Question about 1994 Jeep Grand Cherokee

1 Answer

Replacing serpintine belt

Where's the adjustment to remove old belt?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 94 Answers

There will be a slack adjuster, a flat roller you loosen off it will most likely be spring loaded that will allow you to remove and install the belt.good luck

Posted on Nov 06, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Remove/replace serpentine belt


there is a belt tensioner that you need a long handled ratchet to adjust then simply take old belt off and put new one on of buy one here Search results for serpintine belt tool

Mar 12, 2015 | Cars & Trucks

1 Answer

How to tighten fan belt on 1999 fairmount ghia v8


The cars today do not have belt adjustments they have what is caller a idler pulls that keeps a serpintine belt "all in one belt" that snakes around all the pulleys,thus the serpintine..name..anyway if it is slipping most likely the belt needs replacing or the idler itself is bad..neither can be adjusted..the fix is replacement...your car should have a belt route under the hood showing where it goes and the idler is spring loaded and easy easy to take the pressure off to take the old belt off and replace it..not a big job for garages if you wish not to DIY .good lucK

Oct 01, 2014 | Cars & Trucks

1 Answer

How to replace serpintine belt on a 1988 chevy scottsdale pickup.


You need a wrench to make lever on the tensioner to remove the old belt, best if someone holds it while you remove the belt, make sure the belt label is on under the hood somewhere, or better yet, take a quick picture with your phone to make sure you put the new one back on the right way...
Hope this helps...


Aug 19, 2011 | Chevrolet C1500 Cars & Trucks

1 Answer

How to change serpintine belt 2002 3.5 aurora


Use a 3/8" breaker bar to move the belt tensioner. While holding pressure on the tensioner, remove the serpentine belt from any of the pulleys. Gently release pressure from the tensioner. Remove the old belt and replace with the new one. Reapply pressure to the tensioner and pop the belt over the last pulley.

Aug 27, 2010 | 2002 Oldsmobile Aurora

1 Answer

Alternator


First you need to remove the serpintine belt or alternator belt. If it is a serpintine locate the tension pully(the one that doesn't look like it does anything) place a wrench over the pully bolt and pull while removing the belt. Most generaly all alternators have two bolts holding them in. Remove both bolts. and remove alternator on some vehicles you need to remove the top engine mounts to remove the acctual alternator. make sure you if you do this you put a jack under the bngine block. NEVER ON THE OIL PAN. After that simply remove the old alternator and replace it with the new one reinstall the serpintine belt as instructed on either the underside of your hood or where the hood latch is.

Apr 10, 2010 | 1993 Toyota Corolla

1 Answer

Need to replace old serpintine belt how do I relieve the tension


On belt tensioner pulley fit a wrench on the bolt that holds pulley, turn clockwise to release tension, hold and remove belt.

Jan 04, 2010 | 2003 Oldsmobile Alero

1 Answer

How to fix the serpintin belt


Replace the belt, dont fix the old one. use a breaker bar to lift up on the belt tension pulley. while holding it up slide off the belt from one of the other pulleys. ***Slowly release the tensioner.*** then remove the belt. replace with a new belt (the same size as the old one) put it on all the pulleys except the last one. lift the tensioner up then slide the belt over the last pulley. recheck all pulleys to see if belt is on all pulleys correctly. then start engine.

Oct 03, 2009 | 1992 Honda Accord

1 Answer

Serpintine belt replacement


There is a pulley that appears to be not operating anything. This is an idler pulley, Attach a socket to the center of the pulley, when apply pressure it will turn releasing pressure on the belt, remove belt paying attention to the route. Replace belt as it came off. You will be fine.

Jul 05, 2009 | Saturn SC1 Cars & Trucks

1 Answer

Replace the serpentine belt


First note the route of the belt. make a drawing.
Adjustments are made by moving the power steering pump. far right of belt system.
loosen top fixed bolt above center of drive wheel on p/s pump.
loosen bolt below drive wheel on p/s pump.
Push p/s pump to the left to loosen belt.
Remove old belt .replace following route of your drawing.
move p/s pump to right .
top of belt should have 1/2 inch deflection.
tighten bolts
The end

If you dont have belt route mail me at
andymalt61@hotmail.com
for drawing

Good luck .Andy Bartolo

Mar 17, 2009 | 1998 Jeep Cherokee

1 Answer

How do you put on a serpintine belt


i believe that on that particular car you may need to remove the motor mount to be able to replace the belt

Aug 06, 2008 | 2000 Oldsmobile Intrigue

Not finding what you are looking for?
1994 Jeep Grand Cherokee Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...