Question about 1997 Mitsubishi Galant

1 Answer

Crankshaft pulley when i start my galant it makes like a snapping sound,sometimes it does sometimes it doesn,t it comes from the cranksaft pulley,i wated it and the pulley seems to go in and out like an 1 inche or so,thats when i hear this sound,like clicking and like i said it doesn,t do it all the time after it warms up the pulley stays still. roger6632@yahoo.com

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 979 Answers

You will, very soon, need a crank pulley assembly; This one is on its last legs due to the rubber rotting out...accordianman

Posted on Dec 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 eldorado cadillac-One month ago, replaced water pump, smelled rubber burning & loss of antifreeze, mechanic noticed the cranksaft pulley and belt was destroyed & must replace. A second o


I'd have to see the car to say for sure.
Usually when a belt melts one of the pulleys locked up which would not have been the crank pulley.
A mechanic would check each pulley for movement.

Jan 28, 2013 | 2000 Cadillac Eldorado

1 Answer

There was a thumpiing noise in the engine, something popped and now it wont start.


either you have a snapped timing belt or snapped valve.
Do attempt to turn engine via crankshaft pulley bolt. if there is no turn then you have to remove the timing cover and see what is the timing belt condition,

Sep 02, 2012 | 2005 Honda Odyssey

1 Answer

How do I put on a front crank seal?


1. Disconnect battery and block drive wheel.
2.Remove cooling fan and fan shroud
3.Remove drive belt
4.Remove front crank shaft sensor
5.Hold down the crank pulley(strap wrench)
6.Use a breaker bar,front pulley nut is 22mm
Becareful at this area, when pulling out the pulley, If it is necessary for you to remove the front radiator. A crankshaft pulley remover should be used.
7.With the front pulley removed,The front crankseal can now be pulled out be careful NOT to nick the timing cover.
8.Clean the bore of old seal material
9.When you get the new seal ready for installation on the inner lip lubricate it with grease so it will not suffer a dry run.
10.Drive the seal in using a socket and hammer.
11.Inspect the crankshaft before installing. If the cranksaft has any deep grooves ,a press on sleeve will be required.
12.Lubricate the pulley and line up with the half moon dowel and reinstall.
13. Torque the Pulley to specifcation 29Ft-lbs 36Ft-lbs with an additional 60 degree turn
Reinstall in reverse order

Apr 25, 2011 | 1998 Nissan Pathfinder

2 Answers

Looking for timing mark's for a 1997 camry with a 2.2 4cyl motor?


Hi,


You find the timing marks on the picture below.

moz-screenshot-2.pngaab8238.jpg



Removal
Remove auxiliary 1. drive belts.
2. Support engine.
Remove:
Engine mounting and bracket.
Timing belt upper cover [1].
3.
4. Turn crankshaft clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
Remove:
Crankshaft pulley bolt [4].
Crankshaft pulley [5]. Use tool No.09213-60017.
5.
6. Ensure timing marks aligned [2] & [3].
7. Slacken tensioner bolt [6]. Move tensioner away from belt and lightly tighten bolt.
Remove:
Timing belt lower cover [7].
Crankshaft sprocket guide washer [9].
Timing belt.
Tensioner pulley.

Installation
Installation
1. Check tensioner pulley for smooth operation.
2. Check free length of tensioner spring is 46,0 mm [8]. Replace spring if necessary.
3. Fit tensioner and spring. Ensure spring is connected correctly.
4. tighten bolt [6].
5. Ensure timing marks aligned [2] & [3].
6. Fit timing belt. Ensure belt is taut between sprockets.
Install:
Crankshaft sprocket guide washer [9].
Timing belt lower cover [7].
Crankshaft pulley [5].
7.
8. Slacken tensioner bolt 1/2 turn [6].
9. Turn crankshaft two turns clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
Turn crankshaft slowly 1 7/8 turns clockwise until crankshaft pulley timing mark [3] aligned with 45° BTDC mark [10] on
timing belt lower cover [7].
10.
11. Tighten tensioner bolt [6]. Tightening torque: 42 Nm.
12. Install components in reverse order of removal.
13. Tighten crankshaft pulley bolt [4]. Tightening torque: 108 Nm.
Manufacturer: Toyota

Jun 25, 2010 | 1997 Toyota Camry

1 Answer

WHERE IS TE CRANKSAFT LOCATED AT ? OW DO I ET TO


If you look at the harmonic balancer through the fender well.It will be bolted at the 2 o clock position if it were a clock.

