Question about 1992 Chevrolet C1500

1 Answer

1992 chev 1500 signal lights and brake lights quit working

At first there was a 10 second delay before the signal light would start to flash,now they don't work at all.Someone told me it could be a relay,but i dont know where that is located.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 44 Answers

If it is the turn signal flasher it should be located in the Front seating area, driver side, driver side of steering column, behind instrument cluster, mounted in convenience center. It is possible that there could be a bad ground too. Flasher would be the first thing to check.

Posted on Nov 10, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Dodge ram 1500 wiring diagram

Three places to look. 1) Brake lamp fuse, 2) Turn signal switch and 3) the brake pedal switch. Brake light power comes from the fuse up to the turn signal switch down to the brake lite switch on the brake pedal and then on to the light bulbs. Start by putting the 4 way flasher on. If the brake lites flash, then the bulbs are good. That eliminated the fuse too. so the problem is the other two.

Jan 24, 2014 | Cars & Trucks

1 Answer

I have a 1994 dodge ram 1500 and when I hit my brakes my turn signals quit working and when I turn on my lights my brake lights and turn signals quit working

sounds like 1 of the 2 switches is bad, try replacing the headlight switch first then if still having problems try brake switch on the brake pedal

Oct 01, 2013 | Dodge Ram 1500 Cars & Trucks

1 Answer

1997 silverado 350 vortec 1500 2 wd long bed brake lights go out, flashers and turn signals go out running lights go out. Have been fixed 3 times now and brake lights have gone out again have been...

does sound like a circuit board problem , only way to tell is get the circuit boards checked out for loose/cracked connection's faulty parts etc , check for continuity along the circuit to the brake light connector , this site might help you get started as i don't know your level of this type of work,
How to Find Fault in Circuit Board Techwalla com

Jun 03, 2017 | Cars & Trucks

1 Answer

On a 2002 dodge ram 1500 truck the brake lights and the turn signals and winshield wipers dont work the only brake light that works is above the cab. and the turn signal flashes on the dash like they are...

I suspect a bad multi function switch located in the left hand side of the steering column. This switch controls your high/low beams/wiper delay/windshield washer/turn signals and hazards.

Dec 31, 2009 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

2006 Chev Impala turn signals not working on rear lights, turn signal flashing at a faster rate than normal, No brake lights when pushing on brakes.

Two issues here, you will need to replace the flasher. this will correct the erratic turn signals.

Concerning the brake light. Make sure the bulbs are in working condition and, check the wiring harness for faults as well. if the bulbs and wires arr OK, replace the brake light switch.

You can test for proper current by pulling the brake light bulbs out the socket and, use the copper prongs inside the brake light socket for testing. use a volt meter and, hit the brake pedal and, see if the meter registers a current. if not, replace the wiring harness.

Jun 04, 2009 | 2006 Chevrolet Impala

1 Answer

No brake light's on my truck,just quit working,turn signals and running lights working,thinking it might be the brake switch.any suggestions? 2001 dodge 1500 quid cab.

Hmm, It might be the break switch, have you checked the light bolbs? are they working? try fit new lights in. Hope that helps mate.

May 07, 2009 | 1996 Dodge Ram 1500 Club Cab

1 Answer

1996 Chev Cavalier - Rear signal & brake light out on driver side

check the wires for a cut or something that may be shorting out the lights 

Dec 05, 2008 | 1996 Chevrolet Cavalier

1 Answer

1992 chev 1500 pickup

what is the berring called that holds the drive shaft together befor the diff

Nov 10, 2008 | 1992 Chevrolet C1500

1 Answer

2001 dodge ram 1500 brake lights

I would guess the brake fuse ( this does not use the same fuse as the tail lights/blinkers) or the ground for the brake light bulb.

Aug 13, 2008 | 2001 Dodge Ram 1500 Truck 2WD

Not finding what you are looking for?
1992 Chevrolet C1500 Logo

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

77932 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides