Question about 1997 Toyota Camry

1 Answer

Need Timing Marks

Replacing a timing belt need marks ASAP before 9 this morning. Its a 6 cylinder 3.0

Posted by on

  • Colin Stickland
    Colin Stickland May 11, 2010

    take it you done it then??

  • Anonymous Mar 29, 2014

    I NEED THE INSTRUCTIONS TO PROPERLY SET THE TIMING MARKS AND MAKE SURE THE MOTOR IS SET PROPERLY

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 81 Answers

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the timing belt on a 1994 mazda 929 3.0 dohc 24 valve engine


Choose:

1994 Mazda MPV timing belt replacement, 6 cylinder DOHC ...

? 3:46
https://www.youtube.com/watch?v=sD2G-NzycvU
Aug 11, 2011 - Uploaded by rsarp
1994 Mazda MPV timing belt replacement, 6 cylinder DOHC 3.0... engine so the valves would not be bent ...

How to replace the timing belt on a 1994 mazda 929 3.0 ...

www.fixya.com/.../t25991928-replace_timing_belt_1994_mazda_929_3...
4 hours ago - how to replace the timing belt on a 1994 mazda 929 3.0 dohc 24 valve... I have a 2000 Mazda 626 4cyl 2.0 liter DOHC engine replacing the timing belt, what ... 2004 6s, 3l. where is the canister purge valve solenoid located?

Where are the timing marks on a 1994 mazda 929 3.0l - Fixya

www.fixya.com/cars/t25991952-timing_marks_1994_mazda_929_3_0l
4 hours ago - where are the timing marks on a 1994 mazda 929 3.0l - Mazda Cars ...1994 Mazda E2000 Cam Timing Mark Positions to Replace Timing Belt ... on a 1994mazda v6 dohc 24 valve engine How to align the timing mark on the ...

Mazda Timing Belt Replacement



Dec 03, 2015 | Mazda Cars & Trucks

2 Answers

2004 kia rio timing belt replacement procedure


from autozone.com

Removal & Installation

1.5L, 1.6L (VIN 5) & 1.8L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Remove the accessory drive belts.
  4. Remove the alternator.
  5. Remove the water pump and crankshaft pulleys.
  6. Remove the timing belt guide plate.
  7. Remove the upper and lower timing belt covers.
  8. Position the crankshaft so that the timing mark is aligned with the timing mark on the engine.
  9. Verify that the I and E mark on the camshaft pulley align with the mark on the cylinder head.
    NOTE Do not move the crankshaft or camshaft once the timing marks have been correctly positioned.
  10. If the timing belt is to be reused, mark the direction of rotation on the timing belt.
  11. Remove the timing belt tensioner pulley.
  12. Remove the timing belt.

25f366d.jpg

b46eac9.jpg

503792b.jpg
To install:
  1. Install the timing belt tensioner pulley, move the tensioner to its furthest point and tighten the lockbolt.
  2. Install the timing belt onto the pulleys, as follows, crankshaft pulley first, then the idler pulley, exhaust camshaft pulley, intake camshaft pulley, and the tensioner pulley.
  3. Loosen the tensioner pulley and allow the tensioner spring to apply tension on the belt, then tighten the lockbolt to 28-38 ft. lbs. (38-51 Nm).
  4. Rotate the crankshaft clockwise 2 turns and be sure all marks are still correctly aligned.
  5. Install the remaining components in the revere order of the removal noting the following torque specifications:

    Crankshaft pulley: 9-13 ft. lbs. (12-17 Nm) Water pump pulley: 9-13 ft. lbs. (12-17 Nm)
  6. Connect the negative battery cable.

1.6L (VIN 3) & 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    Negative battery cable Engine cover Right-hand front wheel Right-hand wheel well side cover Accessory drive belts Water pump pulley Timing belt upper cover
  3. Turn the crankshaft pulley so cylinder No. 1 is at Top Dead Center (TDC). Align the pulley groove with the timing mark T of the timing belt cover.
  4. Remove or disconnect the following:
    NOTE If the timing belt is to be reused, mark the belt to indicate its turning direction.


