Question about 1986 Isuzu Pickup

1 Answer

86 isuzu clutch- master cylinder ran dry

Truck clutch seems to be stuck engaged,it starts without depressing the clutch,wont go into any gears.the master cylinder ran dry but i dont have anything else to go on--please help!

Posted by on

  • straunyboy Nov 12, 2008

    clutch returns on its own-system was bled but cant locate slave cylinder-still has same problem

  • Anonymous Apr 01, 2014

    Clutch master cylinder

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 98 Answers

Did you bleed the system? There is probably a bleeder on the slave cylinder and you may need to jemmy the selector fork/ Also look fro a damper valve between the master and slave cylinder... it will need bleeding too.

Posted on Nov 07, 2008

  • ChasDaihard Nov 12, 2008

    Try this site:

    http://www.autozone.com/az/cds/en_us/090...


×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I just put a new slave cylinder and clutch master cylinder on a 2003 Honda accord 3.0 V6 six speed and you can shift the gears without the clutch pedal pushed in or the car started


that is normal if the gear synchro dogs ( teeth) are in line in the box
problems concerning a clutch are
slashing gears when trying to engage first or reverse with the pedal to the floor ---needs bleeding
slipping when the clutch pedal is released--- slipping clutch from the pressure not being released ---problem in master cylinder
reverse gear is the only gear not synchronised so even with the clutch depressed it is possible sometimes that it will not go into gear unless you let the clutch up to move the gears in the box then attempt to re-engage reverse

May 04, 2016 | Honda Cars & Trucks

2 Answers

99 Isuzu rodeo "99 Isuzu rodeo 5 speed stuck in 4th gear stalls when forced into neutral" triple posted now.


see your other post Richard, the transmission, gearbox is fairly complicated and any sstatement given here would be seculation.
Whatever
Manual transmission gets stuck

Jul 03, 2015 | Isuzu Cars & Trucks

1 Answer

1998 Honda Civic manual trans will not shift into gears. Car starts, push in clutch and it goes to the floor, release clutch and comes back up. Unable to put into gears. Brake fluid and clutch fluid seem...


Eric, how are you confirming whether or not the car goes into gear if you shift gears without the engine running? One way would be to put it in 1st and see if you can push the car. If you can't, it is in gear.

Another option is to roll the car slightly forward or backward (engine off) while trying to put the car in gear. Once it is in gear, then the car shouldn't move any further. However, if it goes into gear, DO NOT start the car without taking it back out of gear.

The clutch is much more likely to be the problem than the transmission.

If the clutch fluid ever ran dry, then the clutch hydraulics will need to be bled of air. Otherwise, the problem could be the clutch master cylinder, slave cylinder or throwout bearing. Since you didn't report the clutch slipping (e.g. engine revving without accelerating when in gear) it is likely not the clutch disks themselves.

Jun 11, 2014 | Cars & Trucks

1 Answer

1986 isuzu trooper clutch pedal went soft


some of these were manual clutch cable check adjustment of cable at firewall (bulkhead) and check for cracks around where cable goes through to inside cab common on old girls.
if hydraulic clutch system
check fluid in clutch master cylinder is it low?
it could have leaking slave cylinder on gear box bell housing or your clutch needs replacing, gear box out and replace clutch as a kit, pressure plate, clutch plate, thrust bearing (comes as kit) but dont forget to check and or replace the spigot bearing in the rear of the crank shaft when doing clutch kit.

Apr 01, 2014 | 1986 Isuzu Trooper

2 Answers

My clutch won't engage 1997 Honda civic


Clutch plate and pressure plate seem to be too weak to pull the car. To test the clutch plate, park the car on flat surface. Pull the hand brake up, start the car, depress the foot brake pedal, depress the clutch pedal, put the car in 1st gear, press the gas pedal and leave the clutch pedal at once, while keeping the brake pedal depressed.
Follow one of the two following statements:
1. Engine does not shut down and remain start. (Clutch plate, pressure plate and clutch bearing defective - Replace all as a set)
2. Engine shuts down. (Clutch system is OK and does not require any repair).

Apr 06, 2013 | 1997 Honda Civic

1 Answer

Manual 5 speed transmission clutch stuck. It was cold. Clutch itself is good. It appears to be a linkage prob of some sort. The haynes manual wont help because it covers too many diff trucks. mine is a 96...


Your truck has a hydraulic clutch, check to see fluid is full in the clutch master cylinder, and see if fluid is leaking at the line or the slave cylinder, line could have broke, or master/slave cylinder needs replaced.

Feb 08, 2011 | 1996 Ford F150 Regular Cab

1 Answer

Started off with cluth sticking to floor.would have to pull clutch pedal back up with foot. truck would stick in gear. even with clutch fully depressed. seemed like spring had disconnected from clutch...


your clutch uses a hydraulic master and slave cylinder to disengage. It is likely that the slave has been leaking and the reservoir gone dry, thus allowing air into the system and reducing effectiveness. Check the clutch master cylinder reservoir (near the brake reservoir) fluid level. If low, also check the slave cylinder at the clutch for leakage. If leaking, replace the slave and bleed the system. If you need procedures or have more questions, please let us know.

Sep 25, 2010 | 1994 Nissan Pickup

2 Answers

86 ford mustang 5.0 ho motor. just installed a clutch. wont go into gear. the cable has been adjusted. is there a slave cylinder adjustment too? or is the slave cylinder not workin properly


My '86 5.0 was a cable controlled clutch no slave or master cylinders. Make sure the throwout lever is seated properly, and check for movement when the clutch pedal is depressed. It should move at least .75 inches when depressed. Also make sure the bell housing is mating up to the engine completely and all bolts are tight. If all these things are ok it could be an improperly installed or wrong throwout bearing. I hope this helps. I remember what a pain that job was when I did mine esp. that screwy cable pulley thing attached to the clutch pedal. Which also may be the problem. Good luck.

Aug 12, 2009 | 1986 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

488 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...