Question about 1999 Mercedes-Benz E-Class

1 Answer

E240 year 2000 fascia lights go out when headlamps switched on

Posted by on

  • whl_anil Dec 23, 2008

    my instrument claster and cd player screen gets dim when the head lamps are turned on qhy is this and does i cost allot to repair or isit a simple error? i have a 2006 e280 sport

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Check for a little guage (volume) which turn the interior lights on and off - make sure it is on maximum

Posted on Apr 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace driver side headlight 2003 nissan altima


To Remove:
  1. Ensure that the lighting switch is in the OFF position.
  2. Disconnect negative battery cable.
  3. Remove or disconnect the following:
  • Front Fascia
  • Headlamp mounting bolts.
  • Headlamp by sliding it foward.
  • Headlamp connectors.


tecnovative_52.gif
To Install:
  1. Install or connect the following.
  • Headlamp connectors.
  • Headlamp and mounting bolts.
  • Front fascia.
  • Negative battery cable.

Jan 14, 2011 | 2003 Nissan Altima

1 Answer

Need to replace the headlight assembly on front passenger side do i have to take off the bumper? for ponitac vibe 2003 also have dent on the area


Yes you do. This is the steps to do that to replace the entire headlight assembly:


Remove the front fascia.
  • Remove the front fascia extensions, if equipped.
  • Remove the front fender liners.
  • Remove the fog lamps.
  • Remove the bolts (4) from the front bumper fascia (3) at the fender.


506bafd.gif

Remove the bolts from the front bumper fascia at the fender



  • Remove the push-in retainers (2) from the bumper fascia using J38778.
  • Remove the fascia bolts (1) from the fascia.
  • Remove the fascia from the vehicle.
  • Remove the 3 bolts which secure the composite headlamp.


  • 7f1ec16.gif

    Remove the 3 bolts which secure the composite headlamp



    1. Remove the sidemarker bulb electrical connector.
    2. Remove the sidemarker bulb, if necessary.
    3. Remove the composite headlamp assembly from vehicle.

    To install:

    1. Install the sidemarker bulb to the composite headlamp, if removed.
    2. Connect the sidemarker bulb electrical connector.
    3. Secure the composite headlamp to the vehicle with the 3 bolts. Tighten the headlamp mounting bolts to 89 inch lbs. (10 Nm).
    4. Install the front fascia.
    5. Install the headlamp bulb to the composite headlamp, if removed.
    6. Fasten the headlamp bulb retainer clip.
    7. Install the socket to the headlamp bulb.
    8. Install the rubber cover to the composite headlamp.
    9. Aim the headlamps.
    10. Close the hood.

    Oct 12, 2010 | 2003 Pontiac Vibe

    1 Answer

    How to change head lights


    Hello and welcome. here is the headlight replacement instructions.

    Open the hood.



    Remove the fascia to tie bar push-in retainers (1).

  • Gently pull the top of the fascia assembly several inches away from the vehicle to release the radiator grille strap from the headlamp.
  • Place a piece of tape over the radiator grille strap to headlamp retaining clip to prevent scratching of the headlamp lens.
  • Remove the headlamp bolts (1, 2).



    Pull gently on the bottom outboard corner of the headlamp to disengage the lower rear headlamp retainer.

  • Remove the bulbs (2, 3, 4, 5) from the backside of the headlamp.
  • Remove the headlamp from the vehicle.

  • 2379f3f.gifd9c6d55.giffc562f4.gif2d89b70.gifa552625.gif

    Aug 30, 2010 | 2006 Chevrolet Equinox

    3 Answers

    How do i get to the head light on my 2008yukon denali with out pulling air filter box out and windshild washer out


    This is a rather difficult task to perform as the complete headlamp must be removed to do so. Here is what you will need to do to access the bulb. Feel free to contact me with any questions! Good luck.

  • Remove the 2 forward wheelhouse liner screws.
  • Remove the 2 washer container push pins.
  • Open the hood.
  • Remove the 6 upper fascia bolts right to the hood latch mechanism.
  • Remove the lower rear fascia bolt from the support bracket.
  • Loosen the 2 fascia to fender bolts from under the fascia.
  • Pull the outboard end of the front fascia straight outboard until it disengages from the fender attachment bracket.
  • Pull the fascia forward and downward to allow enough clearance to remove the headlamp assembly.
  • Loosen the lower outboard attachment bolts.
  • Remove the 2 upper headlamp bolts.
  • Grasp the headlamp at the upper inboard and lower outboard side and pull the headlamp forward to disengage the locating tab.
  • Pull the outboard side of the headlamp forward until the 2 locating pins disengage from the radiator support.
  • Disconnect the forward lamp harness connector.
  • Dec 07, 2009 | 2008 GMC Yukon Denali

