Question about 1999 Ford Windstar

1 Answer

Windshield wiper motor

Can you give me step by step instructions on how to remove old motor and replace new windshield wiper motor?

Posted by on

  • francis rivero May 11, 2010

    i would not know the exact for the 1999 windstar but i could give you the basic for any car.

    would you like that?

    drcool


  • Anonymous Mar 15, 2014

    windshield wipers for a xuv 55- s4 instructions

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Easy done . Remove wiper arms with the hood closed. Open the hood. there a number of press clips that look like philips screws. on the front of the wiper plastics, remove them, remove the rubber trim. lift off the top plastics revealing the bottom fixing. there are 4 8mm bolts that you need to remove and remove the air and water vent screws. waggle the scection loose, remove the washer pipes from passenger side and off the jets, unclip the harness of the wiper motor and you can then remove from the car

Posted on Nov 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is my windshield wipers running in the off position, it's like they are running in the intermittent position, but it's in the off position.


When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Schematic Reference: Wiper/Washer Schematics


1

Did you review the Wiper/Washer System Description and Operation and perform the necessary inspections?
Go to Step 2
Go to Symptoms - Wiper/Washer Systems

2

  1. Turn the ignition ON.
  2. Turn the windshield wiper/washer switch OFF.
Are the windshield wipers always on?
Go to Step 3
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

3

Disconnect the windshield wiper/washer switch connector.
Are the windshield wipers always on?
Go to Step 4 if yes
Go to Step 7 if no

4

  1. Disconnect the windshield wiper motor connector.
  2. Test the windshield wiper switch signal 1 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 5

5

Test the windshield wiper switch signal 2 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 6

6

Test the windshield wiper motor high speed circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 9

7

Inspect for poor connections at the windshield wiper/washer switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 8

8

Replace the windshield wiper/washer switch. Refer to Windshield Wiper and Washer Switch Replacement - On Vehicle in Steering Wheel and Column.
Is the repair complete?
Go to Step 11
--

9

Inspect for poor connections at the windshield wiper motor. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 10

10

Replace the windshield wiper motor. Refer to Windshield Wiper Motor Replacement .
Is the repair complete?
Go to Step 11
--

11

Operate the system in order to verify the repair.
Did you correct the condition?
The Wiper / Washer System consists of the following components:
?€¢
Windshield wiper / washer switch


?€¢
Windshield wiper system module / motor


?€¢
Windshield washer fluid pump


?€¢
Windshield washer fluid level switch


?€¢
Instrument panel cluster (IPC)


?€¢
ACC 15-amp fuse


?€¢
WSW 30-amp fuse

Jan 04, 2016 | 2002 Pontiac Bonneville

2 Answers

How to replace a 99 se Bonneville windshield wiper motor


Windshield wiper motors are generally easy to replace. You need to remove the windshield wipers and take off the small grill panel above the hood and under the windshield. You should see the motor in there. It simply unbolts and unplug the electrical connector and replace it with a new one.

Mar 21, 2015 | 1999 Pontiac Bonneville

2 Answers

How do you replace windshield wiper motor on a 1997 ford e250 van


REMOVAL
  1. Raise and support the hood.
  2. Remove the windshield wiper pivot arms.
  3. Remove the cowl top vent panels.

25287270-15uk5heqgoha5mc4ejw3dmql-1-0.gif
  1. Disconnect the windshield wiper mounting arm and pivot shaft.
  1. Remove the access cover from the dash panel.
  2. Remove the mounting arm and pivot shaft retaining clip.
  3. Disconnect the windshield wiper mounting arm and pivot shaft from the windshield wiper motor.

25287270-15uk5heqgoha5mc4ejw3dmql-1-2.gif
  1. Remove the windshield wiper motor.
  1. Disconnect the electrical connector.
  2. Remove the three bolts.
  3. Remove the windshield wiper motor.
INSTALLATION

25287270-15uk5heqgoha5mc4ejw3dmql-1-5.gif
  1. Install the mounting arm and pivot shaft retaining clip on the windshield wiper mounting arm and pivot shaft.

25287270-15uk5heqgoha5mc4ejw3dmql-1-9.gif
  1. Install the windshield wiper motor.
  1. Place the windshield wiper motor in the dash panel.
  2. Install the three retaining bolts.
  3. Reconnect the electrical connector.

25287270-15uk5heqgoha5mc4ejw3dmql-1-14.gif
  1. Reconnect the windshield wiper mounting arm and pivot shaft.
  1. Press on the windshield wiper mounting arm and pivot shaft after it is aligned with the windshield wiper motor.
  2. Install the access cover in the dash panel.
  1. Install the cowl top vent panels.
  2. Install the windshield wiper pivot arms.
  3. Adjust the windshield wiper pivot arms.
This is technically for the V6 4.2L but I'm sure those Ford E250's have the same setup for windshield wiper motor. Let me know how it goes.

Nov 17, 2014 | Cars & Trucks

1 Answer

How to replace the wiper motor on a 1994 volkswagon golf


The wiper motor on a Volkswagen is an electric motor connected through a drive linkage to the wiper arms. Windshield wipers are an integral feature for operating a motor vehicle safely. If your wipers are not functioning, or seem to lack the speed or power they used to have, the wiper motor should be removed and replaced immediately
.


Location
  • The wiper motor on a Volkswagen is located directly underneath the plastic cowl cover. The cowl cover is located directly below the windshield.

Removal
  • Begin by removing the wiper arms by prying off the covers at the base of the arms and removing the nuts that secure the arms to the drive shafts. Label the passenger and driver arms so they can be installed in the same positions. They are not interchangeable. Remove the rubber hood to cowl weather seal. Unscrew the plastic fasteners from the driver's side of the cowl cover, then remove this half of the cover. Remove the fasteners from the passenger's side cowl cover and remove this half of the cover. Disconnect the windshield wiper motor wiring harness by separating the plastic wiring connector. Remove the three bolts that secure the wiper motor to the vehicle's body. Pull the motor slightly away from the body, then remove the nut that connects the motor shaft to wiper linkage. Remove the motor.

Installation
  • Place the new wiper motor into position in the cowl and reconnect it to the wiper arm linkage. Then reinstall the three retaining bolts. Reconnect the plastic wiring connector to the wiper motor wiring harness. Place the cowl covers into position below the windshield and reinstall the plastic fasteners that retain them. Reinstall the rubber hood to the cowl weather seal. Reinstall the wiper arms in the same position you removed them from, along with the wiper arm retaining nuts and lower wiper arm covers. Turn the windshield wipers on and test for proper operation. If the wiper blades slap against the bodywork surrounding the windshield, loosen the nuts that connect the wiper arms to the shafts and adjust.

More Read: OBD2 car diagnostic tool

Aug 06, 2012 | 1994 Volkswagen Golf

1 Answer

Can you please give me instructions on replacing the wiper motor pulse board module on my 95 Chevy Van G20?


This is a very simple procedure and will save you lots of money by replacing it yourself! A common replacement item on GM vehicles, it should be readily available at your local auto parts retailer and should take no more than a half-hour with just a couple of tools.


• Turn the ignition key to the OFF position.
• Remove the Connector Position Assurance (CPA) and disconnect the wiper motor electrical connector.
atye.gif
• Remove the three screws that secure the cover to the wiper motor and remove the cover.
• Inspect for sealant on the inside of the cover and then discard the cover and screws. Important: If sealant was found on the old cover, it will be necessary to remove any old sealant from the motor housing in Step 6.
• Carefully remove the module (circuit board) from the wiper motor by lifting up on the end of the module electrical connector.
• If necessary, remove any old sealant from the wiper motor housing (refer to Step 4). Notice: When handling the new module in the next step, be careful not to damage or band the electrical contacts on the bottom side of the module.
• Install the module into the wiper motor housing, making sure that the module is fully seated. When fully seated, the edges of the module circuit board will be flush (even) with the motor housing along all sides.
atye_0.gif
• Carefully apply a bead of silicone sealant, P/N 12345739 (or GE-162 sealant or equivalent) in the groove of the NEW cover (Figure 2). Remove any excess sealant that is outside of the groove. Important: Only apply enough sealant to fill the groove in the cover.
Install the new cover on the wiper motor housing and install the three new screws.
• Tighten the screws to 2.6 N·m (23 lb in).
• Reconnect the wiper motor electrical connector to the wiper motor assembly and install the CPA.
• Turn the ignition key to the ON position and check the wiper system for proper operation (delay/low/high/etc.).



May 04, 2011 | Chevrolet G20 Cars & Trucks

2 Answers

How do you remove and replace windshield wiper 2007 Honda Civic


the Windshield wiper blades have little clips that lock them in place. Most replacements have direction on how to release these, as they are common to all models, and remove and install the new ones. If you are talking about the Windshield wiper motor itself i recommend you get a Haynes repair manual on your vehicle so you have the step by step instruction on how to remove and replace this part.

