Suzuki 1988 Samuri

Put car in neutral, remove wheels, calipers and rotors, diff. cover. rotate carrier until you see wrist pin retaining bolt, remove bolt and slide out the wrist pin out of carrier. Next push axle inward to remove inner axle "C" retainer washer then slide axle out of tube. Then pry off axle seal and with slide hammer w/attachment remove axle bearing.

• Air Suspension
• Front Suspension
• Rear Suspension
• • Coil Spring Rear Suspension
  • Coil Springs
  • Lower Ball Joint
  • Lower Control Arms
  • Shock Absorbers
  • Stabilizer Bar Sway Bar
  • Strut Macpherson Strut Assembly
  • Upper Control Arms
  • Wheel Bearings
• Specifications
• Wheel Alignment

• HOME
• REPAIR INFO
• 1999 LEXUS ES300 3.0L SFI DOHC 6CYL REPAIR GUIDE
• SUSPENSION
• REAR SUSPENSION
• COIL SPRING REAR SUSPENSION

Lexus Car ES, IS, LS 1998-06
Coil Spring Rear Suspension

• HUB & BEARINGS
• STABILIZER BAR
• STRUT & COIL SPRING

Print

Hub & Bearings

Adjustment
Check the backlash in bearing shaft direction and the axle hub deviation. Maximum for backlash should be 0.0020 in. (0.05mm) and for axle hub deviation 0.020 in. (0.05mm).

Fig. Checking wheel bearings for excessive play


NOTE The rear wheel bearings are non-adjustable. If the wheel bearing is out of specifications, replace the wheel bearing.
Removal & Installation

1. Before servicing the vehicle, refer to the Precautions section.
2. Raise and safely support the vehicle.
3. Remove or disconnect the following:
   
   Rear tire and wheel assembly Rear stabilizer link Rear axle shaft nut Rear disc brake caliper and disc Speed sensor Parking brake assembly at the wheel hub No. 1 and 2 upper control arm assembly No. 1 and 2 rear suspension arm assembly Toe control link Rear axle from hub assembly using a plastic hammer No. 2 rear wheel bearing dust deflector using a screwdriver 4 bolts and rear axle hub and bearing assembly from the axle carrier assembly
   

To install:

1. Install or connect the following:
   
   Hub on the carrier and tighten the bolts to 52 ft. lbs. (70 Nm) No. 2 rear wheel bearing dust deflector using a screwdriver Rear axle into hub assembly No. 1 and 2 upper control arm assembly. Torque the new nut to the No. 2 rear upper control arm to 52 ft. lbs. (70 Nm). Temporarily tighten the No. 1 arm bolt. No. 1 and 2 rear suspension arm assembly. Temporarily tighten. Toe control link. Torque new nut to 52 ft. lbs. (70 Nm). Rear stabilizer link. Torque to 20 ft. lbs. (27 Nm). Parking brake assembly at the wheel hub Rear speed sensor Rear axle shaft nut. Torque to 214 ft. Lbs. (290 Nm) and stake the nut with a chisel and hammer. Rear brake disc and disc brake caliper
   
2. Adjust the parking brake.
3. Stabilize the suspension as follows :
   1. Install the wheel(s).
   2. Lower the vehicle and bounce it up and down several times to stabilize the rear suspension.
   3. Raise the vehicle.
   4. Remove the wheel.
   5. Jack up the rear lower suspension armplacing a wood block in between. Apply a load to the suspension so that the lower suspension arm is plkaced in a horizontal position.
   
   
4. Fully tighten the No. 1 rear upper control arm assembly to 119 ft. lbs. (161 Nm).
5. Fully tighten the No. 1 rear suspension arm assembly to 70 ft. lbs. (95 Nm).
6. Fully tighten the No. 2 rear suspension arm assembly to 119 ft. lbs. (161 Nm).
   
   Rear tire and wheel assembly
   

1. Before servicing the vehicle, refer to the Precautions section.
2. Raise and safely support the vehicle.
3. Remove or disconnect the following:
   NOTE If it is necessary to replace the hub or bearing, replace the components as an assembly.
   
   
   Rear tire and wheel assembly If equipped with rear disc brakes, the caliper mounting bolts. Leave the brake line connected and suspend the assembly out of the way. Brake rotor or drum 4 bolts and pull off the rear axle hub O-ring
   

To install:

1. Install or connect the following:
   
   Hub on the carrier and tighten the bolts to 59 ft. lbs. (80 Nm) Rotor or drum Caliper, f equipped with rear disc brakes and tighten the bolts to 34 ft. lbs. (64 Nm) Wheel
   

1. Before servicing the vehicle, refer to the Precautions section.
2. If equipped with air suspension, move the height control switch in the trunk area to the OFF position.
3. Remove or disconnect the following:
   
   Negative battery cable Rear wheel(s) Height control sensor link from the lower control arm Anti-lock Brake System (ABS) speed sensor and wiring harness Brake caliper bracket from the rear axle carrier by removing the 2 bolts. Support the caliper with a piece of wire. Brake rotor Parking brake shoes and cable Cotter pin, lock cap and the nut holding the halfshaft to the rear axle Suspension member brace by removing the 2 bolts Halfshaft bolts and washers Halfshaft from the vehicle Strut rod
   
4. Place matchmarks on the adjusting cam and body for the No. 1 control arm.
5. Remove or disconnect the following:
   
   Nut and adjusting cam Nut on the axle carrier side of the No. 1 lower control arm Separate the control arm from the axle carrier No. 1 lower control arm Stabilizer bar link from the No. 2 lower control arm.
   
6. Place matchmarks on the adjusting cam and body.
7. Remove or disconnect the following:
   
   Nut and adjusting cam from the No. 2 lower control arm Nut and bolt holding the No. 2 lower control arm to the axle carrier No. 2 control arm from the vehicle Nut and bolt on the lower side of the strut assembly 2 upper control arm set nuts and bolts Axle carrier with the upper control arm
   
8. Secure the axle carrier in a vise.
9. Remove or disconnect the following:
   
   Nut holding the upper control arm to the axle carrier and remove the control arm Dust deflector. Use a suitable prytool. Oil seal
   
   

   Fig. Removing the oil seal (inner)-LS 430
   
   

10. Remove the 2 bolts and nuts and shift the backing the plate towards the hub side (outside).
11. Remove or disconnect the following:
    
    Axle hub
    
    

    Fig. Removing the axle hub from the axle carrier-LS 430
    Backing plate. Inner race (outside) from the axle hub
    
    

    Fig. Removing the inner race (outside) from the axle hub-LS 430
    Oil seal (outer) from the axle
    
    

    Fig. Removing the oil seal (outer)-LS 430
    Snapring from inside the axle housing Bearing from the axle housing
    

To install:

1. Install or connect the following:
   
   New bearing to the axle housing Snapring to the axle carrier, using snapring pliers New outer oil seal. Coat the oil seal lip with multipurpose grease.
   
   

   Fig. Installing the oil seal (outer)-LS 430
   Backing plate to the axle housing. Do NOT install the bolts or nuts at this time. Inner race (inside) to the axle housing Axle hub to the axle housing Backing plate in position. Tighten the bolts and nuts to 43 ft. lbs. (59 Nm). New oil seal (inner) to the axle housing. Coat the oil seal lip with multipurpose grease.
   
   

   Fig. Installing the oil seal (inner)-LS 430
   New dust deflector. Be sure to align the hose for the ABS speed sensor in the dust deflector and axle carrier. Upper control arm to the axle carrier by installing the nut. Tighten the nut to 80 ft. lbs. (108 Nm). Axle carrier and upper control arm to the vehicle as an assembly 2 upper control arm set bolts and tighten the bolts to 121 ft. lbs. (164 Nm) Bolt and nut holding the strut to the axle carrier. Tighten to 101 ft. lbs. (137 Nm). Bolt and nut connecting the No. 2 lower control arm to the axle carrier. Tighten the bolt to 60 ft. lbs. (81 Nm). Nut and adjusting cam to hold the No. 2 lower control arm to the body. Align the adjusting cam marks and tighten the nut to 57 ft. lbs. (78 Nm). Stabilizer bar link to the No. 2 lower control arm and tighten the nut to 48 ft. lbs. (65 Nm) No. 1 lower control arm to the axle carrier and body. Install the nut to hold the No. 1 lower control arm to the axle carrier. Tighten the nut to 43 ft. lbs. (59 Nm). Nut and adjusting cam to hold the No. 1 lower control arm to the body. Align the matchmarks and tighten the nut to 57 ft. lbs. (78 Nm). Strut rod to the axle carrier and body. Install the bolt and nut to hold the strut rod to the body. Tighten to 57 ft. lbs. (78 Nm). Bolt and nut to hold the strut rod to the axle carrier. Tighten to 136 ft. lbs. (184 Nm) Parking brake shoes and cable Outboard joint side of the halfshaft and align the matchmarks on the side gear shaft and the halfshaft. Coat the threads with clean oil and install the hexagon bolts. Tighten bolts to 61 ft. lbs. (83 Nm). Suspension member brace with the 2 bolts. Tighten the 2 bolts to 37 ft. lbs. (50 Nm). Nut to hold the halfshaft to the rear axle. Tighten the nut to 213 ft. lbs. (289 Nm). Lock cap and cotter pin Brake disc to the axle hub with the matchmarks aligned. Install the 2 screws and tighten the screws to 48 inch lbs. (5 Nm). Brake caliper to the vehicle and install the 2 bolts. Tighten the bolts to 77 ft. lbs. (104 Nm). ABS speed sensor and wiring harness Height control sensor link with the matchmarks aligned. Tighten the nut to 48 inch lbs. (5 Nm). Rear wheel(s) Negative battery cable
   

2. Lower the vehicle and turn ON the air suspension switch.

Fig. Exploded view rear carrier assembly, hub and bearing-

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
   WARNING Be careful not to damage the boot and ABS sensor
   
   
   Rear wheel(s) Height control sensor link from the lower control arm Anti-lock Brake System (ABS) speed sensor and wiring harness Brake caliper bracket from the rear axle carrier by removing the 2 bolts. Support the caliper with a piece of wire. Brake rotor Parking brake shoes and cable Toe control link Separate upper control arm assembly Shock absorber from axle carrier Suspension arms No 1 and 2 from axle carrier Rear axle from carrier
   
   
   Wheel bearing dust deflector 4 bolts and axle & bearing hub assembly
   

To install:

1. Install or connect the following:
   
   4 bolts and axle & bearing assembly. Tighten to 48 ft. lbs (65 Nm) Rear wheel bearing dust deflector Rear drive axle Upper control arm. Temporarily tighten No 2 and No 1 suspension arms. Tighten to 52 ft. lbs. (70 Nm) Shock absorber. Temporarily tighten Toe control link. Tighten to 37 ft. lbs. (50 Nm) Fully tighten upper control arm. Tighten to 52 ft. lbs. (70 Nm) Height control sensor Parking brake shoes and cable Speed sensor Rear disc brake caliper Fully tighten shock with new nut to 52 ft. lbs. (70 Nm) Rear tire
   
2. Inspect and adjust rear wheel alignment
3. Check ABS speed sensor signal

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
   
   Rear wheel Wheel speed sensor Axle halfshaft Brake caliper and rotor Parking brake shoes Parking brake cable No. 1 lower suspension arm bolt No. 2 lower suspension arm bolt Toe control link Upper ball joint Axle carrier from the vehicle
   
3. Press the hub out of the wheel bearing, then remove the backing plate.
4. Remove the snapring, then press the wheel bearing out of the axle carrier.

To install:

NOTE Use a new toe control link nut for assembly.

1. Installation is the reverse of the removal procedure, while using the following torque values:
   
   Backing plate bolts: 43 ft. lbs. (59 Nm) No. 1 lower suspension arm bolt: 55 ft. lbs. (75 Nm) No. 2 lower suspension arm bolt: 81 ft. lbs. (110 Nm) Toe control link nut: 36 ft. lbs. (49 Nm) Upper ball joint nut: 80 ft. lbs. (108 Nm) Brake caliper support bolts: 77 ft. lbs. (104 Nm) Rear wheel lug nuts: 76 ft. lbs. (103 Nm)
   

Fig. Exploded view rear Axle carrier and hub assembly-ES 330

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
   
   Rear tire and wheel assembly Brake caliper support bracket Brake rotor Skid control sensor wire 4 bolts and rear hub and bearing assembly Skid control sensor
   

To install:

1. Install or connect the following:
   NOTE Inspect bearing back lash and hub deviation
   
   
   Skid control sensor Rear axle hub and bearing assembly with 4 bolts. Tighten to 59 ft. lbs. (80 Nm) Skid control sensor wire
   
   
   Rear disc Rear disc brake caliper assembly. Tighten to 46 ft. lbs (62 Nm) Flexible brake hose Rear tire and wheel
   
2. inspect and adjust rear wheel alignment
3. Check ABS speed sensor signal

Stabilizer Bar

Removal & Installation

1. Remove the rear wheels.
2. Remove the 2 nuts and left stabilizer bar link. If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud. Repeat for the right side.
3. Remove the 8 bolts, 2 No. 1 brackets and 2 bushings. Two types of bolts are used, so make sure the correct bolts are installed.
4. Remove the stabilizer bar.

To install:

1. Install the stabilizer bar.
2. Install the bushing and bracket with the 2 bolts and tighten to 14 ft. lbs. (19 Nm). Install the bushing to the inner side of the bushing stopper on the stabilizer bar.
3. Connect the stabilizer bar links and tighten the nuts to 29 ft. lbs. (39 Nm). Repeat for the right side.
4. Install the rear wheels.
5. Inspect and adjust rear wheel alignment.

Strut & Coil Spring

Removal & Installation

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
   CAUTION Do NOT remove the center nut to the strut at this time. The spring on the strut is under high pressure and can cause serious injury.
   
   
   No. 2 luggage compartment trim cover Left and right deck side trim box Rear luggage compartment trim cover Front luggage compartment trim cover Left and right side luggage compartment trim covers Rear wheel Rear wheel fender liner No. 2 differential support protector Rear suspension member brace Rear No. 2 lower control arm Mounting bolts and strut assembly
   
3. Secure the strut in a vise.
4. Compress the coil spring
5. Remove or disconnect the following:
   
   Upper strut retaining nut Suspension support Upper insulator Bumper Coil spring Insulator

you don't repair it, you replace it. jack it up, remove the brakes, and all the brake assembly from that axle,, http://www.ehow.com/way_5731956_ford-rear-brake-replacement-instructions.html then remove the bearing cap,, cotter pin, and nut from the spindle , ( you might want to replace the wheel bearing at the same time due to the bad axle ) remove the axle bolts,, and shock bolts, from the axle beam. remove axle beam assembly

REMOVAL & INSTALLATION 1983-86 Models

1. On 4-door sedan, remove the package tray and vent duct.
2. On hatchback, remove the speaker grilles.
3. Disconnect the brake line from the wheel cylinder. CAUTION
   Brake fluid contains polyglycol ethers and polyglycols. Avoid contact with the eyes and wash your hands thoroughly after handling brake fluid. If you do get brake fluid in your eyes, flush your eyes with clean, running water for 15 minutes. If eye irritation persists, or if you have taken brake fluid internally, IMMEDIATELY seek medical assistance.
   
4. Remove the brake line from the brake hose.
5. Disconnect the brake hose from its bracket on the shock absorber.
6. Loosen, but do not remove, the nut holding the suspension support to the shock absorber.
7. Unbolt the shock absorber from the rear arm.
8. Unbolt and extract the shock absorber from the body. To install:
   
9. Attach the shock absorber to the body and tighten the 3 nuts to 17 ft. lbs. (25 Nm).
10. Engage the shock absorber bracket with the carrier and install the hardware. Tighten the nuts to 119 ft. lbs. (162 Nm).
11. Tighten the center suspension support nut to 36 ft. lbs. (49 Nm). There is a bearing located under the suspension support dust cover. Remove the dust cover and pack the bearing with multi-purpose grease. Once packed, reinstall the dust cover.
12. The remainder of installation is the reverse of removal. Tighten each component to specifications.
13. Have the rear wheel alignment checked.

1987-88 Models

1. On wagon models, remove the toneau cover holder.
2. Loosen the rear wheel lug nuts, raise the rear of the vehicle and support it safely. Block the front wheels.
3. Remove the rear wheels.
4. Using the proper size flare nut wrench, disconnect the backing plate hardware.
5. With a flare nut and a back-up wrench, disconnect the brake tube from the brake hose and use a small plastic container to collect the brake fluid.
6. Undo the clip and disconnect the brake hose from the shock absorber. NOTE: Before the axle bolts are removed, the axle carrier must be supported with a jack.
   
7. Support the axle carrier with a floor jack and remove the mounting bolts and nut. Disconnect the axle carrier from the shock absorber.
8. Support the shock absorber firmly by hand and remove the three mounting nuts. Remove the shock absorber from the body. To install:
   
9. Position the shock absorber onto the body and support it firmly by hand. Install the three nuts and tighten them to 23 ft. lbs. (31 Nm).
10. Attach the axle carrier to the shock absorber with the nuts and bolts. Tighten the nuts to 166 ft. lbs. (226 Nm).
11. The remainder of installation is the reverse of removal. Tighten each component to specifications.
12. Bleed the brake lines as described in Section 9.
13. Have the rear wheel alignment checked.

1989-96 Models

1. On the 4-door sedan, remove the package tray and vent duct. On 1992-96 models, it will be necessary to remove the rear seat back.
2. On the hatchback, remove the speaker grilles.
3. On the wagon models remove the tonnue cover and rear seat back.
4. Loosen the rear wheel lug nuts, raise the rear of the vehicle and support it safely. Block the front wheels.
5. Remove the rear wheels.
6. Disconnect the brake hose and the ABS speed sensor from the shock absorber.
7. If equipped with ABS, disconnect the Load Sensing Proportioning Valve (LSPV) spring from the lower arm.
8. Disconnect the stabilizer bar link from the shock absorber.
9. Support the rear axle and loosen the 2 bolts from the lower end of the shock absorber.
10. From inside the vehicle, unbolt the upper support. Fig. 1: A rubber cap covers the rear shock absorber tower nut
    Fig. 2: The upper shock absorber tower is retained by the center nut (circled) and three surrounding nuts
    
    
11. Lower the rear axle carrier and remove the two bolts.
12. Remove the shock absorber from the vehicle. To install:
    
13. Install the shock absorber assembly onto the vehicle.
14. Connect the brake hose and the ABS speed sensor to the shock absorber.
15. Connect the stabilizer bar link to the shock absorber.
16. Install the wheel and tire assembly.
17. During installation, please observe the following tighten specifications:
    1. Tighten the shock absorber-to-body bolts to 29 ft. lbs. (39 Nm).
    2. Tighten the shock absorber-to-axle carrier nuts to 166 ft. lbs. (226 Nm) on 1988-91 vehicles and 188 ft. lbs. (255 Nm) on 1992-96 vehicles.
    3. Tighten the suspension support-to-shock absorber nut to 36 ft. lbs. (49 Nm) on 1988-91 vehicles. On 1992-96 models, tighten the stabilizer bar link to shock absorber retainers to 47 ft. lbs. (64 Nm).
18. Install the rear seat back, vent duct and the package tray as required.

Hub & Bearing Removal & Installation To Remove:
Hub bearing assembly (Typical)

1. Release parking brake.
2. Remove rear wheel assembly.
3. Remove rear wheel speed sensor from carrier.
4. Dismount brake caliper and support with mechanic's wire.
5. Remove brake disc.
6. Remove 4 axle hub mounting bolts. Special tool 09432-11000 (Typical)
   
   
7. Using tool 09432-11000 (or suitable gear puller), remove tone wheel.
8. Remove carrier.
9. Remove stakes and remove flange nut.
10. Support bearing outer race flange and press rear axle hub out.
11. Using tool 09432-11000 (or suitable puller), remove inner race from axle hub.

To Install:
Hub bearing assembly (Typical)

1. Apply thin coat of grease to bearing contact surface and hub.
2. Using and appropriate tool, press bearing into hub. CAUTION
   Do not press against outer race of wheel bearing.
   
3. Install flange nut and stake nut until it meets concave portion of spindle.
4. Install carrier.
5. Use an appropriate tool to press tone wheel.
6. Install hub/bearing assembly with rounded portion of outer race facing up.
7. Install 4 hub/bearing assembly bolts and rotate hub to seat bearing.
8. Measure wheel bearing starting torque with a spring balance or equivalent device.
   • Starting torque should measure 15.9 in lb (1.8 Nm) or less
9. Install brake disc.
10. Mount brake caliper.
11. Install rear wheel speed sensor to carrier.
12. Install rear wheel assembly.

the bearing has 4 bolts holding it on the inner side facing the axle. remove the wheel and brakes to get access to it

Its pretty simple.
1. take off wheel
2. take off brake caliper, caliper bracket, and rotor.
3. remove axle nut which secures axle into the bearing
4. should be 3 bolts on the flange which hold the whole wheel bearing/hub unit on.
5. reverse for reassembly

The wheel hub and bearing are all one assembly and are bout as a unit.


Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/sean_54c3a3dc48a7773c

Section 05-02A: Axle, Integral Carrier — 8.8-Inch Ring Gear 1994 Town Car, Crown Victoria/Grand Marquis. Workshop Manual REMOVAL AND INSTALLATION Axle Shaft NOTE: Whenever replacing the rear axle lubricant, use Rear Axle Lubricant XY-90-QL (ESP-M2C154-A) or equivalent.
Removal
CAUTION: The rear brake anti-lock sensor must be removed before the axle shafts are removed. The rear brake anti-lock sensor is bolted on the rear disc brake caliper anchor plate.

1. Raise vehicle to desired working height. Refer to Section 00-02 . Remove rear wheel (1007) and tire assembly. Remove rear disc brake calipers (2552) and rear disc brake rotors (2C026) .
   
   
   
   
   

1. Clean all dirt from area of axle housing cover with a wire brush and/or cloth.

1. Drain rear axle lubricant by removing the axle housing cover .

1. Remove differential pinion shaft lock pin and differential pinion shaft .
   
   
   
   

1. Push flanged end of the axle shafts toward the center of the vehicle and remove the rear axle shaft retaining u-washer from the button end of the axle shaft .
   
   
   
   

1. Remove axle shaft from the rear axle housing , being careful not to damage the inner wheel bearing oil seal (1177) and rear brake anti-lock sensor ring.

Installation
NOTE: Check for presence of rear axle shaft o-ring (4A332) on the spline end of the shaft and install if not present.
CAUTION: Care must be taken not to let axle shaft splines damage oil seal or bearing assembly.

1. Carefully slide axle shaft into rear axle housing without damaging rear wheel bearing (1225) or rear brake anti-lock sensor indicator (2C189) . Start splines into side gear and push firmly until the button end of axle shaft can be seen in the differential case .

1. Install the rear axle shaft retaining u-washer on the button end of the axle shaft splines, then pull the shaft outboard until the shaft splines engage and the rear axle shaft retaining u-washer seats in the counterbore of the differential side gear .

1. Position the differential pinion shaft through the differential case and differential pinion gears , aligning the hole in the differential pinion shaft with the lock bolt hole. Apply Rear Axle Lubricant to differential pinion shaft lock pin . Install differential pinion shaft lock pin and tighten to 20-41 Nm (15-30 lb-ft). CAUTION: Differential pinion shaft lock pin must be tightened to specification using Stud and Bearing Mount E0AZ-19554-BA (WSK-M2G349-A1) or equivalent.
   
   
   
   
   NOTE: Axle housing cover must be installed within 15 minutes of application of the silicone rubber or new silicone rubber must be applied.
   CAUTION: Make sure machined surfaces on both axle housing cover and rear axle housing are clean before installing the new silicone sealant. Inside of axle must be covered when cleaning the machined surface to prevent axle contamination. Tighten the cover bolts in a crosswise pattern to ensure uniform draw on axle housing cover .
   

1. Apply Silicone Rubber D6AZ-19562-AA or BA (ESB-M4G92-A or ESE-M4G195-A) or equivalent. Install axle housing cover and tighten retaining bolts to 28-38 Nm (38-52 lb-ft).
   
   
   
   

1. Add Motorcraft Rear Axle Lubricant XY-90-QL or KL (ESP-M2C154-A) or equivalent until it is 6-14mm (1/4-9/16 inch) below bottom of fill hole. Add 118.3 mL (4 oz) of Ford Additive Friction Modifier C8AZ-19B546-A (EST-M2C118-A) or equivalent to Traction-Lok axles. Install fill plug and tighten to 20-41 Nm (15-30 lb-ft).

1. Install rear brake anti-lock sensor indicator . Tighten retaining bolt to 4.5-6.8 Nm (40-60 lb-in).

1. Install rear disc brake caliper and rear disc brake rotor .

1. Install wheels and tires.

---------------------------------------------------------

1. Insert Rear Bearing Remover T85L-1225-AH in bore and position it behind bearing so tangs on tool engage bearing outer race. Remove rear wheel bearing and inner wheel bearing oil seal as a unit, using Impact Slide Hammer T50T-100-A.
   
   Rear Disc Brake Caliper Anchor Plate
   
   
   
   
   

1. Lubricate the rear wheel bearing with Rear Axle Lubricant.
   
   
   
   

1. Install rear wheel bearing into the housing bore using Axle Tube Bearing Replacer T78P-1225-A.
   
   
   
   CAUTION: Installation of rear wheel bearing or inner wheel bearing oil seal assembly without proper tool may result in an early bearing or seal failure. If inner wheel bearing oil seal becomes cocked in bore during installation, remove it and install a new one.
   

1. Install the inner wheel bearing oil seal using Axle Tube Seal Replacer T78P-1177-A. Use Premium Long-Life Grease XG-1-C or K (ESA-M1C75-B) or equivalent between the lips of the inner wheel bearing oil seal .
   
   
   
   

1. Install axle shafts as outlined.

jack & support vehicle. remove rear axle cover drain fluid, removeleft rear tire drum/rotor brakes, remove bolt in axle housing that holds the 3/4 inch pin in place pull pin , push left axle shaft inwards and remove c clip from inside axle case,slide out axle shaft,remove seal,remove bearing and install in revers