Question about 2005 Sterling 827

1 Answer

1991 sterling 827

Looking for a brake master cylinder w/ abs

Posted by on

  • store2004 Nov 06, 2008

    Looking for a supplier for brake master cylinder for 1991 sterling 827 w abs

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 740 Answers

Same as the Brake master on 1991 Acura legend.

Posted on Jan 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1991 Mazda Navajo and put a new master cylinder on it and now I have brake pedal fade .


bleed the whole system back to front..still fade you are getting air somewhere... may have to bleed the master out of the car then put back

Dec 14, 2014 | 1991 Mazda Navajo

1 Answer

1991 Mazda B2200 Series Brake light and Anti-lock light on? Brake pedal pushed to the floor and truck won't stop. Is it the master cylinder and wheel bearing?


The master cylinder and the wheel bearings are completely un realated parts. The first thing to check is the brake fluid level. If it's full and you have zero braking and zero pedal then you may well have a dead m/c. If you find an empty reservior, fill it and then figure out where it went. A leak anywhere will have the same result, no fluid, no brakes. The ABS issue may or may not be related but you need to solve the no pedal problem first.

Nov 05, 2013 | 1991 Mazda B-Series

1 Answer

1991 Sterling 827 SL engine turns over, won't start, no spark. Any ideas?


Dear Sir:
1) You mus do ignition system to the specification manufacturer!
2) Recalibrate GAP Spark Plug for specification manufacturer.
3) See the diagrams attached, and proceed according with logic.
God bless you

5_25_2012_8_03_11_am.jpg5_25_2012_8_03_31_am.jpg5_25_2012_8_03_58_am.jpg5_25_2012_8_04_22_am.jpg5_25_2012_8_04_39_am.jpg

May 24, 2012 | 1989 Sterling 827

2 Answers

Abs is not working on my 1991 chevy s10 blazer


JUL 19, 1999 | Recall ID# 39106 Hide Details

Recall Reason SERVICE BRAKES, HYDRAULIC:ANTILOCK Recall Date JUL 19, 1999 Model Affected S10 Potential Units Affected 1125749
Recall SummaryVEHICLE DESCRIPTION: CERTAIN 4-WHEEL DRIVE PICKUP TRUCKS AND SPORT UTILITY VEHICLES EQUIPPED WITH ABS (ANTILOCK BRAKING SYSTEM) MANUFACTURED FROM SEPTEMBER 1989 THROUGH AUGUST 1996. UNDER CERTAIN DRIVING CONDITIONS THE SWITCH WHICH SIGNALS THE ABS SYSTEM WHETHER THE VEHICLE IS IN 2-WHEEL OR 4-WHEEL DRIVE CAN MALFUNCTION CAUSING INCREASED STOPPING DISTANCES DURING ABS STOPS WHILE IN THE TWO-WHEEL DRIVE MODE.

ConsequenceIF THIS OCCURRED AT A TIME WHEN MINIMUM STOPPING DISTANCE WAS REQUIRED, A VEHICLE CRASH COULD OCCUR WITHOUT PRIOR WARNING.

RemedyDEALERS WILL REPLACE OR REPAIR THE 4-WHEEL/2-WHEEL DRIVE SWITCH.

Jan 28, 2010 | 1991 Chevrolet S-10 Blazer

3 Answers

Location of brake light switch for 2007 sterling lt9500


should be on brake pedal next to the rod going to master cylinder

Jan 16, 2010 | 2007 Sterling 827

1 Answer

Rear brakes wont bleed. Sucks fluid in when brakes applied. Has ABS.


try this. open the two bleeder screw at the rear calipers. leave it open untill the fluid drips generously. close the bleeder. try the brakes. if it works bleed it the nornal way. note: make sure you dont run out of fluid in the master cylinder

Jun 02, 2009 | 1991 Lincoln Mark VII

1 Answer

Spongy brakes


Does sound like you need a new master cylinder. On a 2000 you wont need to back bleed. You will just need to follow the instruction and bleed the master and all four points. you will probably need to bleed the ABS block and proportioning valve but only if they have bleeders on them.

May 31, 2009 | 2000 Ford Explorer

2 Answers

Front brake drag


Does it have abs breaks? I have heard of problems with the older abs systems.

Apr 13, 2009 | 1991 GMC S-15 Jimmy

1 Answer

Brake fluid transfer from Master pump to ABS pump


hi from uk if you are saying that the brake master cylinder reservoir fluid is falling in level? and that there is signes that fluid is leaking from the ABS hydraulic master cylinder ie fluid is leaking from the arpeture where the electrics wiring loom enters then there is probably one of the piston/valve seals leaking within abs assy ? or is leak from somewhere else? not had this problem before with fluid passing from abs assy resulting in reservoir losing fluid in this way?

Nov 11, 2008 | 1991 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

168 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sterling Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Randy Ohler

Level 3 Expert

14585 Answers

ray gallant

Level 3 Expert

41071 Answers

Are you a Sterling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...