    1 Answer

    How do you remove the air filter box on a 2001


    REMOVAL
    Release hood latch and open hood.
    Access Rubber Grommet
    Remove large rubber grommet (70 mm x 168 mm) from splash shield to gain access to fascia fasteners.
    Fastener Locations

    Remove fasteners attaching fascia to the front fender and splash shield, using access hole in splash shield.
    Remove Push In Fasteners
    Remove the push pins attaching the fascia to the upper radiator closure panel.
    Headlamp Jack screws

    Remove jackscrews attaching headlamp housing to crossmember and remove the lamp housing to access the lamp(s).
    Roll Fascia Forward

    Roll fascia forward to clear way for headlamp housing removal.
    Disconnect wire connector from back of lamp socket(s) and/or bulbs.
    Remove Headlamp Housing

    INSTALLATION
    CAUTION : Do not touch the glass of halogen bulbs with fingers or other possibly oily surface, reduced bulb life will result.

    Place headlamp housing into position.
    Connect wire connector to lamp socket(s)
    Verify headlamp and signal lamp operation.
    Install jackscrews to attach headlamp housing to crossmember.
    Align fascia to bumper reinforcement and install the top center push pins, to upper radiator closure panel.
    Align the two fascia studs to the fender vertical attachments, at the same time align the fascia groove on the horizontal flange with the fender drive pin. Push fascia rearward to engage the fasteners.
    Install nut on fascia stud through the splash shield access hole.
    Verify headlamp operation and alignment


    Nov 03, 2009 | 2001 Chrysler 300M

    1 Answer

    Wat tools use to change head light bulb in a chevy equinox


    You will need basic hand tools.

    Headlamp Bulb: Service and Repair
    HEADLAMP BULB REPLACEMENT (EQUINOX)
    REMOVAL PROCEDURE
    1. Open the hood.
    90a07c3.jpg 2. Remove the fascia to tie bar push-in retainers (1).
    888ce48.jpg 3. Gently pull the top of the fascia assembly several inches away from the vehicle to release the radiator grille strap from the headlamp.
    4. Place a piece of tape over the radiator grille strap to headlamp retaining clip to prevent scratching of the headlamp lens.
    25ee555.jpg 5. Remove the headlamp bolts (1, 2).
    054ce4f.jpg 6. Pull gently on the bottom outboard corner of the headlamp to disengage the lower rear headlamp retainer.
    7. Remove the headlamp from the vehicle.
    INSTALLATION PROCEDURE
    985fba5.jpg
    1. Position the headlamp into the headlamp opening.
    e3187c6.jpg 2. Push the headlamp back into position until the lower rear retainer is fully engaged.
    e5916af.jpg 3. NOTE: Refer to Fastener Notice.
    Install the headlamp bolts (1, 2)
    Tighten the headlamp bolts to 2.5 N.m (22 lb in).
    4. Remove the tape from the radiator grille strap retainer.
    efd9aad.jpg 5. Position the fascia assembly and engage the radiator grille strap retainer into the headlamp.
    5a4fd4a.jpg 6. Install the fascia to tie bar push-in retainers (1).
    7. Close the hood.
    8. Check and adjust the front headlamp aim after the headlamp has been reinstalled. Refer to Headlamp Aiming.

    Oct 04, 2009 | 2007 Chevrolet Equinox LS New Cars

    1 Answer

    Replacing headlight bulbs Altima2003


    Removal and Installation To Remove:
    1. Ensure that lighting switch is in the OFF position.
    2. Disconnect negative battery cable.
    3. Remove or disconnect the following:
      • Front fascia
      • Headlamp mounting bolts
      • Headlamp by sliding it forward
      • Headlamp connectors
    To Install:
    1. Install or connect the following:
      • Headlamp connectors
      • Headlamp and mounting bolts
        1. Torque to: 58 in. lbs. (6.5 Nm)
      • Front fascia
      • Negative battery cable
    71c495d.gif

    Oct 01, 2009 | 2003 Nissan Altima

    1 Answer

    How is cornering lamp changed in 2002 Buick Regal.