Apr 27, 2010 | 1999 Mitsubishi Galant

1 Answer

Change timing belt galant 04 mivec 2.4


49885ff.gif
Timing belt “B” (balancer belt) and related components—2004–2005 Galant and 2004–2005 Lancer 2.4L engine


  1. Disconnect the negative battery cable. Remove the engine under cover.
  2. Remove the crankshaft damper pulley.
  3. Disconnect the control wiring harness connector, battery wiring harness connector and connector bracket to engine mounting insulator.
  4. Remove the harness bracket. Remove the upper timing belt cover. Remove the water pump pulley. Remove the idler pulley.
  5. Remove the auto tensioner. Remove the lower timing belt cover.
  6. Turn the crankshaft clockwise and align each timing mark to set the number one piston to TDC of its compression stroke.
  7. Remove the timing belt under cover rubber plug and then install special tool MD998738. Screw the special tool until it contacts the timing belt tensioner arm.

    NOTE The special tool must be screwed in gradually at the rate of a 30 degree turn per second. If it is screwed in all at once, the timing belt tensioner adjuster rod will not easily retract and the tool may bend.

  8. Gradually screw in the special tool and then align the timing belt tensioner adjuster rod set hole “A” with the timing belt tensioner adjuster cylinder set hole “B”.
  9. Insert a wire or pin in the set holes to lock the assembly in place. After removing the special tool, loosen the timing belt tensioner pulley mounting bolts and remove the timing belt. If the belt is being reused be sure to mark the direction of rotation (clockwise) on the belt.
  10. Remove the timing belt tensioner pulley, tensioner arm and adjuster.
  11. Remove the timing belt idler pulley. Remove the timing belt lower cover bracket. Remove the crankshaft position sensor.
  12. Remove the crankshaft pulley center bolt and washer. Remove the drive sprocket. Remove the crankshaft angle sensing blade.
  13. Remove the balancer timing belt tensioner. Remove the timing belt “B” (balancer belt) from its mounting.


284eb62.gif
Timing belt tensioner adjuster rod set hole “A” and cylinder set hole “B”—2004–2005 Galant and 2004–2005 Lancer 2.4L engine

To install:


78b2d67.gif
Belt tension checking—2004–2005 Galant and 2004–2005 Lancer 2.4L engine


b8fcecc.gif
Cylinder block plug location—2004–2005 Galant and 2004–2005 Lancer 2.4L engine


bad1ef9.gif
Timing belt sprocket alignment—2002–2004–2005 Galant and 2004–2005 Lancer 2.4L engine

Feb 27, 2010 | 2004 Mitsubishi Galant

1 Answer

Unable to remove crankshaft pulley on 1998 Mitsubishi Galant 2.4L


crankshaft pulley nuts are very tight,some are 85-90 ft lbs.use a 1/2 inch drive breaker bar & socket.put auto trans in park manual trans in gear with emergency brake on.

Oct 18, 2009 | 1998 Mitsubishi Galant

2 Answers

When i start the car, making loud squeaking sounds


do not add oil to belts. remove belt and spin all pulleys (except crankshaft pulley) any pulley does not turn freely (except crankshaft pulley) is where you will find your problem

Jun 29, 2009 | 2000 Jeep Cherokee

2 Answers

2002 Mitsubishi galant


Remove the drive belts, crankshaft pulley, and timing covers. Align the timing marks on the camshaft and crankshaft and r+r the belt

May 15, 2008 | 2002 Mitsubishi Galant

Not finding what you are looking for?
1997 Mitsubishi Galant Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...