Question about Jeep Wrangler

1 Answer

2004 jeep wrangler have no back up lights...checked the back up switch and fuses and bulds all good. help....

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 51 Answers

Check the wiring that goes to the reverse light you may have a broken or loose wire also check inside the bulb socket for corrosion that would also cause it no to work.

Posted on Nov 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 jeep wrangler tj my dash lights and running lights arent working the fuses are good what else could it be


There are fusible links which could fail, usually in the wiring from the battery + or located near the starter motor. Also possible you have a bad light switch. Use a voltmeter to find this.

Dec 12, 2014 | 2004 Jeep Wrangler

1 Answer

How to keep interior lights on after turning off ignition?


the dimmer swtich is part of your light switch. dim to full on postition to keep the interior light on. If this does not work then your switch may be bad; assuming the fuse and bulb are good. Check your owners manual for specifics.

Oct 22, 2010 | 2004 Jeep Wrangler

1 Answer

I have a 1999 Jeep TJ, the wipers, radio and turn signals all stopped working. Checked fuses, nothing seems blown. Also, they all work when the ignition switch is in the accessories position, but when...


Had the same thing with my 2004 Wrangler. The Airbag light stayed on also. Took to dealer - Cost $400 for them to replace the ignition. Fixed every thing.

Sep 14, 2010 | 1999 Jeep Wrangler

1 Answer

I was wiring a trailer pigtail to an 06 wrangler and blew the turn signal bulbs but the fuses are good. I have running and reverse lights but no brake lights or turn signals


If the bulbs and the fuses are good, check the brake light switch. You might of shorted out the switch when working on the pig tail. Always use a test light or volt meter when installing pig tails. This way you can check for power and ground before hooking a wire up to help prevent shorts. But by what you have said it does sound as if the brake light switch is now bad.

Jun 27, 2010 | 2006 Jeep Wrangler

1 Answer

2004 jeep wrangler brake lights don't come on


just follow the wires from the brake lights and you'll see the ground. its probably coroded

Mar 09, 2010 | 2004 Jeep Wrangler

1 Answer

I have a 2004 jeep wrangler the running lights come on and dirrectionals come on also, after checking fuse's and bulbs and replacing brake switch,i still have no brake lights,can someone help me


you have a bad ground the brake light are independent of the rest of the lights if the turn signals work and the brake lights don't you have a bad ground blowen fuse or your turn signals are not grounded properly so the turn signal lights may be dim or erritic in nature you can also check the blinker switch for it can be shorted (remember that there are two 1 for the turnsignals & 1 for the fourway flashers

Mar 09, 2010 | 2004 Jeep Wrangler

1 Answer

What size fuse goes in position #4? What are


From the Jeep TJ Wrangler 2004 - Owners Manual (Section 7, Page 255):
Fuse 4 -->> 10 Amp Red -->> Door Switch Defeat
Fuse 16 -->> 10 Amp Red -->> Headlamp Aim (Export only)
Fuse 20 -->> 20 Amp Yellow -->> Transmission: Manual - Clutch Interlock switch by-pass Automatic - Ignition Starter Circuit

I really hope helps with this (remember rated this help). Good luck.

Dec 16, 2009 | 2003 Jeep Wrangler

2 Answers

2004 jeep wrangler won't start. No sound, no lights on the dashboard. the gauges jump once. What is causing that?


If there is no lights on the dashboard and no sound etc..the first thing you need to check is your battery..It may be a fuse as well somewhere...

Sep 05, 2009 | 2004 Jeep Wrangler

2 Answers

2000 Jeep Wrangler, electrical issue


if the 3ed brake light works , rapidly move hazard switch back & forth & recheck, if they now work change turn signal switch , they are being canceled by switch

Sep 06, 2008 | 2000 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...