Question about 1994 Toyota Camry

1 Answer

Headlight adjustment The whole headlight is not seated properly as well as the beams not being adjusted correctly. So, how do I take out the headlight and "re-seat". Tried the adjusting screw for the beams, but this did nothing. Any help would be appreciated. thank you.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had this problem. The plastic grommet that the headlight fit into was cracked. I got a headlight assembly from CertiFit (cheaper than dealer.) Or try a junkyard.

Posted on Nov 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Low beam headlight adjustment on 2011 Chrysler 200


How to Adjust Car Headlights Level your car. Start by removing any excess weight from the trunk of the car. Also, ensure that the tire pressure in all tires is at the manufacturer's recommended levels. If possible, have somebody sit in the driver's seat, and that the gas tank is half-full. As well as this, check that your headlight aim adjustment wheel (if fitted) is at the zero position. Position your car. On level ground, park 10 to 15 feet (3.0 to 4.6 m) from a dark wall or garage door, with the front of the car aimed at the wall. A paved parking lot or level driveway is best Turn the headlights on. Do not use your high beams or fog lights. Mark the horizontal and vertical center lines of the headlight beams with masking tape to make two T's on the wall or garage door.Make sure the lights are level. Place a carpenter's level between the two marked center lines to see if they are even. If they are not even, use a tape measure to measure how far up the wall the lower mark is and lower the other center line marker to the same height. These center lines should be no higher than 3.5 feet (1.1 m) from the ground.Back your car exactly 25 feet (7.6 m) from the wall or garage door. Don't estimate the distance! Use a tape measure to make sure you are the proper distance away from the wall. Turn off the headlights. Remove the trim ring from around the headlights and locate the adjusting screws. These screws are typically found adjacent to the headlight, though some manufacturers put the screws in the engine compartment, behind the the headlights. The horizontal adjuster and the vertical adjuster should be marked.
  • Always defer to the specs in the owner's manual-Adjust each headlight separately. Block one with a sweatshirt or other object while adjusting and testing the other, since the light-bleed can make it difficult to distinguish one from the other. Have a helper sit in the driver's seat while you do the adjustments, to turn the lights on and off while you make the proper adjustments

Sep 30, 2016 | 2011 Chrysler 200

1 Answer

Headlight adjustment


AIMING

The procedure outlined here is intended to provide a basic adjustment only.
  1. Park the vehicle on a level surface 25 feet (7.62 meters) from a vertical wall. There must be a horizontal reference point, such as a line on the pavement or another wall, at a right angle to the aiming wall. The fuel tank should be about 1/2 full, tire pressures must be correct and there must be a person in the driver's seat.
  2. Measure the distance from the floor to the center of each headlight. Mark these heights on the wall and draw a line between them.
  3. Measure the horizontal distance from the reference point to the center of each headlight. Make reference marks on the wall so that X marks the center of each headlight.
  4. With the headlights on low beam, the high intensity zone of the light beam should be immediately below the line and about 2 inches to the right of the center of each headlight.
  5. If adjustment is required, remove the grille and use a Phillips screwdriver to turn the adjuster screws.

Sep 28, 2015 | 1987 Volkswagen Jetta

2 Answers

My lights are not see properly if i dip my lights i can only see in a distance of 5mitres but if i beam mylights i can see a distance of 9 to 10 mitres its a toyota corolla ae91 please help me


Your headlights need aiming correctly. There are screws next to the headlight the achieve this . Park the car on level ground about 2 meters (6feet) from a solid wall and turn the lights on to high beam. You will see the centre of the beam measure the height from the floor to the center of the headlight and mark this on the wall directly in front of the vehicle. The center of the beam has to be adjusted to to this point.Don't worry about low as the beam for low is set by the bulb and is correctly positioned in relation to high at all times

Feb 07, 2013 | 1990 Toyota Corolla

1 Answer

Just bought a used 05 subaru impreza. Noticed the right head lamp is pointed too high. where is the adjustment screws to lower the lamp. It seems great on the horizontal just needs to be adjusted on the...


I hope this info helps!

ADJUSTMENT

HEADLIGHT AIMING

CAUTION: Turn off the light before adjusting headlight aiming. If the light is necessary to check aiming, do not turn on for more than 2 minutes.


