Question about BMW 318

1 Answer

I have ford xpedition 2000 whit p1892 cod, the 4x4 ligh is blinking

The escaner say the problem is a wire but i dont fine the GEM # c241 conecter in the car

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 24 Answers

    Dont really understand the question but from what I can see the GEM is involved. On this model it usually has to do with a windshield water leak allowing water to intrude into the GEM. Push up on the upper left hand side of the windshield and se if it moves. If it does the glass must be replaced to properly repair the leak. Then and only then do you replace the GEM and possibly the fuse box due to water damage.

Posted on Nov 11, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can you put a 1996 gem module into a 1998 ford explorer


Yes you can and if that GEM module doesnt work the 4X4 will flash or if you dont have the 4x4 your door lock controls wont operate

Nov 26, 2012 | 1998 Ford Explorer

1 Answer

Terminal 15 keeps blowing in my 2001 ford f150 supercrew 4x4 lariat i dont know what to do. wont go into gear, lights wont work, windows wont roll down. what should i do???


Central Junction Box / cab fuse panel Fuse 15 ( 5A ) feeds the GEM Module

A leaking windshield ( lower left hand corner ) can cause water to get on the back of the CJB, and corrode the pins to the GEM.

May 30, 2011 | Ford F-150 Cars & Trucks

1 Answer

I put my ford excursioninto 4 wheel drive and now it won't come out. It has the turnswitch control located on the dash


many things could affect it. there is an actuator on the transfer case. check to see that you have 12 volts to the big two prong connector when you select 2 or 4 wd. if you don't it could be the relays under the hood. they are called clockwise counter clockwise relays. it could also be the GEM/ 4x4 control module. in a 2000 it is mounted behind the fuse box, left side of dashboard. I just went throught his with mine. it was the GEM.

May 13, 2010 | 2000 Ford Excursion

1 Answer

What do you do if the gem box for the 4wd has gone bad and the 4wd lights blink on the dash? My understanding is ford no longer makes the gem box. What do I do? Can I by pass it to make my 4wd work?


If the GEM is bad it will need to be replaced and programmed at the dealer. There is no way to bypass it to make the 4X4 work. You can try salvage yards,lkqonline.com or fordvintageparts.com

Feb 28, 2010 | 1997 Ford Explorer AWD

1 Answer

I have a 1996 Ford F 150 4x4 with the 5.0 v8. My


You need to remove the headlight swich and check the plug to it for burnt wire end,if none then replace the switch.

Nov 11, 2009 | 1996 Ford F150 Regular Cab

4 Answers

Location of GEM Module on 1998 Ranger


i am almost sure it is in steering col area by firewall. but call any part store like auto zone and they can print it out and tell you if your ford dealer wont. but on the fords they usualy are all in the drivers steering area sometimes way up by fire wall

Jun 15, 2009 | 2000 Ford Expedition

1 Answer

No interior lighting


All of these systems are controlled by the Generic Electronic Module, GEM for short, most likely it has failed, Ford can test it and determine what the problem is with it.

Aug 21, 2008 | 2000 Ford Expedition

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Fred Sops

Level 2 Expert

271 Answers

Al Clark

Level 2 Expert

290 Answers

Doberman

Level 2 Expert

246 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...