Question about 2000 Chrysler Grand Voyager

1 Answer

I have a Chrysler GrandVoyager 2.5td. When driving the vehicle the gear change gets stiff and gears do not go in smoothly, mostly when vehicle is warm.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Not enough oil in the gearbox could be one reason

Posted on Nov 11, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My automatic transmission on a 1996 chrysler concorde lx will not change gears when taking off on occasion. Or it will go to a low gear when driving at about 30 mph or higher.


Yes, this is most likely a shift solenoid but I would do the dummy check on the fluid level first. Tranny oil also needs to be changed every 60000 miles on most vehicles.

Nov 02, 2016 | Chrysler Concorde Cars & Trucks

1 Answer

My gear is stiff and experiencing a difficulty when engaging second gear. other gears seems to be fine but the shifting is not smooth.


I suspect that it will be in the shift mechanism
If it is a cable shift then replace the cable
If it levers or other linkages check and adjust or lubricate as required
I doubt it is in the clutch as you haven't mentioned difficulty in selecting first gear only shifting from 1 to 2nd.

Jun 21, 2015 | Opel Corsa Cars & Trucks

1 Answer

My 2005 Audi A5 steering is get stiff after few minutes of starting in the morning. This is the situation even with enough power steering oil. The power steering doesn't work. The gear system also has a...


Check the gear box oil level sounds low to me i had a similar problem with a auto box car before and as for your steering it could be a worn steering rack if the oil level is good

Feb 03, 2015 | Audi A5 Cars & Trucks

2 Answers

Buick rendezvous gear shifts just fine but car won't move. No grinding shifting is smooth and flawless vehicle just will not move forward whether it is in drive, 1st, 2nd, or third gear. Reverses and


Sounds as if forward driving gears are shot. Different gears make vehicle move in reverse. I would ask if transmission fluid level when checked is in the operation range or full.

Nov 07, 2013 | Cars & Trucks

1 Answer

When I put my gear into Reverse, Netrual and Drive the gear is getting stiff to move. Why is this happening?


If you mean the shifter is getting hard to move, its probably the shift linkage sticking, try a couple squirts of pblaster or other penetrating oil. If the motion of the vehicle is getting hard to drive in reverse and drive the torque converter may be the issue.

Jun 03, 2012 | 2006 Ford Five Hundred

1 Answer

Landrover td5 54 plate gear problem local driving ok problem starts when on a run gears go stiff on tight run gearstick acroos in neutral and if feels like metal greating . swithch engine off and gears...


Have you checked the oil recently? I'd suggest changing it fully rather than topping up, and checking for any signs of metal in the oil (the drain plug should be magnetic, but running the oil into a plastic tub then sticking a magnet in to the oil and waving that round should find any not on the plug. Lots of Metal = Bad.

Feb 05, 2010 | 2004 Land Rover Discovery

2 Answers

ROUGH SHIFTING PT CRUISER


Some modern vehicles when change the shift pattern while the engine is cold, by keeping the vehicle in a lower gear for a higher rpm while the engine is cold, the engine warms up faster, to reduce emissions. (Emissions are higher while the vehicle is cold)

What you may be experiencing is that the shift from first to second occurs at a higher rpm when the engine is cold than when warm. This can lead to an abrupt or hard shift. At higher speeds, the shift between gears either may not be changed, or just does not feel as hard as the 1st to 2nd shift.

If this is the case, then your dealer is telling you the truth and there is nothing he can do.

Aug 26, 2009 | 2007 Chrysler PT Cruiser Touring Hatchback

2 Answers

I have a golf gti the gears are really stiff


try changeing the detent device ontop of the gear box. it is a 24 nut when u open it there will be a ball and spring attached to the other side. it is located ju8st behind the gear selcator on the very top of the gear box

Mar 05, 2009 | 1995 Volkswagen Golf

1 Answer

Gear shift stickinh


Sounds like the shifter cable is corroded to the point that it might snap. Replace the shifter cable. Best wishes to you.

Jan 21, 2009 | 2001 Chrysler 300M

Not finding what you are looking for?
2000 Chrysler Grand Voyager Logo

Related Topics:

245 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...