  1. Before checking the headlight aiming, be sure of the following:
    • The area around the headlight has not sustained any accident, damage or other type of deformation.
    • Vehicle is parked on level ground.
    • The inflation pressure of tires is correct.
    • Vehicles gas tank is fully charged.
    • Bounce the vehicle several times to normalize the suspension.
    • Make certain that someone is seated in the driver s seat. Turn the headlights on and then adjust the low beam pattern to the following positions on the screen.
  1. Position the headlight beam leveler switch to "0" .
129148368


129148369


129148370



  1. Rotate the adjusting screw (A) to adjust aim.

Aug 01, 2011 | Subaru Impreza Cars & Trucks

1 Answer

How do i adjust the head lights on a 1997 grand marquis


AIMING THE HEADLIGHTS

On 1989-91 vehicles, the headlights can be aimed using the adjusting screws located above and to the side of the headlight bulbs. A rough adjustment can be made while shining the headlights on a wall or on the rear of another vehicle, but headlight adjustment should really be made using proper headlight aiming equipment.
On 1992-98 vehicles, the aerodynamically styled headlights necessitate the use of headlight aiming kit 107-00003 or equivalent. The adjustable aimer adapters provided in the kit must be used to aim the headlights. Adjustment aimer adapter positions are moulded into the bottom edge of the headlight lens. Set and lock the adjustable adapters, attach each adapter to its mechanical aimer and aim the headlights according to the instructions in the kit.
Headlight aim adjustment should be made with the fuel tank approximately half full, the vehicle unloaded and the trunk empty, except for the spare tire and jacking equipment. Make sure all tires are inflated to the proper pressure.
The headlights must be properly aimed to provide the best, safest road illumination. The lights should be checked for proper aim and adjusted as necessary. Certain state and local authorities have requirements for headlight aiming; these should be checked before adjustment is made.

CAUTION About once a year, when the headlights are replaced or any time front end work is performed on your vehicle, the headlight should be accurately aimed by a reputable repair shop using the proper equipment. Headlights not properly aimed can make it virtually impossible to see and may blind other drivers on the road, possibly causing an accident. Note that the following procedure is a temporary fix, until you can take your vehicle to a repair shop for a proper adjustment.
Headlight adjustment may be temporarily made using a wall, as described below, or on the rear of another vehicle. When adjusted, the lights should not glare in oncoming car or truck windshields, nor should they illuminate the passenger compartment of vehicles driving in front of you. These adjustments are rough and should always be fine-tuned by a repair shop which is equipped with headlight aiming tools. Improper adjustments may be both dangerous and illegal.
For most of the vehicles covered by this guide, horizontal and vertical aiming of each sealed beam unit is provided by two adjusting screws which move the retaining ring and adjusting plate against the tension of a coil spring. There is no adjustment for focus; this is done during headlight manufacturing.
Because the composite headlight assembly is bolted into position, no adjustment should be necessary or possible. Some applications, however, may be bolted to an adjuster plate or may be retained by adjusting screws. If so, follow this procedure when adjusting the lights, BUT always have the adjustment checked by a reputable shop.
Before removing the headlight bulb or disturbing the headlamp in any way, note the current settings in order to ease headlight adjustment upon reassembly. If the high or low beam setting of the old lamp still works, this can be done using the wall of a garage or a building:
  1. Park the vehicle on a level surface, with the fuel tank about 1 / 2 full and with the vehicle empty of all extra cargo (unless normally carried). The vehicle should be facing a wall which is no less than 6 feet (1.8m) high and 12 feet (3.7m) wide. The front of the vehicle should be about 25 feet from the wall.

See Figure 6


1ad3b8e.jpg
Fig. 6: Example of headlight adjustment screw location for composite headlamps
  1. If aiming is to be performed outdoors, it is advisable to wait until dusk in order to properly see the headlight beams on the wall. If done in a garage, darken the area around the wall as much as possible by closing shades or hanging cloth over the windows.
  2. Turn the headlights ON and mark the wall at the center of each light's low beam, then switch on the brights and mark the center of each light's high beam. A short length of masking tape which is visible from the front of the vehicle may be used. Although marking all four positions is advisable, marking one position from each light should be sufficient.

