Question about 2004 Mitsubishi Endeavor

Open Question

How do you remove the plenum on the 04 Endeavor?

Good morning. I would really appreciate your help. How do you remove the plenum on the 04 Endeavor to get to the rear spark plugs? I took off all the bolts that I could see and the wiring, but when I attempted to lift it, it wouldn't budge. Please help. Thanks. My email is streekone@sbcglobal.net.

Posted by on

6 Suggested Answers

  • 2 Answers

SOURCE: 2004 Mitsumishi Endeavor

The front three should be easy enough. They are right in front of the intake plenum. (big black plastic looking thing on top of the engine. The back three are underneath the intake plenum. It seems like a lot to tackle but it is really not that bad.
As always, if you are not sure you have the skills to attempt this go to a qualified mechanic. I did mine in an afternoon.

Posted on Jul 21, 2008

  • 323 Answers

SOURCE: Remove plenum on 1998 Interpid

Assuming it is a 2.7 litre, you can get to the rear bolt of the housing with a quarter drive 8 mm wobble socket. If you have to lift the plenum, there are bolts down the center that will need a 10 mm socket. The center cover (if it still has one) just lifts off.

Posted on Apr 20, 2009

SOURCE: Timing Belt for 2004 Mitsubishi Endeavor

Yes, I would replace it according to the owner's manual. Could be very expensive if it breaks.

Charlie

Posted on May 31, 2009

  • 523 Answers

SOURCE: I need to change my spark plugs on a 04'

If you'll need to remove the intake (or plenum) from the engine there are @ 8-10 No. 12 nuts and or bolts which hold this in place. There are also 1-2 bracket (check by the firewall) you'll need to unbolt too. Be certain to replace the gasket that is found between the plenum and the intake and do not over tighten these nut/bolts only 20ft pounds or so. If you do remove this you'll have to remove the air inlet, throttle cables and remove hoses from the throttle body, some of which carry coolant to properlly preheat the air before enteringthe engine. I have worked on several early 89-93 Monteros without having to remove this for plugs; perhaps different under the hood of the sport.
I hope this may have helped,
Tom

Posted on Oct 15, 2009

steve_e_uk
  • 1673 Answers

SOURCE: how do I remove the passenger side wiper arm

they are a bit hard to remove, best way to do it is, after you have removed the nuts, lift the arm straight up on its tention so its in the air, then get a cloth or rag, rap round the bottom under the arm, then tap the centre of the arm and pull at same time...NOTE!!! do not tap hard as you can ruin the thread for the nuts, so little taps should do it5...hope that helps

Posted on Feb 12, 2010

  • 44 Answers

SOURCE: how do I remove the passenger side wiper arm

they are on tapered shafts.if you put the nut back on,you can tap it with a hammer.i hope you the idea,cause if you try to hard it might cost more than having someone show you how.good luck.

Posted on Feb 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can I get a owners manual for a 1997 35ft holiday rambler endeavor m/h. would like both a manual for the chassis and M/H


Good morning James

If you go to the Holiday Rambler Manuals Page here:
Manuals they have four entries for the Endeavor, including Gas, Diesel, and LE. There is also contact info there for the company, so they can likely help you if the Manuals at that link don't cover you.

Good Luck!
D

Nov 30, 2015 | Cars & Trucks

1 Answer

Is there a way to reset keyless entry for 04 endeavor?


Search Results

    2004 Mitsubishi Endeavor Key Fob Remote Programming ...

    blog.keylessentryremotefob.com/.../04/2004-mitsubishi-endeavor-key-fo...
    Apr 25, 2013 - 2004 Mitsubishi Endeavor Key Fob Remote Programming Instructions ... you might have visit us at Keylessentryremotefob.com You can also ...

    Mitsubishi - Free Keyless Remote Fob Entry programming .

    How To Replace Mitsubishi Endeavor Key Fob Battery 2004 ...

    ? 2:04
    www.youtube.com/watch?v=yeQRdre7O0Q
    Oct 31, 2014 - Uploaded by Keyless Entry Remote Inc
    ... will show you How To Replace Mitsubishi Endeavor Key Fob Battery 2004 2005 To Order This Remote ...

Nov 01, 2015 | Cars & Trucks

1 Answer

Dropped nut in the engine compartment of 2004 endeavor, safe to drive


I would remove the intake plenum again and check with a flashight and a telescopic magnet in each of the intake runners. You should be able to see the valve stem down the intake runner. It may be necessary to remove the lower intake manifold to remove loose bolt.

Nov 26, 2012 | 2004 Mitsubishi Endeavor

1 Answer

Cabin Air Filter - 2004 Mitsubishi Endeavor (Where?)


IT IS IN BEHIND THE GLOVE COMPARTMENT YOU HAVE TO TAKE IT OUT BY UNSREWING AND START FROM YOUR RIGHT SIDE

May 31, 2009 | 2004 Mitsubishi Endeavor

1 Answer

Timing Belt for 2004 Mitsubishi Endeavor


Yes, I would replace it according to the owner's manual. Could be very expensive if it breaks.

Charlie

May 31, 2009 | 2004 Mitsubishi Endeavor

1 Answer

Tune up 2004 mitsubishi endeavor


you have to take the plenum off. the big plastic thing on top of the engine.

Dec 22, 2008 | 2005 Mitsubishi Endeavor

1 Answer

Rear valve cover removal for 94 camry se v6


The best way to remove the rear valve cover is to remove the intake plenum. There is really no other way to do it. It is not a hard job, removing the intake plenum, but, trying to tackle the rear cover without taking off the plenum is almost impossible. If he does remove the plenum, make sure he replaces the plenum gasket. Hope this helps.
Thanks for choosing FixYa.

Dec 12, 2008 | 1995 Toyota Camry

1 Answer

Jetta has no gas pedal pressure


If this car has a carb, the most common problem is the auto choke mechanism get siezed/ gummed up. Remove tha carb plenum in the morning before starting. Depress the accelerator pedal and check that the flap on top of the carb has closed.

Dec 12, 2008 | 1988 Volkswagen Jetta

1 Answer

04 endeavor


Dodgy fuses/ wiring

Jun 15, 2008 | 2004 Mitsubishi Endeavor

1 Answer

2004 Mitsumishi Endeavor


The front three should be easy enough. They are right in front of the intake plenum. (big black plastic looking thing on top of the engine. The back three are underneath the intake plenum. It seems like a lot to tackle but it is really not that bad.
As always, if you are not sure you have the skills to attempt this go to a qualified mechanic. I did mine in an afternoon.

Jun 07, 2008 | 2004 Mitsubishi Endeavor

Not finding what you are looking for?
2004 Mitsubishi Endeavor Logo

Related Topics:

223 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...