Question about 2006 Toyota Corolla

1 Answer

Corolla bearings How do I get to the front wheel bearings on my 05 corolla?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 65 Answers

The front wheel bearings are pressed into the knuckle.You need to remove the axle nut,make sure to unstake the nut as to not damage the axle threads,and brake assembly,slide hammer the hub off then remove abs sensor if you have one then remove tie rod end,lower ball joint bolt and nuts,then the strut bolts.After the knuckle is off you will see a circlip on the inside by the bearing remove this then press the bearing out on a shop press.If you don't have a new hub you will also have to use a bearing splitter to get the bearing race off the hub to reuse it.Reverse process for reassembly.Hope that helps as it is not just a bolt on repair.

Posted on Nov 29, 2008

5 Suggested Answers

  • 117 Answers

SOURCE: toyota corolla

remove wheel
pop off centre cap
take out split pin
remove nut and you will be able to just pull the outer bearing out.
to get to the inner bearing you will need to take off the whole hub and do it off the car

Posted on Jun 30, 2008

  • 373 Answers

SOURCE: wheel bearing

HI, For replace the front wheel bearing. on a toyota corolla 03
You need a hydrualic bench.
Because they goin pressed.
I recomend go to a repair shop, is not easy.
It's take about 2 hour to do. with the right tools.

Posted on Jul 04, 2008

blueextc3221
  • 15935 Answers

SOURCE: replacing front wheel bearing

  1. Loosen the wheel nuts and the center axle nut.
  2. Raise the vehicle and safely support it.
  3. Remove the wheel. Remove the ABS speed sensor if so equipped.
  4. Unclamp the brake hose from the shock absorber, but do not disconnect the line.
  5. Remove the brake caliper and hang it out of the way on a piece of stiff wire. Do not disconnect the brake line; do not allow the caliper to hang by the hose.
  6. Remove the brake disc.
  7. Place a dial indicator near the center of the axle hub, and check the backlash in the bearing shaft direction. Maximum is 0.0020 inch (0.05mm). If the backlash exceeds the maximum, replace the bearing.
    1. Usiung a dial; indicator, check the deviation at the surface of the axle hub outside the hub bolt. Maximum is 0.0028 inch (0.07mm). If the deviation exceeds the maximum, replace the axle hub.
    2. Install the disc and caliper. Tighten to 65 ft. lbs. (88 Nm).
  8. Remove the cotter pin and install the wheel. Lower the vehicle to the ground.
  9. Remove the lock nut cap. While depressing the brake pedal, remove the center axle nut.
  10. Raise and support the vehicle again and remove the wheel, caliper and disc.
  11. Loosen the 2 nuts on the lower side of the shock absorber. Do not remove the 2 nuts and bolts.
  12. Remove the cotter pin and nut from the tie rod end.
  13. Remove the tie rod end from the knuckle using a joint separator or equivalent.
  14. Remove the bolt and 2 nuts holding the bottom of the ball joint to the control arm and separate the arm from the knuckle.
  15. Remove the 2 nuts from the steering knuckle. Place a protective cover or shield over the CV boot on the driveshaft.
  16. Using a plastic mallet, tap the driveshaft free of the hub assembly.
  17. Remove the bolts and remove the axle hub assembly.
    1. Clamp the knuckle in a vise with protected jaws.
    2. Remove the dust deflector. Loosen the nut holding the ball joint to the knuckle. Use a ball joint separator tool or equivalent to loosen and remove the joint
    3. Use a slide hammer/extractor to remove the outer oil seal.
    4. Remove the snapring.
    5. Using a hub puller and pilot tools or equivalents, pull the axle hub from the knuckle.
    6. Remove the brake splash shield (3 bolts).
    7. Use a split plate bearing remover, puller pilot and a shop press, remove the inner bearing race from the hub.
    8. Remove the inner oil seal with the same tools used to remove the outer seal.

    To install:
    1. Place the inner race in the bearing. Support the knuckle and use an axle hub remover with a plastic mallet to drive out the bearing.
    2. Clean and inspect all parts but do not wash or clean the wheel bearing; it cannot be repacked. If the bearing is damaged or noisy, it must be replaced.
    3. Press a new bearing race into the steering knuckle using a bearing driver of the correct size.
    4. Place a new bearing inner race on the hub bearing.
    5. Insert the side lip of a new oil seal into the seal installer and drive the oil seal into the steering knuckle.
    6. Apply multi-purpose grease to the oil seal lip.
    7. Apply sealer to the brake splash shield and install the shield.
    8. Use a hub installer to press the hub into the steering knuckle.
    9. Install a new snapring into the hub.
    10. Using a seal installer of the correct size, install a new outer oil seal into the steering knuckle.
    11. Apply multi-purpose grease to the seal surfaces which will contact the driveshaft.
    12. Support the knuckle and drive in a new dust deflector.
    13. Install the ball joint into the knuckle and tighten the nut to 105 ft. lbs. (142). Install NEW cotter pin.
    14. Temporarily install the hub assembly to the lower control arm and fit the driveaxle into the hub.
    15. Install the knuckle to strut bolts, then attach the tie rod end to the knuckle.
    16. Tighten the strut bracket nuts to 203 ft. lbs. (275 Nm) and tighten the tie rod end nut to 36 ft. lbs. (49 Nm). Install the NEW cotter pin.
    17. Connect the ball joint to the lower control arm and tighten the nuts to 105 ft. lbs. (142 Nm).
    18. Install the brake disc.
    19. Attach the brake caliper to the knuckle and tighten the bolts to 65 ft. lbs. (88 Nm).
    20. Install the center nut and washer on the drive axle.
    21. Install the ABS speed sensor if so equipped. Install the wheel
    22. Lower the car to the ground.
    23. Tighten the wheel nuts to 76 ft. lbs. (103 Nm). Tighten the hub nut while depressing the brake pedal to 137 ft. lbs. (186 Nm) on 1988-91 models and 152 ft. lbs. (206 Nm) on 1992-97 models. Install the cap and cotter pin.
    24. Remove the protective cover from the CV boot. Check front wheel alignment