See Figures 7 and 8


9018da5.jpg
Fig. 7: Low-beam headlight pattern alignment


fa6b141.jpg
Fig. 8: High-beam headlight pattern alignment
  1. If neither beam on one side is working, and if another like-sized vehicle is available, park the second one in the exact spot where the vehicle was and mark the beams using the same-side light. Then switch the vehicles so the one to be aimed is back in the original spot. It must be parked no closer to or farther away from the wall than the second vehicle.
  2. Perform any necessary repairs, but make sure the vehicle is not moved, or is returned to the exact spot from which the lights were marked. Turn the headlights ON and adjust the beams to match the marks on the wall.
  3. Have the headlight adjustment checked as soon as possible by a reputable repair shop.

Hope thats helped (remember rated this) Good luck.

Jan 24, 2010 | 1997 Mercury Grand Marquis

5 Answers

How do i adjust my headlingt on a 2001 suzuki xl7


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Nov 14, 2009 | 2001 Suzuki Xl 7

1 Answer

How do you align or focus headlights beams that are to


AIMING THE HEADLIGHTS

The headlights must be properly aimed to provide the best, safest road illumination. The lights should be checked for proper aim and adjusted as necessary. Certain state and local authorities have requirements for headlight aiming; these should be checked before adjustment is made.

CAUTION About once a year, when the headlights are replaced or any time front end work is performed on your vehicle, the headlight should be accurately aimed by a reputable repair shop using the proper equipment. Headlights not properly aimed can make it virtually impossible to see and may blind other drivers on the road, possibly causing an accident. Note that the following procedure is a temporary fix, until you can take your vehicle to a repair shop for a proper adjustment.
Headlight adjustment may be temporarily made using a wall, as described below, or on the rear of another vehicle. When adjusted, the lights should not glare in oncoming car or truck windshields, nor should they illuminate the passenger compartment of vehicles driving in front of you. These adjustments are rough and should always be fine-tuned by a repair shop which is equipped with headlight aiming tools. Improper adjustments may be both dangerous and illegal.
For most of the vehicles covered by this guide, horizontal and vertical aiming of each sealed beam unit is provided by two adjusting screws which move the retaining ring and adjusting plate against the tension of a coil spring. There is no adjustment for focus; this is done during headlight manufacturing.
Because the composite headlight assembly is bolted into position, no adjustment should be necessary or possible. Some applications, however, may be bolted to an adjuster plate or may be retained by adjusting screws. If so, follow this procedure when adjusting the lights, BUT always have the adjustment checked by a reputable shop.
Before removing the headlight bulb or disturbing the headlamp in any way, note the current settings in order to ease headlight adjustment upon reassembly. If the high or low beam setting of the old lamp still works, this can be done using the wall of a garage or a building:
  1. Park the vehicle on a level surface, with the fuel tank about 1 / 2 full and with the vehicle empty of all extra cargo (unless normally carried). The vehicle should be facing a wall which is no less than 6 feet (1.8m) high and 12 feet (3.7m) wide. The front of the vehicle should be about 25 feet from the wall.

fbcb5a7.jpg

Fig. : Location of the aiming screws on most vehicles with sealed beam headlights


97dee4f.jpg

Fig. : Dual headlight adjustment screw locations-one side shown here (other side should be mirror image)

9a545e8.jpg

Fig. : Example of headlight adjustment screw location for composite headlamps
  1. If aiming is to be performed outdoors, it is advisable to wait until dusk in order to properly see the headlight beams on the wall. If done in a garage, darken the area around the wall as much as possible by closing shades or hanging cloth over the windows.
  2. Turn the headlights ON and mark the wall at the center of each light's low beam, then switch on the brights and mark the center of each light's high beam. A short length of masking tape which is visible from the front of the vehicle may be used. Although marking all four positions is advisable, marking one position from each light should be sufficient.

031bc2f.jpg

Fig. : Low-beam headlight pattern alignment

758eed8.jpg

Fig. : High-beam headlight pattern alignment

  1. If neither beam on one side is working, and if another like-sized vehicle is available, park the second one in the exact spot where the vehicle was and mark the beams using the same-side light. Then switch the vehicles so the one to be aimed is back in the original spot. It must be parked no closer to or farther away from the wall than the second vehicle.
  2. Perform any necessary repairs, but make sure the vehicle is not moved, or is returned to the exact spot from which the lights were marked. Turn the headlights ON and adjust the beams to match the marks on the wall.
  3. Have the headlight adjustment checked as soon as possible by a reputable repair shop.

Hope helped with this information. Good luck (remember rated this help).

