Question about 2001 Jeep Grand Cherokee

1 Answer

My 2001 jeep wrangler transmisson wont engage drive...

My 2001 jeep wrangler transmisson wont go into drive, but reverse works just fine. the fluid looks fine, and the color looks fine. i was driving when it suddenly just slipped out of gear. i had to reverse 2 blocks to get home. it didnt make any noises when it slipped. what could be some of the problems?

Posted by on

  • theonlygilli Nov 11, 2008

    it is an automatic

  • Anonymous Mar 14, 2014

    Forward gears work fine,no slipping at all.Put it in reverse and nothing.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 475 Answers

Is this an auto or standard tranny?

Posted on Nov 11, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 jeep wrangler 4x4 auto...transmission is not engaging at all, i.e.not in park, drive, reverse, 2wd, 4hi or 4low...how do I fix it?


Did you check your ATF level? I have an ATF leak somewhere and when my ATF gets really low my auto trans will keep slipping out of gear until I dump another quart or two of ATF fluid into the trans.

Aug 16, 2010 | 2003 Jeep Wrangler

2 Answers

Car stuck in drive but wont go forward but reverse works fine


all you can do is check the fluid. if its ok then you will need a shop to diagnose it

Nov 14, 2009 | 2004 Buick Rendezvous

1 Answer

2001 jeep grand cherokee wont reverse in


This could be an issue with the shift solenoid , but can also be caused by low fluid due to a leak, check your fluid. Is there a check engine light on, if there is it could be a solenoid issue.

Aug 26, 2009 | 2001 Jeep Grand Cherokee

1 Answer

Problem going into gear


Your clutch system works the same as brakes do. The necessity to bleed tells you that there is a malfunction permitting air into the system. Check where the pedal rod goes into the firewall under the dash, the line itself, and the slave unit (some are inside the bellhousing...look for fluid dripping from bottom to verify if leaking) Not unlike brake master, they can also internally bypass. If you find no leaks, change master. Bleed system and you should be fine

Jul 11, 2009 | 1995 Jeep Wrangler

1 Answer

1992 jeep wrangler has no revers


check your linkage from shifter to transmission.or if its a cable shift the cable may be broken.Smell the transmission fluid see if it smells burnt.if so then tranny reverse has went up

Jun 11, 2009 | 1992 Jeep Wrangler

1 Answer

How do you know if your torque converter is bad on Jeep wrangler


First check fluid. Make sure it's full and clean and does not smell burned (compare to another good car)
Converter failure is usually most obvious when trans shifts to OD. if shift is late or makes bang noise going in, you likely have a problem. to check lockup, after od engages, lightly touch brake, trans should momentarily shift out of od. Whining is usually due to low fluid. Also check transfer case and both differentials for proper level and leaks.

Jan 24, 2009 | 1998 Jeep Wrangler

1 Answer

91 wrangler 4 wheel will not engage


Check your fluid levels, you need to verify that the transfer case has fluid in it. Also, on one of my old jeeps the lever that put it into 4 wheel drive just stuck a litle. After yanking the **** out of it and moving it back and forth, drive a litle then stop and do it all over again.. a few times. it went into 4 wheel drive. this is why you are suposed to engage your 4 wheel drive once a month and drive around the block, just to make sure it gets flid where its supose to. if it doesn't get engaged then the fluid just sits at the bottum of the transfer case and doesn't get up on the gears.

Dec 20, 2008 | 1991 Jeep Wrangler

Not finding what you are looking for?
2001 Jeep Grand Cherokee Logo

316 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...