Question about 1999 Jeep Cherokee

1 Answer

1999 Cherokee Laredo-v8

Trying to remove starter. I have unbolted it but it looks like the exhaust system and the suspension system is in the way of getting it out. Is there any easy way to completely remove the starter from the car?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 475 Answers

There should be a way to take it out. You have to turn it in different positions and try to remove it.

Posted on Nov 10, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove starter on a 2006 4.7 cylander jeep commander


Disconnect battery.
Unbolt starter, move it down a bit.
Now unbolt wires (two of them).
Now wiggle starter around and get it out. On 99-04 grand cherokee the front wheels need to be on ground (or on a ramp) or the drooping suspension gets in the way.

Jul 01, 2014 | 2006 Jeep Commander

1 Answer

How do I remove the y-pipe once I have unbolted it from the heads on a 2004 Jeep Grand Cherokee, 4.7L V8?


04 GC.
the fSM , is free. see it here,
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

click exhaust.
click page.10
bingo, we love jeeps, and we have vast free documents, almost as good as honda's.
Sig: I must ask questions first, I'm blind, and my tools can't reach, dig?

Jun 22, 2014 | 2004 Jeep Grand Cherokee

1 Answer

Need to change the starter on a 2008 jeep grand cherokee limited with a v8 hemi. Found the starter but not sure how to get it out. Do I need to remove the exhaust or drive shaft? Thanks for your help.


Same issue. 2008 Grand with Hemi. loos like the Driveshaft has to come out but I still do not know if there is enough Wire length to get the wires off with the starter unbolted

Dec 09, 2010 | 2006 Jeep Grand Cherokee

1 Answer

Trying to change a 1998 Isuzu Rodeo v6 2WD starter and I'm looking for step by step instructions. Help?


1. Detach the cable from the negative terminal of the battery.
2. Raise the vehicle and support it securely on jack stands.
3. If you can reach them, disconnect the battery cable and solenoid connector from the starter motor solenoid. On some engines the terminals are difficult to reach while the starter is installed; it's actually easier to unbolt the starter, pull it out to point where you can reach and disconnect the cables.
4. Remove the starter motor bolts and detach the starter from the engine. Having socket swivels and extensions, along with angled wrenches, will make this job easier. Depending upon the year and engine type, the starter may be mounted above the transmission or below the intake manifold. On some models it may be necessary to remove the exhaust system to make room for the starter assembly to pass between the engine and chassis. Make sure the engine and exhaust system are cool before starting. I found that once you get the cables off, you have a better chance to remove the starter motor without removing the exhaust system. If you have to mess with the exhaust system, just loosen enough to allow clearance.
5. Install in the reverse order. If it was necessary to remove the starter to disconnect the cables, remember to maneuver the replacement starter in place, ensuring that you have the necessary access/clearance through the exhaust system, and reconnect the cables prior to bolting the starter in place.
6. Be patient. With the right tools and a little luck this shouldn't take more than an hour once you have the vehicle on jack stands and the engine has cool. It

Nov 16, 2010 | 1998 Isuzu Rodeo

2 Answers

Jeep 4.0 firing order


1999 Jeep Cherokee 4WD 4.0 liter L6 VIN "S"

71cf96f.gif

Hope this helps (remember rated this).

Aug 09, 2010 | 1998 Jeep Cherokee

1 Answer

1999 Jeep Grand Cherokee V8 Laredo 4x4 - While driving the car will just shut off. I lose all power and have no steering capabilities. There is no warning of this occuring. After a moment or so I am able...


I am only having a guess here but check the earth ******** the starter, i had this happen to me a few weeks ago and lost all power in my vehicle, the earth strap had broken at the starter and was only just touching
hope this helps

Jul 03, 2010 | 1999 Jeep Grand Cherokee

1 Answer

I have a 2005 jeep grand cherokee with a 5.7L hemi engine and the starter is bad. I have unbolted the starter and disconected the battery cable but I cant get the starter out, there isnt enough room. How...


its a pain I know remove the front drive shaft u don't have to take the shaft out but unbolt it and move it out of the way or through the drivers side wheel well. Hope this helps

Aug 17, 2009 | 2005 Jeep Grand Cherokee

1 Answer

Trying to take fan cluth off 1999 jeep grand cherokee laredo.


Get yourself a service manual with step by step instructions and diagrams. A good place is www.promanuals.net. $20 bucks or so for a factory one.

Jun 29, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Rear Axel Seal Leaking, How do I pull the axel to repair?


You will need to remove the differential rear cover,drain fluid, remove wheel, brake drum, (rotor) . Unbolt center diff. pin, carefully remove (don't loose shims) push axle in remove lock keeper, then slide out axle, replace seal, put some grease on it, slide axle in reverse all to install.

May 22, 2009 | 1999 Jeep Grand Cherokee

2 Answers

1999 Cherokee Laredo-v8


if its one click only then its probably the starter

Oct 11, 2008 | 1999 Jeep Cherokee

Not finding what you are looking for?
1999 Jeep Cherokee Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6876 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...