    Crankshaft pulley Crankshaft flange Lower timing belt cover Timing belt tensioner Timing belt

To install:
  1. Align the timing marks of the camshaft and crankshaft sprockets to ensure the No. 1 cylinder is at TDC.
  2. Temporarily install the timing belt tensioner.
  3. Install the timing belt over the crankshaft sprocket, then inside the idler pulley, over the camshaft sprocket and then inside the timing belt tensioner.
  4. Apply tension to the timing belt by turning the tensioner in the clockwise direction so there is no slack in the belt on the tension side.
  5. Tighten the tensioner mounting bolts to 20 ft. lbs. (27 Nm).
  6. Check the timing belt tension as follows:
    1. 1.6L (VIN 3) engine: Push the tension side of the belt in horizontally with a moderate force, the timing belt cog end is approximately 1 / 2 of the tensioner mounting bolt head radius away from the bolt head center.
    2. 2.0L engine: Push the tension side of the belt in horizontally with a moderate force, the timing belt cog end sags approximately 0.16-0.24 inches (4-6 mm).

  7. Turn the crankshaft two turns in the clockwise direction and realign the crankshaft sprocket and camshaft sprocket timing marks.
  8. Install or connect the following:

    Lower timing belt cover. Tighten bolts to 6-7 ft. lbs. (8-10 Nm). Crankshaft flange Crankshaft pulley. Tighten bolt to 101-109 ft. lbs. (138-147 Nm) for 1.6L (VIN 3) engine and 123-130 ft. lbs. (168-177 Nm) for 2.0L engine. Upper timing belt cover. Tighten bolts to 6-7 ft. lbs. (8-10 Nm). Water pump pulley Accessory drive belts Right-hand wheel well side cover Right-hand front wheel Engine cover Negative battery cable

Sep 06, 2010 | 2004 Kia Rio

1 Answer

How do set the timing on hyundai excel 1998


Hi,


It seems you are encountering problems trying to set the timing marks in your elantra,not to worry,simply follow the stepwise solution below;
Ensure timing marks aligned [6] & [7] .

STEP 1. Fit timing belt in anti-clockwise direction, starting at crankshaft sprocket. Ensure belt is taut between sprockets.

STEP 2. Slacken tensioner pulley bolt [8].Push tensioner pulley firmly against timing belt to tension belt.



STEP 3. Tighten tensioner pulley bolt [8] . Tightening torque: 43-55 Nm.


STEP 4. Except Matrix: Turn crankshaft one turn clockwise.



STEP 5. Matrix: Turn crankshaft two turns clockwise.


STEP 6. Ensure timing marks aligned [6] .


STEP 7. Apply a load of 2 kg to belt at .Belt should deflect 4-6 mm. If not Adjust position of tensioner pulley.



STEP 8. Install components in reverse order of removal.


STEP 9. Tighten crankshaft pulley bolt [2] . Tightening torque: 170-180 Nm
(7) is timing mark on cam,pin mark to top,hole in spoke below pin mark lines up with mark on head (6) is crank timing mark,pin mark on crank lines up with markS on block.





Good luck.

Aug 20, 2010 | Hyundai Excel Cars & Trucks

2 Answers

Looking for timing mark's for a 1997 camry with a 2.2 4cyl motor?


Hi,


You find the timing marks on the picture below.

moz-screenshot-2.pngaab8238.jpg



Removal
Remove auxiliary 1. drive belts.
2. Support engine.
Remove:
Engine mounting and bracket.
Timing belt upper cover [1].
3.
4. Turn crankshaft clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
Remove:
Crankshaft pulley bolt [4].
Crankshaft pulley [5]. Use tool No.09213-60017.
5.
6. Ensure timing marks aligned [2] & [3].
7. Slacken tensioner bolt [6]. Move tensioner away from belt and lightly tighten bolt.
Remove:
Timing belt lower cover [7].
Crankshaft sprocket guide washer [9].
Timing belt.
Tensioner pulley.

Installation
Installation
1. Check tensioner pulley for smooth operation.
2. Check free length of tensioner spring is 46,0 mm [8]. Replace spring if necessary.
3. Fit tensioner and spring. Ensure spring is connected correctly.
4. tighten bolt [6].
5. Ensure timing marks aligned [2] & [3].
6. Fit timing belt. Ensure belt is taut between sprockets.
Install:
Crankshaft sprocket guide washer [9].
Timing belt lower cover [7].
Crankshaft pulley [5].
7.
8. Slacken tensioner bolt 1/2 turn [6].
9. Turn crankshaft two turns clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
Turn crankshaft slowly 1 7/8 turns clockwise until crankshaft pulley timing mark [3] aligned with 45° BTDC mark [10] on
timing belt lower cover [7].
10.
11. Tighten tensioner bolt [6]. Tightening torque: 42 Nm.
12. Install components in reverse order of removal.
13. Tighten crankshaft pulley bolt [4]. Tightening torque: 108 Nm.
Manufacturer: Toyota

