Question about 2000 Toyota Camry

1 Answer

Part availability I am buying a 2000 Camry that has power front seats.  The plastic trim on the drivers side seat covering the power controls is pulling away from the seat. I have looked on-line and cannot seem to find the part.  The dealer wants $55 for it.  A bit much, I think, for a piece of plastic.  Any idea where I can find the part for sale, or at least the part number?  Thanks much.

Posted by on

  • PennRower Nov 07, 2008

    Toyota Ed - Thanks.  Much appreciated.  Is there an official name for this piece of trim? - Mike

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 1,861 Answers

71812-AA010-B0 USA built ( 1st letter of serial # is a "4" )

71812-33050-B0 Japan built ( 1st letter of serial # is a "J" )

Posted on Nov 07, 2008

  • Toyota Ed Nov 07, 2008

    Thanks for the FixYa. Much appreciated.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can a manual seat replace the power seat - camry, 1999 front driver seat


Yes, if you purchase a manual set is will bolt in just the same so long as its the same model and year as they do change from year to year.

Jan 12, 2015 | 1999 Toyota Camry

2 Answers

Location of fuel filter


on the frame on the drivers side

Mar 03, 2014 | 2009 Honda Accord EX

1 Answer

Broken trim on driver seat 2010 navigator


I used zip ties to tighten it back down on my 2006 navigator. Sounds like same flaw in manufacturing covers many year models. The zip ties( large ones) helped for a long time but I'm still looking for better longer term fix myself.

Feb 27, 2012 | Lincoln Navigator Cars & Trucks

1 Answer

How do you install a driver seat plastic shield on a 2004 Ford Explorer? Its the piece of hard plastic between the door and the seat - part number 1L2Z-7862187-BAC


see if this helps
  1. Remove the rear trim screw.

snorkelbobby_44.gif
  1. Remove the lower trim screw.

snorkelbobby_45.gif
  1. Release the side trim front retaining clip.
  2. Pull the lumbar mechanism out slightly from the seat.
  3. Push down and pull out, releasing the side trim front retaining clip.
  4. CAUTION: Take care when removing the side trim cover. Excessive force will break the mounting tabs.

snorkelbobby_46.gif
Release the side trim from the mounting bracket.

snorkelbobby_47.gif
  1. Disconnect the seat control switch electrical connector.

Mar 25, 2011 | 1998 Ford Explorer

1 Answer

How to remove front dopr panel on 1995 Lincoln Town Car


Front Door Panel - Town Car - Removal
CAUTION: To avoid breakage of door pull cover(s), insert a screwdriver diagonally between pull strap and chrome bracket. Snap out both sides then remove.

Snap out two door pull strap retaining screw covers. Remove screws.

Remove two screws on front and rear side of front door trim panel.
The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.
Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.

NOTE: Do not use front door trim panel (23942) to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.

Remove window regulator control switch housing from back of front door trim panel . Lift up housing, remove retaining screws and disconnect all connectors.

Disconnect driver seat regulator control processor switch (driver door only) if equipped.
Twist out interior lamp wire assembly and remove the front door trim panel.
Installation

Ensure plastic watershield is secured to door panel.
Position front door trim panel to door. Connect interior lamp wiring.
Position the window regulator control switch housing and connect switch connectors. Install the retaining screws.
Connect driver seat regulator control processor (14C708) (driver door only) if equipped.
Align door lock side to its mating slide on the sheet metal (front doors only).
Snap in front door trim panel. Ensure all retainers fit properly.
Install two retaining screws on front and rear side of front door trim panel .
Install two retaining screws and pull strap covers.

Good luck Remember rated this).

May 31, 2010 | Lincoln Town Car Cars & Trucks

1 Answer

Wear is the batary on VW touareg 2 5 tdi


are you really ready for this..
if (typeof InitForm != "undefined") InitForm('lookup1','autodiv1','down');
Under the drivers seat. OK, let's add to this...

