Question about 2000 Ford Windstar

1 Answer

2000 ford windstar heater blowing cool air

The damper mixing door motor was replaced. The damper seems to be working ok.Heater only get warm. The engine temp. is normal and the heater input and output hoses are getting hot.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Hi, You may have an air lock in the system. Have you ever had the system flushed out? This might be the fix. Also the thermostat might need to be replaced. You didn't say if you hear the clicking noise. If you do hear the clicking noise when you adjust the tempture control then its back to the replacement of the blender motor box with broken gears.
Hope this helps Warren

Posted on Nov 17, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No heat. New thermastat, heater core flushed, good circulation. Has a rear heater.


Does blower motor work , air blowing out of ducts ?
Temperature blending is varied by the air temperature control door, which regulates the amount of air that flows through and/or around the heater core (18476) , where it is then mixed and distributed.
Movement of the control knob from COOL (Blue) to WARM (Red) causes a corresponding movement on the air temperature control door and determines the temperature that the system will maintain.
Temperature Control
The temperature control operates in the following manner:
  • Temperature control of the heater system is determined by the position of the temperature control knob (between COOL-BLUE and WARM-RED) of the heater control .
  • This control knob is connected to a potentiometer mounted in the heater control . This potentiometer is electrically connected to the electric blend door actuator that operates the A/C air temperature control door.

Feb 25, 2016 | 1996 Ford Windstar

1 Answer

Heater temp on high only bows luke warm air after driving. A/C works just fine.Plenty of cold air from it


heater blows cold air idle chrysler 300 Questions & Answers ...

www.fixya.com > Forum > Tags
Find solutions to your heater blows cold air idle chrysler 300 question. ... blow warmair for a few mins then back to luke warm. i replaced thermostat ... HEAT BLOWSCOLD AIR WHEN IDLING ONLY GETS HOT WHEN START DRIVING ... About 15 minutes after driving the diver side vents start blowing straight cold air but the ...

Heater only works when pressing the gas? - DoItYourself.com ...

www.doityourself.com/...repairs.../459521-heater-only-works-when-pres...
Nov 3, 2011 - When I press the gas, the air from the vents is nice and hot. .... So am Idriving a car with a ton of problems, or could the power steering ... Just anotherquestion, when warmed up does the engine temperature ... When the heater is on and I'm not pressing the gas pedal, luke warm air blows from the vents.

Heater blows cool air when stopped and warm air while ...

https://www.reddit.com/.../heater_blows_cool_air_when_stopped_...

RedditFeb 12, 2014 - Heater blows cool air when stopped and warm air while driving 2008 Kia Spectra (self. ... just fine but appears to blow cool air when I was stopped at a stoplight. ... My temp gauge would also be pegged high when at idle / low RPM. ...thermostat only blocks coolant going to the radiator, and the heater core, ...Missing: 300m ‎luke

Why is My Car AC Blowing Hot Air? - BlueDevil Products

gobdp.com/blog/car-ac-blowing-hot-air/

Jan 27, 2016 | 2000 Chrysler 300M

1 Answer

The A/C pump starts when i move heater controls to defrost or mix


Great question dustin but the A/C is suppose to come on in defrost or mix mode- this is floor & defrost. Does not seem to make sense does it. One of the things the a/c does is remove the moisture from the air. You need warm DRY air to remove the moisture from the windows. An automotive H.V.A.C. ( Heating,Ventilation,Air conditioning) first forces air thru the a/c evaporator core then thru the heater core and out the selected vent. If you only want a/c a blend door will by-pass the heater core which is controlled by a hot/cold knob or digital temp cotrol on the dash. Now back to the cold air problem- assuming the basics are all ok- Coolant is full, Engine gets up to proper operating temp-around 195 degrees- upper radiator should be hot. Both heater hoses should be hot. If thats all OK the blend door might not be working. It is controlled by an electric motor called a Blend Door Actuator which are prone to fail. I have replaced many on ford vehicles. Hope this helps

Nov 26, 2013 | 2006 Ford F-250 Super Duty

1 Answer

Heater not blowing warm air


the windstar has a problem with heater control doors

Nov 30, 2011 | 2000 Ford Windstar

1 Answer

2001 FORD EXPEDITION XLT 4.6L V8 BLOWING MILD WARM BUT NOT WARMING THOROUGHLY. HAVE FLUSHED COOLING SYSTEM THREE TIMES, AND CHANGED THERMOSTAT. HAVE ALSO REMOVED DASH AND REPLACED "BLEND DOOR" AND BLEND...


You hot air comes from the water circulated through the heater core. It is like a miniture radiator with water flowing thru it constantly. So by opening the "Blend Door" you are permitting so much of this hot air to pass thru.

Seems like for some reason your heater core is plugged up. Just like a radiator can be. So water may be passing through your heater core but not passing through fully. Your heater core gets hot from water passing throught it from the engine. Then your doors open up, in proportion to how much air is permitted to pass over the heater core.

Suggest to remove the heater core and replace it. Seems the blend doors are working properly but again, if you have a non working heater core then no air can pass over the "Hot Core" for you to recieve hot air.

If you are not mechanically inclined, then go to a local parts store and you can buy a car manual, such as Chilton's or Hane's Car manuals, for your year and make to show you how to replace it. Then you can also have it for any other problems that may arise.

Jan 24, 2010 | 2000 Ford Expedition

1 Answer

2000 ford windstar 3.8L Front heater has


what stopped? the air doesnt blow,if thats the case then replace the blowermotor resistor, its located on heater box on passengerside next to blower motor.hope this helps, let me know if this was the problem.

Dec 24, 2009 | 2000 Ford Windstar

1 Answer

Ford Windstar SE, 3.8L V6, 1999, front seat heat/defrost is cold


the blendor actuators strip out the gear inside the actuator cases on these all the time. replace the actuator.

Mar 10, 2009 | 1997 Ford Windstar

3 Answers

Heater


Likely it has more to do with the door that controlls the airflow. Which should be operated by vacum might check and make sure all thevacum lines are plugged in.

Does the gauge in the car show it warms up?

Feb 24, 2009 | 2001 Ford Windstar

2 Answers

Front heater does not work


i would suspect a temperature blend door motor has failed , it is common , go to an automotive repair shop and get a free estimate for repairs.

Dec 20, 2008 | 2001 Ford Windstar

Not finding what you are looking for?
2000 Ford Windstar Logo

253 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...