface on the oil cooled mounting
-install a new O-ring to the oil cooler.
-temporarily install the oil cooler with the nut
-apply a light coat of engine oi on the threads and under the head of the relief vale
-install the plate washer and union bolt. torque 78Nm (800kgfcm, 58 ft lbs.)
-tighten the nut,torque 8.8Nm (90kgfcm, 78 inch lbs.)
-connect the 2 water bypass hoses to the oil cooler.

HOPE THIS CAN HELP.

Apr 26, 2010 | 1999 Toyota RAV4

1 Answer

No water flow through heater core no heat toyota rav 4 ...flushes heater core nothing


might need new heater core ....thermostat stays open ...it is definitely plugged then ..so change it ....the heater core ....

Jan 03, 2010 | 1996 Toyota RAV4

2 Answers

97 toyota rav 4 dies at accel.


most likely its your fuel pump. when the rpm's start to drop just give the gas pedal a few pumps and you should be good.

Nov 17, 2008 | 1997 Toyota RAV4

Not finding what you are looking for?
1997 Toyota RAV4 Logo

Related Topics:

492 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

63291 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...