Need to change a parking bulb in front head lamp and can't figure out how to get it off or get into the bulb area

The fuses for right and left are seperate, have you checked them?
Is this both front and rear, do the turn signals work?
Is it safe to assume you mean the running lights, without the head lamps on? Does your vehicle have the fog lamps too or is this a base model?

I know some Renaults such as the Megane have an access port within the wheel arch. You might try checking there. If there is one though, then it's likely easier to take the wheel off to get to it.

The issue is most likely the turn signal switch.

TAKE THE HOLE HEADLIGHT OUT AS THIS SHOULD BE ONE ASSEMBLY THIS WILL LET GET TO THE PARKING LIGHT

Hi, viewer. In my practice, I was able to change the high beam bulbs and signal bulbs by removing the forward portion of the front wheelhouse liner. Lots of patience though. The low beam bulbs and the park lamp bulbs is somewhat difficult to reach, may even require removal of the whole assembly especially if the lowbeam bulb connectors are burned.

Removal & Installation

1. Disconnect the negative battery terminal.
   

2. Remove the head lamp mounting bolts, then disconnect the lamp connectors.
   

3. Replace the head lamp bulb(A), position bulb(B) and turn signal bulbs(C).
   

   Head lamp bulb(A), position bulb(B) and turn signal bulbs(C)
   

4. To install, reverse removal procedure.
   

Lamps, Parking Front Lamp-Lamp Assembly, Taurus
Removal and Installation

1. Remove Headlamp (13008) as outlined.
   

Headlamp Assembly
Removal and Installation

1. WARNING: THE REPLACEABLE HALOGEN HEADLAMP BULB CONTAINS GAS UNDER PRESSURE. THE HALOGEN HEADLAMP BULB MAY SHATTER IF THE GLASS ENVELOPE IS SCRATCHED OR THE HALOGEN HEADLAMP BULB IS DROPPED. HANDLE HALOGEN HEADLAMP BULB CAREFULLY. GRASP HALOGEN HEADLAMP BULB ONLY BY ITS PLASTIC BASE. AVOID TOUCHING GLASS ENVELOPE. KEEP HALOGEN HEADLAMP BULB OUT OF REACH OF CHILDREN.
   Position headlamp switch (11654) and headlamp time delay switch (13736) in the OFF position.
   

1. Remove two bolts retaining headlamp (13008) to upper support assembly and loosen pinch bolt. Remove headlamp assembly from vehicle.
   

1. Remove park lamp bulb and socket (Sable only) and headlamp bulb and socket from Headlamp Assembly as outlined.
   
   
   Headlamp Assembly (Taurus Shown, Sable Similar)
   
   
   
   

1. Turn lamp socket and wiring (13410) assembly 1/2 turn counterclockwise and remove from parking lamp (13200) housing.
   

1. Remove screw from park/turn signal housing.
   

1. Using 1/4 inch drive socket extension and swivel, insert tool through two access holes in upper radiator support. Remove screws from park/turn signal housing.
   

1. Remove parking lamp from vehicle.
   

1. To install, reverse Removal procedure.
   
   
   Front Lamp-Lamp Assembly, Taurus
   
   
   

this is regarding low beam head lamps. i have a 2006 kia optima and to change the head lamp, there is a cap right behind the head lamp area that screws off. remove the connection to the head lamp. oncece the cap is unscrewed and the connection is removed, you will see a clamp that keeps the lamp bulb in place. save yourself the headache and do not unscrew this clamp as it is aggrivating to screw back into place....on the opposite side of the screw u can push on the clamp ( i think it is downward) and it will swivel one side away from the lamp bulb, just that side, while the screw side keeps the clamp in place. remove the bulb, place your new on into place (there are 3 notches on the metal part of the lamp bulb that sit into place. take a look and u will see how they need to sit.) replace the clamp, replace the connection and screw cap back on and you are finished. the first time took a minute to figure out, but once u do it, it only takes about 5 minutes to do after that first initial time.

I hope you were asking about the head lamp.Depending what style you have .If you look at the front and see four screws and the headlamps have a chrome bezel around it then you will have to take the whole light out the front.If both head lamps are one piece then the bulbs gets removed from the back.Squeeze and turn then remove the wireing harness.

1. From under front wheelhouse, remove access cover behind park and turn signal lamp
2. Through access hole in wheelhouse, rotate park and turn signal socket counterclockwise one quarter turn.
   1. Pull socket from back of lamp.
   2. Pull bulb from socket. INSTALLATION
      
      1. Align key on bulb base to groove in socket and insert bulb into socket.
      2. Through access hole in wheelhouse, insert socket into back of lamp.
      3. Rotate park and turn signal socket clockwise one quarter turn.
      4. Install access cover and verify lamp operation.

Hope this helps with your prob