Question about 1998 Ford Explorer

1 Answer

2 problems transmission and windshield washer

98 ford exlporer sport 4.0 4wd .. tranny has e vin code. Torque converter clutch will not engage after warm up, works while warming up code p0741...

2ns Windshield washer in front will not work back works good since there is only one pump I assume it is reversed by a relay which is not listed in my owners manual any Ideas???

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 24 Answers

  The Po741 sounds like a leak at the seal to the convertor clutch. Need R&R to inspect. The fact the warm fluid makes it happen is a clue. The front washer has a seperate fuse and switch. If the fuse is good try switch in different wiper modes while pressing real hard. If it works the multi function switch needs replacement.

Posted on Nov 13, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is my 1998 Ford Windstar 98 reading DTC P0743?


#1) Low or dirty transmission fluid #2) Wire/circuit issue shorted to power or ground #3) Failed torque converter clutch (TCC) solenoid #4) Failed TCC assembly in the torque converter.....

Since Transmission has been rebuilt I would strongly suspect the TCC solenoid and/or its wiring...When transmission was rebuilt did the TCC get replaced? If so, due to being intermittent, Check the TCC plug (both female and male) for bent or dirty contacts...also insure you have close to zero ohms of resistance from negative battery post to transmission case...A poor ground will cause a problem and be at times...saailer

Apr 25, 2015 | 1998 Ford Windstar

2 Answers

What is the meaning of code 1744 in 2004 mercury sable


torque converter clutch stuck or not working properly

May 27, 2014 | 2004 Ford Explorer

2 Answers

P0741 code


P0741 MITSUBISHI - Torque Converter Clutch System Malfunctionxicon.jpghttp://engine-codes.com/p0741_mitsubishi.htmlForum CodePossible causes- Low transmission fluid level
- Dirty transmission fluid
- Faulty torque converter clutch solenoid valve
- Torque converter clutch solenoid valve harness or connectors
- Torque converter clutch solenoid valve circuit is open or shorted
- Transmission internal mechanical problem

Jun 25, 2012 | 2002 Mitsubishi Montero Sport

3 Answers

My Ford Focus 2006 4 cyc has an engine code PO741 on my OB2. What does that mean?


P0741 Torque convertor clutch circuit failure,it is located in the transmission valvle body, it is attatch to the valve body you can remove it seperately as long as your going to own the Ford focus you might as well get use to replacing these all the time,very common transmission issue with todays car. By the way it is sensitive to worn transmission fluid,when you dont service often these are suspectable to failure.

Apr 22, 2011 | Ford Focus Cars & Trucks

1 Answer

I am putting a 99 ford explorer tranny in a 98 explorer sport with the 4.0 sohc engine. the bolts match perfect and the torque converter from the 99 tranny lines up perfect with the fly wheel. when I go to...


The torque converter is not all the way in the transmission. Pull the transmission back out(unfortunately) and you will need to shake and wiggle while lightly pushing the torque converter into the transmission. Once it goes over the splines for the pump, you will know and the space between it and the transmission housing will be minimal.

May 13, 2010 | 1998 Ford Explorer

2 Answers

93 Chevy Pick-up,my son put washers between the torque converter and flywheel so the starter would engage. Driving down the road the trans locked up and killed the engine. He tried starting it again the...


theres a good chance that it broke the main shaft in the tranny from to much pressure forcing it back, be honest i would look for a good reman tranny and if your having problems with the starter to close to the torque converter they make shims for the starter to avoid that problem.

Nov 18, 2009 | 1993 Chevrolet K1500

1 Answer

02 SPORT TRAC JOLTS AT A FULL STOP


try changing your tranny fluid and in the torque converter. if that does not help check torque converter and clutch plates

Jun 30, 2009 | 2008 Ford Explorer Sport Trac

3 Answers

P0740


torque converter lock-up solenoids are at the top of the transmission on the OUTSIDE. The two came off with three bolts and the screens on mine were clogged with "lint".

Apr 11, 2009 | 1999 Acura CL

Not finding what you are looking for?
1998 Ford Explorer Logo

431 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...