It's a tad more complicated. There are two plastic covers at the front of the seat on the floor. You need to lift both of them up. That exposes a fastener that will require a 10mm "triple square" male tool. This is similar to the familiar Torx (6 point star) fastener except it has 12 points instead of 6 points. This tool is available at many auto supply places, without it, you will NOT replace the battery. Remove both screws (they're TIGHT!!!), remove the plastic trim pieces from the rear of the seat slide assembly (carefully snap off) Tilt the seat back all the way forward, slide the seat forward almost all the way but leave space to miss the steering wheel. Now push back on the seat back and the entire seat will tilt to the rear exposing the battery box under the drivers seat. There are four clips that hold the cover on, unhook them, remove the torx screw holding the heater deflector to the battery box lid, remove the wire tie holding the wire to the top of the box and remove the box cover. Now you see the battery. Remove the gas vent plastic pipe from the front, remove the metal cover at the front left corner (10mm socket) it will not come out until you remove the (-) cable but don't just yet. remove the side clamp (10mm socket) and the battery is loose and free. It would be smart (but not required) to provide a 12 volt electrical source to the battery terminals as you replace the battery to help keep all of the radio GPS etc, settings. Remove the terminals, lift out the battery.

Sep 16, 2009 | Volkswagen Touareg Cars & Trucks

1 Answer

Need to find a way to take off the drivers side window motor


Motor
  1. Disconnect the negative battery cable.
  2. Remove the door trim panel and watershield.
  3. Detach the motor wires at the multiple connector.
  4. Remove the motor retaining screws using Torx® drive bit set D79P–2100–T or equivalent, and separate the motor from the bracket and cable drum housing.
  5. Remove the motor from inside the door.
To install:
  1. Position the motor and drive to the cable drum housing and motor mounting bracket. Install the 3 motor screws and tighten.
  2. Connect the power window motor wiring.
  3. Connect the negative battery cable.
  4. Check window operation.
  5. Install the watershield and door trim panel.

Door Panel
  1. Disconnect the negative battery cable.
  2. Snap out the two door pull strap retaining screw covers. Remove the screws.

CAUTION To avoid breakage of the door pull covers, insert a small screwdriver diagonally between the pull strap and chrome bracket. Snap out both sides then remove.


  1. Remove the two screws on the front and rear side of the front door trim panel.
  2. Using the trim pad removing tool, pry the trim panel retaining clips from the door inner panel.

NOTE Do not use the front door trim panel to remove the trim clips from the door inner panel. Replace any bent, damaged or missing push pins.


  1. Remove the window regulator switch housing from the back of the front door trim panel. Lift up the housing and disconnect all connectors from the switch housing.
  2. Disconnect the driver seat regulator control processor switch if equipped.
  3. Twist out the interior lamp wire assembly.
To install:
  1. Ensure that the plastic watershield is secured to the door .
  2. Position the front door trim panel to the door. Connect the interior lamp wiring.
  3. Align door lock side to its mating slide on the sheet metal.
  4. Snap in the front door trim panel. Ensure all retainers fit properly. Install the two retaining screws on the front and rear side of the front door trim panel.
  5. Connect the driver seat regulator control processor, if equipped.
  6. Position the window regulator control switch housing and connect the switch connectors. Install it to the front door trim panel by snapping it in, or by installing the screw at the rear.
  7. Install the two retaining screws and pull strap covers.
  8. Connect the negative battery cable.
053777a.gif

Aug 27, 2009 | 2000 Lincoln Town Car

1 Answer

Driver power seat


Yes, that piece is called the "recline cover". You will need the trim color code from the vehicle identification plate on the inside driver's door frame to match the trim plastic color. This is going to be a dealer part or perhaps an ebay part but make sure the trim color is a match.

Apr 30, 2009 | 2004 Honda Odyssey

2 Answers

Replace speakers on 95 camry


Remove the inner door handle. Remove the plugs that hide the door panel bolts, remove the bolts. If the panel has a light at the bottom edge, pull it out & disconnect it. Remove the 2 trim plugs from the latch side of the panel. Remove the 2 screws at the fron edge that are under plastic covers. Remove the window master switch and unplug it. Starting at the bottom, pull the panel off. The rear speakers may be a bit more difficult; if you can get to them from inside the trunk, good. If not, you have to pull out the rear seat, back and bottom. Remove the rear finishes from beside the seat. Remove the C pillar trims, and pull the rear shelf out in front of the back glass. Replace the speakers.

Sep 10, 2008 | 1994 Toyota Camry

Not finding what you are looking for?
2000 Toyota Camry Logo

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...