Jun 25, 2010 | 1997 Toyota Camry

1 Answer

Timing marks setting Hyundai Lantra


Installation
Ensure timing marks aligned [6] & [7] . 1. Fit timing belt in anti-clockwise direction, starting at crankshaft sprocket. Ensure belt is taut between sprockets. 2. Slacken tensioner pulley bolt [8] . Push tensioner pulley firmly against timing belt to tension belt. 3. Tighten tensioner pulley bolt [8] . Tightening torque: 43-55 Nm. 4. Except Matrix: Turn crankshaft one turn clockwise. 5. Matrix: Turn crankshaft two turns clockwise. 6. Ensure timing marks aligned [6] . 7. Apply a load of 2 kg to belt at . Belt should deflect 4-6 mm. If not: Adjust position of tensioner pulley. 8. Install components in reverse order of removal. 9. Tighten crankshaft pulley bolt [2] . Tightening torque: 170-180 Nm

7 is timing mark on cam,pin mark to top,hole in spoke below pin mark lines up with mark on head
6 is crank timing mark,pin mark on crank lines up with mark on block
NOTE this mark is just before top


Mar 21, 2010 | Hyundai Motor 1996 Elantra

2 Answers

Hi need to know what timing marks to use when replacing cams


The timing marks to use are spot-drilled on the faces of the timing gears.
The timing marks on the camshaft gears must align side-by-side, and as closest as possible on the Toyota,Camry 2.2 engine.

Dec 20, 2009 | 1995 Toyota Camry

1 Answer

I need a new timming belt on a 01 kia sephia how do i change it


Hi there,

Below are the procedures to remove the timing belt...

1. Disconnect negative battery cable.

fd440e5.jpg
2. Loosen power steering lock bolts and nuts accordingly and remove tension from power steering (P/S) and/or air conditioning (A/C) compressor drive belt. 3. Remove P/S and/or A/C drive belt.

1d207cf.jpg

4. Loosen generator mounting bolts and adjusting bolt. 5. Remove generator bolts.


077a275.jpg

6. Remove water pump pulley.

2bc0452.jpg


7. Remove crankshaft pulley and timing belt guide plate.



8619b52.jpg


8. Remove upper and lower timing belt covers.


c250533.jpg


9. Turn crankshaft so that timing mark on timing belt pulley is aligned with timing mark on engine.


213d3a1.jpg




10. Check that "I" mark on intake camshaft pulley is aligned with mark on cylinder head cover and "E" mark on exhaust camshaft pulley is aligned with mark on cylinder head cover.


Do not move camshaft or crankshaft once timing marks have been correctly positioned.



a3188ba.jpg



11. Loosen tensioner pulley lock bolt.
12. Protect timing belt with a rag.
13. Remove tensioner pulley.


12101a7.jpg

14. Remove timing belt.



Regards,
Jeep Brainy

Sep 20, 2009 | 2001 Kia Sephia

1 Answer

I AM REPLACING THE TIMING BELT ON MY 1999 DAEWOO WITH 1.5 LITRE ENGINE AND NEED TO KNOW THE TIMING SPECS SO I CAN SET THE TIMING ON THE CRANKSHAFT....ALSO I NEED TO KNOW THE T.D.C. ON THE #1 CYLINDER FOR...


single cam
cam at 12 o clock
crank at 6 o clock
marks in rear timming cover

twin cam
cams marks face each other 3 & 9 o clock
crank at about 6 o clock mark in cover
all marks are visible on gears and covers

