Question about 1993 Toyota Camry V6

1 Answer

Harmonic Balancer Need to change my harmonic balancer on my 93 camry. How do you do it?

Posted by on

  • cory4501 Nov 06, 2008

    Any idea

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 1,861 Answers

I have had the balancers come off just by unbolting it, and popping it off with a pry bar. Other times, I have used 2 pry bars, each behind the pulley, and popped it off. A few times, I have had to get out the puller. Just depends how long the balancer was on, and how rusty it is. But, they are not so tight that a puller will not do the job. Try the 2 pry bars, that usually works. Hope this helps, and thanks for choosing FixYa. The graciousness of a FixYa rating would be greatly appreciated. Thanks.

Posted on Nov 06, 2008

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 1993 Geo Prizm Lsi Harmonic Balancer

Yes a harmanic balancer from tha corolla is the same thing. I had to do the same thing with my 95 geo. It works out to be a lot cheaper buying for a toyota than a geo.

Posted on Mar 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Do you have to pull harmonic balancer off to replace crankshaft position sensor on a 93 suburban 5.7


Yes you do....its right behind the harmonic balancer, note...do not use a pry bar to remove the balancer......

Jun 12, 2014 | 1993 Chevrolet K1500

1 Answer

I have an 2006 dodge stratus.im changeing the front crank seal.do I have to pull the engine out to remove the harmonic balancer?


You should be able to get to the harmonic balancer while it's in the car. Remove right tire( use jack stands to hold the car up- not a jack). remove the inner splash guide and the balancer will be exposed. Using 3 jaw puller to remove harmonic balancer

Harmonic balancer removal DodgeForum com

May 31, 2014 | Cars & Trucks

1 Answer

Harmonic balancer remove replace


i dont think is your harmonic balancer that dont make any sound check all the pulleys cose to change the harmonic ba... you havto remove and change your crank pulley along with it

Jan 29, 2014 | Plymouth Cars & Trucks

2 Answers

Cant get my harmonic balancer off my 93 honda civic lx 1.5 liter


You need a harmonic balancer tool to remove this item. It is held on by a lock key. You can also very gently try and use a pry bar of some sort and slowly moving around in a circle pattern get it to come off.

Jun 13, 2011 | Honda Civic Cars & Trucks

1 Answer

I need the location of the harmonic balancer on my 2.2l Ecotec engine. Car is 2004 Chevrolet Cavalier LS.


CRANKSHAFT PULLEY IS THE HARMONIC BALANCER.YOU NEED THESE TOOLS TO REMOVE HARMONIC BALANCER, YOU NEED HARMONIC BALANCER REMOVER AND INSTALLER TOOL.YOU NEED A LARGE PIN SPANNER WRENCH TO HOLD HARMONIC BALANCER IN PLACE WHILE LOOSEN THE HARMONIC BALANCER BOLT.

May 21, 2011 | Chevrolet Cavalier Cars & Trucks

1 Answer

How do i remove harmonic balancer & replace


YOU NEED A HARMONIC BALANCER PULLER TOOL AND A 15M SIX POINT SOCKET TO REMOVE HARMONIC BALANCER BOLT.TURN OFF RADIO AND REMOVE THE DRIVE BELT AND REMOVE THE NEGATIVE BATTERY CABLE. REMOVE THE STARTER SO YOU CAN PUT A LARGE SCREW DRIVER OR LARGE PUNCH TO STICK IN ONE OF THE FLY WHEEL HOLES TO KEEP ENGINE FROM TURNING WHEN YOU LOOSEN THE HARMONIC BALANCE BOLT. ALSO SCREW DRIVER AND PUNCH CAN KEEP ENGINE FROM TURNING WHEN REMOVER THE HARMONIC BALANCER. YOU WILL NEED A HELPER TO HOLD PUNCH OR SCREW DRIVER WHILE YOU LOOSEN THE BOLT. YOU CAN GO TO SEARS OR ANY AUTO PARTS STORE AND BUY HARMONIC BALANCER PULLER.TORQUE HARMONIC BALANCER BOLT TO 76 FT LBS.

Apr 23, 2011 | 2003 Pontiac Montana

2 Answers

I changed the harmonic balancer and now it is terribly out of time. Didn't touch any timing belts, distributor or the like. Any advice?


There may be a magnet on the harmonic balancer for the crankshaft sensor,

The cam and crank sensor call for spark to the plugs..

Some cars you need a Harmonic Balancer Installer Adapter,
to make sure everything is lined up and gaped..

Check the crankshaft sensor for damage from inproper install, also check the wires going to sensor,, some times the harmonic balancer are such a Pain!! to come off the sensor or wires get damage in the battle.






Nov 30, 2009 | 1995 Geo Prizm

1 Answer

I need a how to to change harmonic balancer for 1995 nissan maxima. step by step


First remove right front tire and support vehicle with a jack stand. Remove splash guard lower portion near the harmonic balancer. Remove all drive belts. First remove the A/C alternator belt. Loosen the 14mm bolt at the front of the belt tenioner and then loosen the tensioner bolt (it is the one that stands out, you use a socket on it.). The power steering adjuster bolt with be gained from the bottom. It has a 12mm bolt head on it. You will break the jamb bolt loose first and then loosen the adjusting bolt. Pull down on the belt the help move it after you've loosened it some.Then remove harmonic balancer bolt (19mm).If the harmonic balancer will not slide off the crankshaft then use a two finger gear puller. Place the harmonic balancer bolt back in the crankshaft but do not tighten it. Leave it about a half inch from being all the way in. Next place the puller onto the harmonic balancer (one finger on each side securely press into the belt groove. The center puller bolt will rest against the harmonic balancer bolt head. Tighten the puller bolt and make sure the harmonice balancer bolt does not turn. The balancer should come off at this point.

Aug 26, 2009 | Nissan Maxima Cars & Trucks

1 Answer

1993 Geo Prizm Lsi Harmonic Balancer


Yes a harmanic balancer from tha corolla is the same thing. I had to do the same thing with my 95 geo. It works out to be a lot cheaper buying for a toyota than a geo.

Jan 11, 2009 | 1995 Geo Prizm

1 Answer

Harmonic balancer


I would recommend to go to auto zone and get a printed out diagram and also get the price of the harmonic balancer you will need a puller to get the old one off

Dec 30, 2008 | 1990 Ford F350

Not finding what you are looking for?
1993 Toyota Camry V6 Logo

Related Topics:

216 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74115 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22082 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7188 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...