Question about 1987 Ford Bronco

2 Answers

87 bronco automatic window not working

I have an 87 ford bronco and the passenger window stopped working. How hard is it to replace the motor?

Posted by on

  • Anonymous Mar 22, 2014

    no motor for back windo



2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

It is easy there are only four rivets holding it on. If you cut them off it will be easy. Then all you need is the new motor, 4 bolts and 4 locking nuts. I'm not sure what size bolts and nuts, but I think they are 1/4 inch. I just replaced the one on my bronco.

Posted on Nov 16, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 491 Answers

Pretty easy

Posted on Nov 10, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the fuel pump relay on my 87 bronco 2. Is it on the passenger upper fender? Would this make the fuel pump not work?

Inside, on the passenger side of the trans tunnel, on the firewall, under the carpet is your shut off switch. Press the button on top. Hope this helps.

Jan 08, 2011 | 1987 Ford Bronco II

1 Answer

I'm trying to replace the power window motor on the passenger side in my '91 Ford Bronco. I've removed the door panel, but how do I get the rest off??

you have to take off the arm to get the motor off... normally its four bolts holding it on... two at the top and two at the bottom. you also may need to take the window off the track.

Nov 13, 2010 | 1991 Ford Bronco

1 Answer

Fuel pump shut off switch for a 1988 ford bronco

is located on the passenger side by the foot pannel i had to remove my inner pannel on mine to find it also on my 87 ford f-150 it was located directly above the e-break

Apr 30, 2010 | 1988 Ford Bronco II

1 Answer

Trying to correctly put vacuum lines on an 87 Ford Bronco w/302. Where does the PVC line supposed to lead to?

It goes behind the intake on the passenger side if you have fuel enjected motor it's a little bit tough to reach or even see but that's were the factory line runs

Jan 29, 2010 | 1987 Ford Bronco

1 Answer

89 ford bronco driver and passenger power windows roll down but wont roll up with out help they just sit thier and make a jerking motion up and down in the same spot

likely is an issue with the motor itself, or could possibly be due to dirt/rust in the way on the track. best to take the forward window panel out and check if it is blocking the way otherwise replace the power window motor.

Dec 28, 2009 | 1989 Ford Bronco

1 Answer

Windshield whipper fuse were is it for a 1987 ford bronco. Cant find whipper fuse to check it.

Below is the fuse lay out for 87 bronco, no wiper fuse is mentioned. if they do not work i would check to see if the wiper motor is getting power, if so then replace wiper motor

Oct 27, 2009 | 1987 Ford Bronco

1 Answer

Both driver and passenger pwr windows won't work.1990 bronco 2

see if you have power switches . then try replaceing the driver side switch frist. if that duse not work then you will have to re place the windo motors.

Jul 08, 2009 | 1990 Ford Bronco

1 Answer

Power window not working

It is easy to replace, there are four rivets holding it in place. I just replaced my window motor. I used a flat head screw driver to break of the rivets. You want to make sure the window is held in place while you remove the rivets. Once I removed the rivets it can out with out a problem. Then when I remounted it I used 4 bolts and four locking nut. I think they were 1/4 nuts and bolts.

Nov 10, 2008 | 1987 Ford Bronco

1 Answer

Passenger window motor '86 bronco

take off the door and replace it with manual doors or check bronco graveyard for a motor

Aug 27, 2008 | 1986 Ford Bronco

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

259 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

78919 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5675 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides