Question about 1992 Ford LTD

2 Answers

Timeing just changed a dizy on a 1992 ford 4.0 and need to know what position to put the rotor in

Posted by on

  • shaza_1 Nov 15, 2008

    thanks, thats what i would have done if it was a holden, in the dizy fords have marked start & finish which didn't make sense as "finish was at 1 n start was at 3.


2 Answers

  • Level 1:

    An expert who has achieved level 1.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Make sure you motor is on top dead centre before putting dizzy back in other wise you will be 180 deg out and will back fire flat out

Posted on Feb 05, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has achieved Level 3.

  • Master
  • 426 Answers

If you have made sure that the timing marks were set right on harmonic balancer before removing distributor then point the rotor toward the terminal/H/T lead that leads to no.1 plug.There should be a mark on the distributor that indicates no.1 position.Its just a line in the distributor where the cap sits on the distributor.

Posted on Nov 11, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Camshaft torque specs on a 1992 Toyota 4runner

Hi there:
The camshaft position sensor is installed on the front of the right cylinder head of the 5VZ-FE engine. The timing rotor has been integrated with the right bank camshaft timing pulley. While the camshaft rotates, the air gap between the protrusion on the timing rotor and the pick-up coil changes.

After replavcement procedure, attach the camshaft position sensor to the engine, tighten to 69 inch lbs. (8 Nm).

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Feb 09, 2012 | 1992 Toyota 4Runner

1 Answer

What is the firing order on a 92 Ford ranger xlt 3.0 v6

The spark plug firing order is ( 1 - 4 - 2 - 5 - 3 - 6 ) The distributor rotor turns CLOCKWISE ( 1 - 4 - 2 - 5 - 3 - 6 ) The marked # 1 position on the distributor cap faces towards the firewall and slightly towards the passenger side The engine cylinders / spark plugs are numbered : passenger side of engine , front to rear , 1 , 2 , 3 and drivers side of engine , front to rear , 4 , 5 , 6

Dec 08, 2010 | 1992 Ford Ranger

2 Answers

When install the new distributor for 1992 honda accord dx, do i have to align the TDC? or just loose the 3 screws and pop out and pop in?

no you have to time it up ,take no1 spark plug out ,use a thin screwdriver to find TDC ,see where rotor points too then install new one to the same position ,simple

Apr 08, 2010 | 1992 Honda Accord

2 Answers

Tools needed to change rotors

You might require Brake caliper along with the basic tools to work on bolts.


Aug 28, 2009 | 1998 Ford Explorer

1 Answer

I can't get the hub off to replace the rotor.

4X4?..Then you have to remove the lock-out,then use a hub socket which is about 3 inches in diameter with 4 notches in it to remove the ratchet nut inside the hub..then after the hub is off,put a lug nut on the studs and hammer them down out of the hub and the hub should come may have to hammer on the hub all the way around because the rotor and hub fit together pretty tight.

May 17, 2009 | 1992 Ford F150 SuperCab

1 Answer

Honda prelude 1992 2.3

very easy remove distributor cap inside notice the position of the rotor when instaling it back need to be at the same place remove electrical wire remove bolt remove distributor 2 thing you have to do notice the place of rotor if not car wont start and put the distributor in the same position with the bolt holding it if not timing will be off good luck hope it FIXYA pierre

Jul 05, 2008 | 1994 Honda Prelude

Not finding what you are looking for?
1992 Ford LTD Logo

Related Topics:

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

63577 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers


Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides