Question about 1995 Ford Explorer

1 Answer

Blower problem the blower switch on 2002 ford explorer dosent work on 1st 2end 3 rd speed on the forth i dose how can i know where to fine this problem thanks john

Posted by on

  • trevorw306 Nov 13, 2008

    Similar problem, although I have replaced the blower motor. It works on high most of the time and after being on for awhile it stops working and the blower motor sometimes is sluggish even on high. Any help would be great.



    Thanks



    Trevor

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 150 Answers

The blower motor resistor:

  • is located on the heater core and evaporator core housing near the blower motor.
  • has three resistor elements mounted on the resistor board to provide four blower motor speeds.
  • depending on the blower motor switch position, series resistance is added or bypassed in the blower motor circuit to decrease or increase blower motor speed.
  • has an overheating device (thermal limiter) that will open the resistor coil when the temperature reaches approximately 184°C (363°F) , interrupting the blower motor operation in all speeds except high.
  • is serviced as an assembly. The thermal limiter cannot be reset and is not serviceable.
REMOVAL
  1. Lower the glove compartment.
  2. Remove the screws and position aside the 4x4 control module.
  3. Remove the blower motor resistor.
4 Disconnect the electrical connector. 5 Remove the screws and the blower motor resistor. INSTALLATION
  1. To install, reverse the removal procedure.

Posted on Nov 07, 2008

  • Brian032472
    Brian032472 Nov 07, 2008

    If you have anymore questions on this I am happy to help. It's a very common complaint and a very easy diagnoses with that symtom.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 ford explorer sport trac blower motor and switch not getting any power, it was working fine a while ago and i had to start flipping the switch to head then off then back to head, what is wrong?


The selector switch on the dash controls the blower motor relay, then the fan switch controls the speed. The fan switch gets power from a 40amp fuse and the control panel gets power from two other fuses.
If you are working the control switch to get the fan to work, the control switch may be failing.

May 28, 2013 | 2003 Ford Explorer Sport Trac

1 Answer

Heater blower dont work from 1 to 3 speed


Most likely cause is the blower motor resistor block. 1,2and 3 go through the resistor forth speed is is full blast therefore bypasses the resistor being the only speed setting that works when the resistor has failed

Jun 13, 2012 | 2004 Ford F150

2 Answers

Focus 2002, A/C fan does not work on settings 1-3


common problem, replace the blower motor (fan) resistor, this is what controls the fan speed,its located on heaterbox next to blower motor.heres a picture of it,its on the rightside of dash toward the bottom. hope this helps.852ab4f.jpg

Feb 19, 2010 | 2000 Ford Focus

1 Answer

Shakes or Wobbles problem 2002 Ford Explorer V8 Two Wheel Drive Automatic 58000 miles When I am coasting starting about 30 mph or higher i have a lurching movement of back and forth. As soon as I step on...


Hi..my name is Keith..and i can think of 3 possible causes..the 1st one is a tire out of balance..sometime the wheel balancing weights come off...the 2nd one is that the belts in a tire is broken..and the 3rd one is..that you have a warped brake rotor..it shouldnt cost much to have a shop to look at it and fix it..i hope this has helped

Jun 27, 2009 | 2002 Ford Explorer

1 Answer

2003 Ford Explorer Fan Blower Motor


Jeff, If I understand you correctly you say your blower motor only works on high? check your blower motor resistor, located next to blower motor. The resistor makes the other speeds availiable, high bypasses the resistor, let me know if that fixes you up

May 27, 2009 | 2003 Ford Explorer

1 Answer

2006 Ford Explorer XLT the Blower Fan only works on 4 and 3 Sp


Look under the dash on passenger side and just to the left of the blower motor housing you will see the 4WD control module.Remove the 2 screws holding the module and let it hang down and your resistors are behind this.Remove the 2 screws holding the resistors and remove.
Now I am assuming you have manual climate control and not electonic.

Feb 25, 2009 | 2006 Ford Explorer

1 Answer

Car raidio


speakers: L/F - OG/LG [+] LB/WH [-]
L/R - GY/LB [+] TN/YE [-[
R/R- OR/RD[+] BN/PK [-]
R/F- WH/LG [+] DG/OR [-]
WH/YE HOT f2 20 amp fuse box
BK/PK HOT VPWR
RD/BK illumination
RD/LB Hot in start f2 5 amp fuse box
BK ground
BK/LB ground
BK/OG ground
as far as I know there isn't a "remote" wire unless you are dealing with steering wheel switches
Hope this helps!!

Feb 02, 2009 | 2002 Ford Explorer

1 Answer

1995 Ford Explorer heater/ac not working -


that cliking you hear is most likely the heater relay. but i don't think thats it, i would be checking to see if there is a resister, for the blower motor, it should be someware around the blower motor along with the relay in the same place. it will be on the heater box held in with a couple of screws, and a plug going to it with 4 or 5 wires.when they go bad, blower may only work on one or two speeds or not at all.

Jan 12, 2009 | 1994 Ford Explorer Limited

Not finding what you are looking for?
1995 Ford Explorer Logo

677 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...