Posted on Apr 25, 2009

  • 18 Answers

SOURCE: wheel bearing replacement left front

Diagnosing the bearings can be tricky depending on severity of wear. Typically - drone noise at highway speeds, squeeling, clicking or grinding noises at low speeds that reduce during braking, or pull off the wheel and brake assembly and check the bearing for slack or smoothness of rotation by hand. While doing this, check the brake assembly thoroughly - generally a more likely culprit of wheel noise.

Wheel bearing replacement is not for the novice backyard mech. - you will need pullers, press, etc. If you can get a rebuilt assembly - much easier.

Posted on May 08, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

How To Replace Front Wheel Hub Bearing 2000-05 Buick Lesabre 1AAuto.com


How To Replace Front Wheel Hub Bearing 2000-05 Buick Lesabre 1AAuto.com

on May 08, 2012 | 1997 Buick LeSabre

1 Answer

What other parts need to be replaced when replacing front wheel bearings on a 2006 Toyota Corolla?


depends on , doing it all or buying new hubs.... choices...
there are 2 ways to do this,, mach, puts the bearing in
or you just buy preloaded hubs.

you know, the online dealer pages for parts show the whole set of parts. all you do is look. ( no FSM> no alldata.com gander)
CE,LE,S or XRS
http://www.trademotion.com/parts/2006/Toyota/Corolla/CE?siteid=214001&vehicleid=187538&diagram=F800240&diagramCallOut=1


http://www.justanswer.com/toyota/0cje7-replace-right-front-wheel-bearing.html

rockauto shows diffr.parts for differ engines.
here is the 1.8L
i hate AZ but the photos clearly shows the bearing is presealed.
it must be pressed in.
http://www.autozone.com/autozone/parts/_/N-5yc1s?itemIdentifier=831176


preloaded, with or with out ABS./
out , search for ABS if you have it.

http://www.ebay.com/itm/Wheel-Hub-Front-Febest-0182-ZZE150MF-/261376385454?pt=Motors_Car_Truck_Parts_Accessories&fits=Make%3AToyota'Model%3ACorolla'Year%3A2006&hash=item3cdb3f21ae&vxp=mtr

Jan 19, 2014 | 2006 Toyota Corolla

2 Answers

I have a 2004 corolla that has a humming noise in the front when turning to the right.replaced the right front wheel bearing and noise still there.any ideas?


It's most likely the left wheel bearing that's causing the noise, when turning to the right the weight of the car shifts to the left placing more load on the left wheel bearing and takes load off the right bearing.

Aug 23, 2011 | 2004 Toyota Corolla

1 Answer

1990 toyota corolla - knocking (clattering) when turning to the left - sounds like coming from wheel, but then it sounds like it coming from middle of car -


check your cv axles, then check your wheel bearings on both axles by lifting car and shaking you tire left to right, up and down. if there is free play you need to replace front wheel bearings

Feb 19, 2010 | 1990 Toyota Corolla

1 Answer

Change the front wheel bearings toyota corolla 1992


front wheel bearings on this vehicle are part of a hub assy. you will have to completely remove the steering knuckle, press out the old bearing hub and rear seal and press in the new one.

Aug 03, 2009 | 1993 Toyota Corolla

1 Answer

Wheel bearing replacement left front wheel Hello Everyone, I may need to replace the wheel bearing on my right front wheel of my Corolla wagon. How can I know for sure? And how can I find out how to do...


Diagnosing the bearings can be tricky depending on severity of wear. Typically - drone noise at highway speeds, squeeling, clicking or grinding noises at low speeds that reduce during braking, or pull off the wheel and brake assembly and check the bearing for slack or smoothness of rotation by hand. While doing this, check the brake assembly thoroughly - generally a more likely culprit of wheel noise.

Wheel bearing replacement is not for the novice backyard mech. - you will need pullers, press, etc. If you can get a rebuilt assembly - much easier.

Apr 23, 2009 | 1996 Toyota Corolla

2 Answers

Toyota corolla


Remove wheel, brake cliper, cliper mounting bracket, brake pads and rotor.
Remove tie rod end and strut from spindle,
Remove large drive axle nut from center of hub by removing cotter pin and nut cover
Remove the ball joints 2 nuts and 1 bolt
Pull assy. lose from drive axle.
Take complete Hub assy with new bearing to an automotive machine shop and have them disassemble hub and replace bearing.
Reverse steps to reinstall

Jun 30, 2008 | 1994 Toyota Corolla

1 Answer

Wheel bearing


HI, For replace the front wheel bearing. on a toyota corolla 03
You need a hydrualic bench.
Because they goin pressed.
I recomend go to a repair shop, is not easy.
It's take about 2 hour to do. with the right tools.

Jun 28, 2008 | 2003 Toyota Corolla

Not finding what you are looking for?
2006 Toyota Corolla Logo

291 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

63291 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...