Question about 1999 Pontiac Grand Am GT

1 Answer

Serpentine belt i need the diagram of how a serpentine belt goes on a 1999 pontiac grand am

Posted by on

  • Anonymous Jan 13, 2009

    belt diagram

  • Anonymous Mar 27, 2014

    it is squeaking

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

When you open the hood there is a diagram on a sticker that shows exactly how to do this. Should be on the front lip or the side of the engine compartment. You have to make sure you get it lined back up right and remember to check it once the engine has been started and make sure it running on all the pulleys correctly.

Here is a good diagram that should be able to help in case your sticker was damaged or removed. Good luck!

http://www.2carpros.com/car_repair_information/tec_info/1999/pontiac/grand_am/1999_pontiac_grand%20am_drive_belt_routing_diagram.htm

Posted on Nov 11, 2008

4 Suggested Answers

motor1258
  • 6674 Answers

SOURCE: serpentine belt replacement

Try this link, scroll down to your engine, click on picture to expand.

http://www.autozone.com/addVehicleId,2640503/initialAction,repairGuide/shopping/repairGuide.htm?pageId=0900c152800a326c

Posted on Jan 01, 2009

  • 6 Answers

SOURCE: serpentine belt diagram?

Should be a diagram sticker in the engine compartment, either under the hood or around the top of the radiator.

Posted on Mar 24, 2009

MEGA_MUZIK
  • 54 Answers

SOURCE: looking for a routing diagram of the serpentine

contact you rlocal advance auto parts, they can give you a free printout for you diagram.


if my info has been helpful, please remember to leave good review. you can contact me at mega_muzik@yahoo.com

Posted on Oct 27, 2009

cda2z
  • 120 Answers

SOURCE: belt routing diagram 1999 pontiac grand an gt v6

i belive this is the same as a 96 ? which has an auto tensioner towards bottom of engine towards rear of engine

Posted on Jul 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 grand prix GTP belt diagram


Hello
If you go to this LINK you will find a DAYCO Serpentine Belt Routing guide, just look up your car and the diagrams are at the end by number. This is a large pdf file so please alow time for it to download.

Dec 14, 2011 | 1999 Pontiac Grand Prix

1 Answer

(1999 pontiac grand prix 3100 v6) how do I remove and replace my serpentine belt successfully?


Instructions Things You'll Need
  • 3/8-inch drive breaker bar
  • Metric socket kit
  • New serpentine belt
    • 1

      Park the Pontiac in a safe work area and open the hood.

    • 2

      Inspect the top of the black plastic cover that surrounds the fan for the serpentine belt routing diagram. This diagram has the instructions for installing the new serpentine belt around the accessory pulleys.

    • 3

      Inspect the front of the engine and locate the automatic belt tensioner. The tensioner on the 1999 Pontiac model vehicles is located between the alternator and the crankshaft pulley. The tensioner has a pulley on one end with a bolt head in the center of the pulley. Use the bolt head to rotate the tensioner.

    • 4

      Turn the tensioner counterclockwise with the breaker bar and a metric socket. Pull the belt out from under the tensioner pulley with your other hand. Then, slowly let the tensioner retract until it stops.

    • 5

      Pull the belt out of the other remaining pulleys. Then, pull the belt out of the engine bay and lay it on the ground.

    • 6

      Route the new belt around the crankshaft pulley. Then, route the new belt around the other remaining pullleys by using the serpentine belt routing diagram for instructions.

    • 7

      Rotate the tensioner pulley counterclockwise with the breaker bar and socket. Then, slide the new belt under the tensioner pulley. Slowly let the tensioner retract until it stops. The tensioner pulls all of the slack out of the belt and brings the new belt to the proper tension. Remove the breaker bar and socket from the tensioner pulley.

    • 8

      Inspect the new belt to ensure that it is seated inside of all the accessory pulleys as directed by the diagram. Then, crank the engine and allow it to run for about 15 seconds. Turn the engine off. Inspect the belt again once more to ensure that
      the belt is still around each pulley. Close the hood.



May 22, 2011 | 1999 Pontiac Grand Prix

1 Answer

Diagram on how to replace the serpentine belt in a 1999 grand am


Heres a diagram, useing a rachet release tension by pulling tensioner up, hold and remove belt,you can release tension after removing belt from one pulley then install the belt leaving one belt off one pulley then release tension to finish the install, hope this is helpful, good luck.f00ecfa.gif

Oct 04, 2010 | 1999 Pontiac Grand Am GT

1 Answer

Belt routing diagram 1999 pontiac grand an gt v6


i belive this is the same as a 96 ? which has an auto tensioner towards bottom of engine towards rear of engine

Jul 16, 2010 | 1999 Pontiac Grand Am GT

1 Answer

Pontiac grand am 99 belt diagram


autozone will print on for you for free

May 07, 2010 | 1999 Pontiac Grand Prix

1 Answer

Looking for a routing diagram of the serpentine belt on a 1999 pontiac grand am gt 3.4 engine


contact you rlocal advance auto parts, they can give you a free printout for you diagram.


if my info has been helpful, please remember to leave good review. you can contact me at mega_muzik@yahoo.com

Oct 26, 2009 | 1999 Pontiac Grand Am GT

1 Answer

Diagram for surpentine belt installation 1999 grand prix


My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.
I have only been a free contributor to this site for the past 4-months.

I do not know if you still need this information, but I am going ahead and answering it anyway.

CLICK
on the following LINK. It has the Belt Diagrams you will need.

The standard rule to removal the Serpentine Belt:
1. Find the Tensioner(s). (See Diagrams on Link)
2. Rotate/Move the Tensioner away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.

3. Remove the loosened belt off one of the other more easily accessed Pulleys.

If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1999/make/pontiac/model/grand_prix/1999_pontiac_grand_prix_drive_belt_routing_diagram.htm

May 03, 2009 | 1999 Pontiac Grand Am GT

1 Answer

Serpentine belt diagram for


Usually and on most cars there's a belt diagram on the inside of the engine compartment near the radiator housing

Apr 04, 2009 | 1994 Pontiac Grand Prix

2 Answers

Need to replace serpentine belt for 1998 bonneville se


Use a break over to unload spring tensioner and pull old belt off. Look at belt diagram and reinstall new belt pull back tensioner and install.

Dec 23, 2008 | 1999 Pontiac Grand Am GT

Not finding what you are looking for?
1999 Pontiac Grand Am GT Logo

947 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...