2002 Pontiac Montana Logo
Posted on Nov 08, 2008
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

2002 montana program key fob

2002 Montana - how to reprogram key fob - just bought a used Montana with two fobs and neither work.

Answer This Question
  • 2 more comments 
  • barirw Nov 08, 2008

    I did try new batteries to no avail - Thank you!!!!!!!!!!

  • Anonymous Jan 10, 2009

    I have a 2005 montana and followed the directions to a T. I can't get it to work and this is a brand new oem remote. Please tell me what I'm doing wrong @ [email protected]. Thanks in advance for your help

  • Anonymous Mar 12, 2014

    Reprogram skoda keys

  • Anonymous Mar 12, 2014

    1 series key fobs some times work,some times dont

×

1 Answer

Anonymous

Level 2:

An expert who has achieved level 2 by getting 100 points
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.
Sergeant:

An expert that has over 500 points.

  • Expert 229 Answers
  • Posted on Nov 08, 2008
Anonymous
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.
Sergeant:

An expert that has over 500 points.

Joined: Nov 06, 2008
Answers
229
Questions
2
Helped
93763
Points
621

Key fobs tend to hold their code indefintely. The batteries in them are probably burnt. Open up one of the fobs and replace the battery (hearing aid type) then they should work fine. Good Luck!~

  • Anonymous Nov 08, 2008

    Ok here is the procedure.

    Program only one at a time.

    Remove ignition key.

    Remove the BCM PRGRM fuse from fuse panel. Refer to fuse block in wiring systems.

    Close all the doors.

    Close the liftgate.

    Turn the ignition lock cylinder to ACC

    Turn the cylinder to off then back to ACC within 1 second.

    Open and close any vehicle door. A chime will be heard when the system enters the BCM programming mode.



    Important

    After 7 seconds, a second chime may be heard confirming successful synchronization. It may be necessary to wait approx. 14 seconds dor a second chime that will confirm successful programming.



    Press and hold the transmitter Lock and Unlock buttons simultaneously for 14 seconds.

    Repeat the previous step on each additional transmitter to be programmed.

    Remove the ignition key from the ignition lock cylinder.

    Install the BCM PRGRM fuse back intothe fuse panel. Refer to fuse block in wiring systems.

×

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

Number 7 fuse inside instrument fuse panel RFA mdls 10 amp what is that for?
Remote Function Actuator. key fob operates this


copy and paste
https://www.justanswer.com/pontiac/7saqv-pontiac-montana-sv6-2005-pontiac-montana-want.htmllightning bolt to illuminate
Read full answer
Jan 22, 2024 • Cars & Trucks
0helpful
1answer

06 Montana SV6 already has 4 remotes program to it. can this be cleared or do you have to replace B.C.M.
So what it has 4 key fobs programmed , what is it you want to do ? Why would you want to clear them ? Lost them ?, don't work ? No you wouldn't need to replace the body control module . When programming new fobs , all the one's need to be programmed at same time . All old ones will be erased automatically .
Read full answer
May 01, 2019 • Cars & Trucks
0helpful
1answer

I am trying to program my key fob on a 2005 Pontiac Montana sV6. All the instructions state to turn the key to ACC which they claim is turning the key toward you.
my sv6 wouldnt go in learning mode by using the litlle programer they sell with then fob i did it with the snap on scanner and work fine
Read full answer
Nov 21, 2017 • Pontiac Cars & Trucks
0helpful
2answers

My fobs need to be reprogrammed
because of remote start fob needs to be flashed at dealer
Read full answer
Jul 30, 2017 • 2006 Pontiac Montana
2helpful
1answer

How to program key fob on 06 Montana SV6 without tech 2
There is no onboard programming procedure for this vehicle. This vehicle requires special equipment be connected to the vehicle to program the keyless remote.
Read full answer
Nov 05, 2012 • 2006 Pontiac Montana SV6
1helpful
1answer