     
     
    Lighting
    Headlight Assembly
    Removal & Installation
    To Remove:

    Open the hood.
    Apply light pressure to the headlamp lens to hold the headlamp in place while disconnecting the retainers.
    Lift up the retainers to release and remove the retainers.
    Remove the headlamp mounting tabs from the slots in the upper fascia support and fender reinforcement.
    Disconnect the wiring harness from the headlamp assembly.
    Remove headlamp.
    Remove the rubber access cover from the appropriate bulb to be replaced.
    Rotate the headlamp bulb/socket counterclockwise to remove from the headlamp assembly.
    To Install:
    Connect the wiring harness to the headlamp.
    Install the headlamp bulb/socket to the headlamp assembly rotating the socket clockwise until fully seated.
    Install the rubber access cover.
    Position the headlamp mounting tabs to the slots in the upper fascia and fender reinforcement.
    Apply light pressure to the headlamp lens to hold the headlamp in place while installing the retainers.
    Align the headlamp assembly retainers and slide them over the headlamp mounting tabs.
    Close the hood.

     
    Top of Form 1
    Bottom of Form 1

    Mar 30, 2009 | 2002 Buick Regal

    1 Answer

    How do you replace headlamp bulbs on 1999 chrysler 300


    You half to remove the Headlamp housing to change it. Here is the instructions out of the factory manual.
    Tell me if this works for you?
    HEADLAMP HOUSING - CONCORDE/LHS/330M Headlamp lens fogging is a normal condition and does not require service unless excessive or continual. Moisture will vent from tubes or vents located on the back of the lamp.
    REMOVAL
    1. Release hood latch and open hood.
    2. Remove large rubber grommet (70 mm x 168 mm) from splash shield to gain access to fascia fasteners Access Rubber Grommet
    3. Remove fasteners attaching fascia to the front fender and splash shield, using access hole in splash shield Fastener Locations
    4. Remove the push pins attaching the fascia to the upper radiator closure panel Remove Push In Fasteners
    5. Remove jackscrews attaching headlamp housing to crossmember and remove the lamp housing to access the lamp(s) Headlamp Jackscrews
    6. Roll fascia forward to clear way for headlamp housing removal Roll Fascia Forward
    7. Disconnect wire connector from back of lamp socket(s) and/or bulbs.
    8. Remove headlamp housing Remove Headlamp Housing
    INSTALLATION CAUTION: Do not touch the glass of halogen bulbs with fingers or other possibly oily surface, reduced bulb life will result.
    1. Place headlamp housing into position.
    2. Connect wire connector to lamp socket(s) and/or bulbs.
    3. Verify headlamp and signal lamp operation.
    4. Install jackscrews to attach headlamp housing to crossmember.
    5. Align fascia to bumper reinforcement and install the top center push pins, to upper radiator closure panel.
    6. Align the two fascia studs to the fender vertical attachments, at the same time align the fascia groove on the horizontal flange with the fender drive pin. Push fascia rearward to engage the fasteners.
    7. Install nut on fascia stud through the splash shield access hole.
    8. Verify headlamp operation and alignment

    Mar 27, 2009 | 1999 Chrysler 300M

    1 Answer

    How to replace front turn light bulb on Caddy SRX 2004?


    1. Open the hood.
    2. Remove the push-pin retainers that secure the top of the upper fascia and grille assembly to the upper tie bar to allow the upper fascia and grille assembly to flex forward.
    3. Remove the bolt and the push-pin retainer that secures the top of the headlamp assembly to the upper tie bar.
      1. Gently pull the upper fascia and grille assembly forward only far enough to remove the bolt located at the bottom inboard side of the headlamp assembly.
      2. Pull the headlamp assembly straight out to disengage the snap-in retainer at the lower outboard back surface of the assembly. Turn the assembly so that the front inboard corner clears the front fascia.
      3. Pull the headlamp assembly out and away from the vehicle
      4. Disconnect the headlamp electrical connector.
      5. Remove the headlamp assembly from the vehicle.
      6. Remove the headlamp bulb cover from the headlamp assembly.
      7. Remove the headlamp bulb socket from the headlamp assembly.
      8. Remove the headlamp bulb.
      9. Remove the side marker bulb socket from the outer side of the headlamp assembly.
      10. Remove the side marker bulb.

    Feb 12, 2009 | 2006 Cadillac SRX

    Not finding what you are looking for?
    1999 Mercedes-Benz E-Class Logo

    Related Topics:

    90 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mercedes-Benz Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22041 Answers

    yadayada
    yadayada

    Level 3 Expert

    70346 Answers

    Michael Contreras
    Michael Contreras

    Level 2 Expert

    166 Answers

    Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...