Question about 2004 Jeep Grand Cherokee

1 Answer

2004 Grand Cherokee Turn Signal Flasher

The hazard lights flash but turn signal do not 90% of time. Where is flasher and how to replace please.

Posted by on

  • 1 more comment 
  • mraymo2003 Nov 19, 2008

    I have the same exact problem

  • Anonymous Mar 14, 2014

    When I turn on either direction signal, the direction light comes on but the other direction id lightly lit up also and flashing. This happening on the inside and on the outside turn signals. This just started, I have gone through a few large puddles because here in Minnesota there is a rather large thaw going on.

  • Anonymous Mar 15, 2014

    flasher and hazard lights don't work

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

These have a flasher under the dash lower left side. 1. Remove lower trim 2. look for flasher plugged into fuse panel looks like a back plastic block about 1 in square with 9 prongs that plug in. 3. just replace. Part seems to be at least $30 I'm getting one for a friend.

Posted on Dec 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turn lights blink with hazards but not with turn signal..flasher replaced. is It the multifunction lever then??


There should be a turn signal flasher and a hazard flasher. They are two different parts. If you replaced the hazard flasher and not the turn signal flasher than I would start by replacing the turn signal flasher.

One thing you can do once you find the turn signal flasher is to unplug it and use a jumper wire between the two pins of the connector then turn the key to the run position and place the turn signal lever in the left or right position. If the turn signal lights know light up than the turn signal flasher is the problem

Sep 09, 2014 | 1997 Oldsmobile Cutlass Supreme

2 Answers

Have a 1988 Jeep Wagoneer with a few issues. My turn signals no longer blink or flash that I know of..?


Okay, the first thing to check is to turn on the signal on one side and see if the outside signal light comes on. if the light comes on then try replacing the flasher. Also see if your 4way flashers work or if they are also out. if they are out then check your fuse first.
If the fuses are good then try the flasher, if the flasher does not solve the problem then you may need to replace the turn signal switch. I have worked on a few of these and most of the time it was a flasher or the turn signal switch. good day.

Mar 02, 2012 | 1988 Jeep Cherokee

1 Answer

Turn signal will not flash


Check bulbs to see if all bulbs are lighting. Check to see if the Hazard lights flash. Replace flasher under dash for turn signal if bulbs are good and hazard flasher works. Otherwise, the turn signal switch might be bad in the steering column..

Nov 04, 2011 | 2004 Chevrolet Monte Carlo

1 Answer

1999 jeep grand cherokee - rear driver turn signal and brake light don't work. flasher, back up and running light works. everything works when lens assembly is plugged into the passenger side. can...


Check this diagram (click over pic for zoom)...

zjlimited_1040.jpg

Check the postion F4 / 15 Amp ( Lt. Blue ) Flasher, hazard switch (see Junction Block diagram above for location of turn signal Flasher relay - Mopar p/n 4686094)

Repair tip: WJ flasher repair.

Hope helps.

Apr 16, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

WHAT THE PROBLEM WHEN THE HAZARD LIGHTS OR THE TURN SIGNAL LIGHTS NOT COMING ON AT ALL...


You may want to check your hazard Turn signal flasher this is the component that causes your lights to flash.

Feb 16, 2011 | 2004 Pontiac Grand Am

2 Answers

Turn signals won't flash. They do come on but no intermittant flashing. Flasher has been swapped out. All turn signal lights come on on both sides front and back.


i think you may have replaced the hazard flasher not the turn signal flasher, the turn signal flasher is located behind the dash on the right side of the steering collum support, the hazard flasher is located in the convenience center.

Jan 14, 2011 | 1995 Chevrolet Cavalier

2 Answers

Turn signals hazards flasher don't work jeep cherokee replaced combination flasher relay, turn signal switch and still no signals


I NEED TO LOCATE THE SWITCH WHERE IS IT ?
MY INDICATORS NOR HAZARD LIGHTS ARE WORKING I DONT KNOW WHAT IS WRONG WITH IT CHANGED BULBS BUT NOTHIGN THEY ALL WENT OUT AT THE SAME TIME
SO THERE MUST BE A RELAY SWITCH SOMEWHER BUT DONT KNOW WHERE ?
THANKS FOR HELPING

Sep 27, 2009 | 1999 Jeep Cherokee

3 Answers

Turn signals wont work fuses are good?


the hazard switch above the radio is your problem. if you put on your signals and they don't flash turn hazards on then off and they will flash. (changing this *** will fix your problem

Aug 30, 2009 | 1999 Pontiac Grand Am GT

2 Answers

Indicator stays on


i am going to take it you are talking about the turn signal...look for a burned out bulb...that will cause this condition

Oct 30, 2008 | 2000 Jeep Grand Cherokee

2 Answers

Blinker wont work, but the hazards do


There are two thermal flashers one for the Hazard Warning Lights and one for the Turn signal lights. It could be the flasher for the turn signals.

Oct 26, 2008 | 1998 Jeep Grand Cherokee

Not finding what you are looking for?
2004 Jeep Grand Cherokee Logo

670 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...