May 15, 2009 | 1999 Daewoo Leganza

1 Answer

Timing for tropper 6cly and 4 camshafts and 24 valves model 2000


Timing Belt
Removal
1. Disconnect battery ground cable.
2. Remove air cleaner assembly.
3. Remove radiator upper fan shroud from radiator.
4. Move drive belt tensioner to loose side using wrench
then remove drive belt.
850RW001
Legend
(1) Crankshaft Pulley
(2) Cooling Fan Pulley
(3) Tensioner
(4) Generator
(5) Air Conditioner Compressor
(6) Power Steering Oil Pump
(7) Drive Belt
5. Remove cooling fan assembly four nuts, then the
cooling fan assembly.
6. Remove cooling fan drive pulley assembly.
7. Remove idle pulley assembly.
8. Remove serpentine belt tensioner assembly.
9. Remove power steering pump assembly.
10.Remove crankshaft pulley assembly using
5–8840–0133–0 crankshaft holder, hold crankshaft
pulley remove center bolt, then the pulley.
11. Remove right side timing belt cover then left side
timing belt cover.
12. Remove lower timing belt cover
13. Remove pusher.
CAUTION: The pusher prevents air from entering
the oil chamber. Its rod must always be facing
upward.
014RW011
Legend
(1) Up Side
(2) Down Side
(3) Direction For Installation
(4) Locking Pin
14. Remove timing belt.
CAUTION:
1. Do not bend or twist the belt, otherwise its core
could be damaged. The belt should not be bent at
a radius less than 30 mm.
2. Do not allow oil or other chemical substances to
come in contact with the belt. They will shorten
the life.
3. Do not attempt to pry or stretch the belt with a
screw driver or any other tool during installation.
4. Store timing belt in a cool and dark place. Never
expose the belt direct sunlight or heat.
6A–30 ENGINE MECHANICAL
Installation
NOTE: For correct belt installation, the letter on the belt
must be able to be read as viewed from the front of the
vehicle.
014RY00042
Legend
(1) Crankshaft Timing Pulley
(2) RH Bank Camshaft Drive Gear Pulley
(3) Water Pump Pulley
(4) Idle Pulley
(5) LH Bank Camshaft Drive Gear Pulley
(6) Tension Pulley
014RY00043
Legend
(7) Alignment Mark on Oil Pump.
(8) Alignment Mark on Timing Belt
(9) Alignment Mark (notch) on Crankshaft Timing
Pulley.
(10) Alignment Mark (groove) on Crankshaft Timing
Pulley.
014RW006
Legend
(1) Timing Belt
(2) Engine Rotation Direction
(3) Cylinder Head Side
1. Install timing belt.
1. Align the mark (notch) of crankshaft timing pulley
(2) with mark on oil pump (1).
Align the mark (groove) on the crankshaft timing
pulley (3) with alignment mark (white dots line) on
the timing belt (4).
NOTE: When timing marks are aligned, No.2 piston will
be on Top Dead Center.
014RW003
Legend
(1) Alignment Mark on Oil Pump
(2) Groove on Crankshaft Timing Pulley
(3) Alignment Mark on Crankshaft Timing Pulley
(4) Alignment Mark on Timing Belt
ENGINE MECHANICAL 6A–31
2. Align the alignment mark on the RH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover RH (3).
3. Align the alignment mark (white line) on the timing
belt (1) with alignment mark on the RH bank
camshaft drive gear pulley (2) (on the left side as
viewed from the front of the vehicle) and put the
timing belt on the camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
014RW00004
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover RH.
4. Align the alignment mark on the LH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover LH (3).
5. Align the alignment mark (white line) on the timing
belt (1) with the alignment mark on the LH bank
camshaft drive gear pulley (2).
When aligning the timing marks, use a wrench to
turn the camshaft drive gear pulley, then set the
timing mark between timing belt and camshaft
drive gear pulley and put the timing belt on the
camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
NOTE: It is recommended for easy installation that the
belt be secured with a double clip or equivalent clip after
it is installed the timing belt to each pulley.
014RW00005
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover LH.
6. Install crankshaft pulley temporarily and tighten
center bolt by hand (do not use a wrench).
Turn the crankshaft pulley clockwise to give some
belt slack between the crankshaft timing pulley
and the RH bank camshaft drive gear pulley.
2. Install pusher and tighten bolt to the specified torque.
Torque : 25 N·m (2.5 Kg·m/18 lb ft)
1. Install the pusher while pushing the tension pulley
to the belt.
2. Pull out pin from the pusher.
NOTE: When reusing the pusher, press the pusher with
approximately 100Kg to retract the rod, and insert a pin
(1.4 mm piano wire).
014RW011

Mar 18, 2009 | 2000 Isuzu Trooper

2 Answers

I need instructions on replacing the timing belt


1. Remove the Alternator Belt.
2. Remove the Water Pump Pulley
3. Remove the Air Conditioner Belt and Power Steering Belt.
4. Remove the Crankshaft Pulley.
5. Remove the timing belt cover
6. Remove the timing belt tensioner pulley.
7. Remove the Timing Belt.
8. (If Replacing) Remove Idler Pulley.
Installation is reverse of removal. Keep a close eye on the timing marks on the cam sprockets to make sure you don't knock anything out of whack.

I would strongly recommend replacing the water pump while you are replacing the timing belt. (The water pump usually comes in the timing belt kit.) Otherwise you are going to have to do this all over again when your water pump goes out. Good Luck.

Nov 10, 2008 | 2004 Hyundai Tiburon

Not finding what you are looking for?
1997 Toyota Camry Logo

Related Topics:

162 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...