Pontiac Montana SV6
For instructions on how to program remotes and keys check website below, I use these and they are usually very accurate. This website does state that on your vehicle, special equipment is needed to program a key fob, as there is no onboard programming for it. However, there are programming instructions for transponder keys.
http://www.programautokeys.com/

http://www.programautokeys.com/
Read full answer
Feb 15, 2010 • Pontiac Montana SV6 Cars & Trucks
18helpful
6answers

Where is the bcm program fuse on a 2005 pontiac montana sv6
The BCM program fuse on a 2005 Montanna SV6 is called something different in the manual. It's called a “Keyless Entry Module” fuse and it is fuse #7. The fuse panel is located on the passenger side on the side of the dash. There is a cover with an indent hole in it to pull the fuse cover off. It's really hard to pull it off and it almost seems like your going to break it when your trying to get if off. Keep pulling, it will come off! On the fuse cover, fuse #7 is labeled " RFA MDLS" which is again different than what is in the manual. I followed the procedure to reprogram my "Key Fob" and within 45secs, I had reprogrammed my key FOB! I was so excited, because, I have been trying locate the BCM fuse for 4 weeks. I think GMC does not want us to know it’s location or name, so you would have to go into a dealership to get your Key Fobs reprogrammed costing about a $100 for a minute of work.
e65ae06.jpg


1. Keep the windows open as a safety measure, then,
2. Remove the ignition key from the ignition lock cylinder.
3. Remove the “RFA MDLS” (fuse #7 ,BCM PRGRM fuse, Keyless Entry fuse) from the fuse panel.
4. Close all of the doors.
5. Close the liftgate.
6. Turn the ignition lock cylinder to ACC.
7. Turn the ignition lock cylinder to OFF, and then back to ACC within 1 second.
8. Open and close any vehicle door. A chime will be heard when the system enters the BCM programming/diagnostic mode.
9. Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds.
10. Important
After 7 seconds, a chime may be heard confirming successful programming.
11. Repeat the previous step on each additional transmitter to be programmed.
12. Remove the ignition key from the ignition lock cylinder
13. Install the “RFA MDLS” fuse ( fuse #7 ,BCM PRGRM fuse, Keyless Entry fuse) back into the fuse panel.
14. Press on the key fob functions (EG. Lock, Unlock) to verify correct operation.
Read full answer
Mar 17, 2009 • 2006 Pontiac Montana SV6
0helpful
1answer

2005 Pontiac SV6 Montana key fob unlocks doors but will not lock
For the sliding doors you need to clean the contacts, there are 6 or 8 on both sides, just wipe them clean as they are probably covered in oil/grease/grime.
Read full answer
Feb 12, 2009 • 2006 Pontiac Montana SV6
1helpful
1answer

Program key fob 1999 sillouette
Take it to A GM Dealer they Hook into the ALDL and Reprogram it By Way of a Scanner
Read full answer
Feb 05, 2009 • 1999 Oldsmobile Silhouette
1helpful
2answers

Key fob broke where the key ring goes
that is it just a replacement kit available/ Please rate my response thank you very much
Read full answer
Dec 28, 2008 • 2003 Pontiac Montana
Not finding what you are looking for?

View Most Popular

2002 Montana

  • Cars & Trucks

Related Question

Number 7 fuse inside instrument fuse panel RFA mdls 10 amp what is that for?

  • Cars & Trucks

Related Topics

1,458 views

Ask a Question

Usually answered in minutes!

Popular Questions

What does a low oil pressure alarm mean

2001 Pontiac Montana

Passanger power window will go down but not up..and its cold out.

2004 Pontiac Montana

2000 pontiac montana wipers stuck

2000 Pontiac Montana

How tough is it to replace the rack and pinion on a pontiac montana

2001 Pontiac Montana

How to replace a radiator

2002 Pontiac Montana

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Pontiac Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...