Nov 10, 2009 | 1996 Toyota Camry

1 Answer

How do you adjust the headlights on a 1998 ford F250 pickup


AIMING THE HEADLIGHTS
The headlights must be properly aimed to provide the best, safest road illumination. The lights should be checked for proper aim and adjusted as necessary. Certain state and local authorities have requirements for headlight aiming; these should be checked before adjustment is made.

CAUTION About once a year, when the headlights are replaced or any time front end work is performed on your vehicle, the headlight should be accurately aimed by a reputable repair shop using the proper equipment. Headlights not properly aimed can make it virtually impossible to see and may blind other drivers on the road, possibly causing an accident. Note that the following procedure is a temporary fix, until you can take your vehicle to a repair shop for a proper adjustment.
Headlight adjustment may be temporarily made using a wall, as described below, or on the rear of another vehicle. When adjusted, the lights should not glare in oncoming car or truck windshields, nor should they illuminate the passenger compartment of vehicles driving in front of you. These adjustments are rough and should always be fine-tuned by a repair shop which is equipped with headlight aiming tools. Improper adjustments may be both dangerous and illegal.

For most of the vehicles covered by this guide, horizontal and vertical aiming of each sealed beam unit is provided by two adjusting screws which move the retaining ring and adjusting plate against the tension of a coil spring. There is no adjustment for focus; this is done during headlight manufacturing.


Because the composite headlight assembly is bolted into position, no adjustment should be necessary or possible. Some applications, however, may be bolted to an adjuster plate or may be retained by adjusting screws. If so, follow this procedure when adjusting the lights, BUT always have the adjustment checked by a reputable shop.
Before removing the headlight bulb or disturbing the headlamp in any way, note the current settings in order to ease headlight adjustment upon reassembly. If the high or low beam setting of the old lamp still works, this can be done using the wall of a garage or a building:

Park the vehicle on a level surface, with the fuel tank about 1 / 2 full and with the vehicle empty of all extra cargo (unless normally carried). The vehicle should be facing a wall which is no less than 6 feet (1.8m) high and 12 feet (3.7m) wide. The front of the vehicle should be about 25 feet from the wall. 5374ba7.jpg

Fig. Example of headlight adjustment screw location for composite headlamps


If aiming is to be performed outdoors, it is advisable to wait until dusk in order to properly see the headlight beams on the wall. If done in a garage, darken the area around the wall as much as possible by closing shades or hanging cloth over the windows. Turn the headlights ON and mark the wall at the center of each light's low beam, then switch on the brights and mark the center of each light's high beam. A short length of masking tape which is visible from the front of the vehicle may be used. Although marking all four positions is advisable, marking one position from each light should be sufficient. 30c25df.jpg

Fig. Low-beam headlight pattern alignment


683f51e.jpg

Fig. High-beam headlight pattern alignment

If neither beam on one side is working, and if another like-sized vehicle is available, park the second one in the exact spot where the vehicle was and mark the beams using the same-side light. Then switch the vehicles so the one to be aimed is back in the original spot. It must be parked no closer to or farther away from the wall than the second vehicle. Perform any necessary repairs, but make sure the vehicle is not moved, or is returned to the exact spot from which the lights were marked. Turn the headlights ON and adjust the beams to match the marks on the wall. Have the headlight adjustment checked as soon as possible by a reputable repair shop.
Hope helped with this (remember rated this help) Good luck.

Oct 30, 2009 | 1997 Ford Explorer AWD

3 Answers

How do i adjust the headlight beam on my Subaru Forester X MY06 Model


on each headlamp assembly, there will be either one or two plastic nuts that you can turn.

If you only have one nut on each, that will adjust the vertical aim of the headlights.

If you have two nuts on each, one will adjust the vertical and the other will adjust the horizontal.

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Apr 26, 2009 | 2006 Subaru Forester

1 Answer

How to adjust headlight of Honda 2005


open the hood by the lights u will see a hole wth a light symbl near it put a long screwdriver in and turn the click wheel thing that will raise/lower the whole headlight assembly. ADJUST THE LOW BEAMS BECAUSE THE WHOLE ASSEMBLY MOVES HIGHBEAMS ARE NOT AS IMPORTANT

Jun 15, 2008 | 2005 Honda Civic

Not finding what you are looking for?
1994 Toyota Camry Logo

Related Topics:

376 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...