Nov 22, 2009 | 2007 Honda Accord Sedan

1 Answer

I cant figure out how to change my windshield wiper blades on 2001 ford ranger


How to Replace Wiper Blades Guide (Typical):
Potential tools needed to replace wiper blades:
  • Flat blade screwdriver (small)
  • Small nosed pliers
  • Latex or vinyl gloves
  • Safety goggles
To replace wiper blades theactual action of replacing the blade is no big deal, it's the locationof the blade down below the hood that can make it difficult though.Sometimes it helps to open the hood to gain access to the wiper blades.Other times it is helpful if the wiper blade is somewhere in the motionline of wiper action. The trick is to get the wiper to stop somewherein the wiper arc. Turn the wipers to the on position and allow thewipers to start, and then shut the key off when the wiper has arrivedin a desirable position on the windshield. To replace your wiper bladesplease follow the step by step instruction below. Also, watch the How to replace wiper blades video below to gain additional information. The method in which the wiper blades are attached will vary slightly.
  • Step 1: With the hood closed, turn the wiperson, when the wipers are in the middle of their arc turn the key to theoff position. (Note: if this can't be done because of wiper conditionand you want to avoid scratching the windshield please open your hoodto gain access)
  • Step 2: Locate the mounting clips at the top pivot on the wiper blade
  • Step 3: Release the clip and remove the wiper arm
  • Step 4: Match the size of the old blade against the new blade to ensure proper fit and operation
  • Step 5: Reinstall the new wiper blade and recheck wiper operation

Common Problems:
  • Make sure the wiper blades are the same size as the original blades.
  • When replacing wiper blades not getting the blade onthe mounting pin completely allowing the wiper arm to become dislodgedand possibly causing damage to the windshield.
  • Using wiper blades after the blade has failed permanently damaging the windshield by craving scratches in the wiper arc.
  • Wiper blade can create a chattering noise when theblade is not properly balanced allowing the blade to "flop" back andforth as the wiper direction changes.

I hope help you with this (remember rated this help) Good luck.

Sep 16, 2009 | 2001 Ford Ranger Regular Cab

2 Answers

How do I remove front wiper blades to replace with new ones on my 2006 nissan quest


How to Replace Wiper Blades Guide:
Potential tools needed to replace wiper blades:
  • Flat blade screwdriver (small)
  • Small nosed pliers
  • Latex or vinyl gloves
  • Safety goggles
To replace wiper blades the actual action of replacing the blade is no big deal, it's the location of the blade down below the hood that can make it difficult though. Sometimes it helps to open the hood to gain access to the wiper blades. Other times it is helpful if the wiper blade is somewhere in the motion line of wiper action. The trick is to get the wiper to stop somewhere in the wiper arc. Turn the wipers to the on position and allow the wipers to start, and then shut the key off when the wiper has arrived in a desirable position on the windshield. To replace your wiper blades please follow the step by step instruction below. Also, watch the How to replace wiper blades video below to gain additional information. The method in which the wiper blades are attached will vary slightly.
  • Step 1: With the hood closed, turn the wipers on, when the wipers are in the middle of their arc turn the key to the off position. (Note: if this can't be done because of wiper condition and you want to avoid scratching the windshield please open your hood to gain access)
  • Step 2: Locate the mounting clips at the top pivot on the wiper blade
  • Step 3: Release the clip and remove the wiper arm
  • Step 4: Match the size of the old blade against the new blade to ensure proper fit and operation
  • Step 5: Reinstall the new wiper blade and recheck wiper operation

Common Problems:
  • Make sure the wiper blades are the same size as the original blades.
  • When replacing wiper blades not getting the blade on the mounting pin completely allowing the wiper arm to become dislodged and possibly causing damage to the windshield.
  • Using wiper blades after the blade has failed permanently damaging the windshield by craving scratches in the wiper arc.
  • Wiper blade can create a chattering noise when the blade is not properly balanced allowing the blade to "flop" back and forth as the wiper direction changes.

I hope help you with this (remember rated this help) Good luck.

Sep 14, 2009 | 2006 Nissan Quest

1 Answer

Front winsheild wiper motor


unplug old motor
remove plastic at base of windshield
remove the nut that attaches the wiper arms to the motor
remove the three bolts that attach the motor to the firewall
install the new one by reversing these steps
Hope this helps!

Mar 05, 2009 | 1998 Chevrolet Suburban

1 Answer

Windshield wipers


According to AllData, you don't have to remove the motor to install a new switch. Subsequently, AllData doesn't give direction on wiper arm or motor removal. Here are the only diagrams they give for switch replacement.

41917584 41917585

Aug 04, 2008 | 1987 Cadillac Fleetwood

Not finding what you are looking for?
1999 Ford Windstar Logo

253 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...